AT&T 230 Quark pdf 7/22/98 12:13 PM Page 1 TRIMLINE Memory Telephone 230 User’s Manual Part 2 © 1998 Philips Consumer Communications, L.P. All rights reserved. Printed in Mexico.
AT&T 230 Quark pdf 7/22/98 12:13 PM Page 2 PARTS CHECKLIST Remember to save your sales receipt in case you ever need warranty service, and make sure this telephone package includes the items shown below: TELEPHONE HANDSET Receiver Volume TELEPHONEBASE Switchhook Handset Tab Dial Ringer Program Mode Volume Button Switch 7-foot line cord Coiled handset cord 1
AT&T 230 Quark pdf 7/22/98 12:13 PM Page 3 TABLE/DESK INSTALLATION This telephone includes a 7-foot line cord with a modular plug on each end. Use this cord to connect the telephone to a modular jack. 1. Fill in directory card Remove the directory card and write in your own telephone number. Also write the telephone numbers (or names) that you want to store in each memory location. Reinstall the card and clear plastic cover. 2.
AT&T 230 Quark pdf 7/22/98 12:13 PM Page 4 WALL INSTALLATION 1. Fill in directory card Remove the directory card and write in your own telephone number. Also write the telephone numbers (or names) that you want to store in each memory location. 2. Reverse handset tab To install the telephone on a wall jack, you must reverse a small tab beneath the directory card. This tab holds the handset in place when you hang up. Remove the directory card and plastic cover.
AT&T 230 Quark pdf 7/22/98 12:13 PM Page 5 WALL INSTALLATION (continued) 4. Install telephone base on wall jack Hold the base up next to the wall jack, and plug in the line cord (Figure 3). Then push the base against the wall jack and down until it is held securely by the mounting studs. NOTE: If you cannot fit the base onto the wall jack, remove the four non-slip pads. Figure 3 5. Set DIAL Mode switch Refer to step 4 in Table/Desk Installation. 6.
AT&T 230 Quark pdf 7/22/98 12:13 PM Page 6 OPERATION Redial This telephone always stores in memory the last phone number dialed. The redial memory can accept numbers up to 24 digits long. The number will remain in memory until you change it by dialing another telephone number. To dial the same number again, lift the handset, and press . Erasing Redial For privacy, you can erase the redial memory. Lift the handset, then press and hang up. Mute Hold down to turn off the handset microphone.
AT&T 230 Quark pdf 7/22/98 12:13 PM Page 7 OPERATION (continued) Ringer Volume The Ringer Volume switch allows you to turn the telephone ringer OFF, or set it to ring at LO or HI volume. You can dial or answer calls normally when the ringer is off. Other telephones in your home will still ring; they are not affected by the switch. Receiver (Handset) Volume The Receiver Volume switch on the side of the handset can be adjusted for a comfortable listening level. The switch has three volume positions.
AT&T 230 Quark pdf 7/22/98 12:13 PM Page 8 MEMORY DIALING Memory Features Numbers will remain stored in memory unless you erase or change them by entering other numbers. Capacity: This telephone can store up to 12 different phone numbers, each up to 24 digits long. One-Touch Dialing: Three numbers can be stored in one-touch memory locations. You can dial these numbers by pressing one of the buttons marked with an emergency symbol.
AT&T 230 Quark pdf 7/22/98 12:13 PM Page 9 MEMORY DIALING (continued) Emergency Numbers: You may choose to store emergency numbers in the one-touch memory locations marked with fire, police and medical symbols. However, we recommend that you also write the telephone number on the directory card so that if the memory feature does not function, you can still manually dial an emergency number.
AT&T 230 Quark pdf 7/22/98 12:13 PM Page 10 MEMORY DIALING (continued) One-Touch Dialing To program numbers into memory 1. Press . 2. Enter telephone number. You will hear a click when each button is pressed. 3. Press the memory button , or , where the number is to be stored. 4. Hang up after the number is entered correctly. Repeat steps 1-4 to store another number. 1. Press . 2. Enter telephone number. 3. Press the one-touch memory button. To dial 1. Listen for dial tone. 2.
AT&T 230 Quark pdf 7/22/98 12:13 PM Page 11 MEMORY DIALING (continued) Speed Dialing To program numbers into memory 1. Press . 2. Enter telephone number. You will hear a click when each button is pressed. 3. Press . 4. Enter a digit (1-9) for the memory location where the number is to be stored. 5. Hang up after the number is entered correctly. Repeat steps 1-5 to store another number. 1. Press . 3. Press . 4. Press memory location (1-9). 2. Enter telephone number. To dial 1. Listen for dial tone.
AT&T 230 Quark pdf 7/22/98 12:13 PM Page 12 IN CASE OF DIFFICULTY If this telephone does not work properly, try the following suggestions before seeking repair assistance. No Dial Tone ☞ Make sure all plugs are connected properly. Inspect the line cord connections at the modular jack and at the telephone. Also inspect the coiled handset cord connections at both ends. ☞ Unplug the telephone and connect it to another modular jack.
