2 L1 ON L2 /OF F Two-Line Digital Answering System with Time/Day Stamp 1772 ME 2 W MO AY CL OC K DEL ETE VO LU ME RE PE Fold open this paper for information about this product's installation and operation. Please read Part 1 — Important Product Information, included in this package. AT STO P FO RW AR PLA Y MIC LIN E1 LIN E2 Part 2 © Copyright 1998 Philips Consumer Communications L.P. All rights reserved. Printed in Mexico.
I N S T A L L A T I O N Install the Batteries For One Two-Line Wall Jack For Two Single-L L1 OR L1/L2 jack TEL SET jack L TEL SET jack Power cord L1 OR L1/L2 jack Two-line wall jack Line 1 jac Two-line phone with single cord INSTALL THE BATTERIES Open the battery door on the bottom of the unit by pulling on the tabs. Insert the batteries as indicated, then close the door.
I N S T A L L A T I O N ine Wall Jacks For Two Single-Line Phones L1 OR L1/L2 jack L2 jack For Two-Line Phone with Two Cords L2 jack TEL SET jack Power cord Power cord L1 OR L1/L2 jack Line 2 jack Line 1 jack ck Line 2 jack with dual outlet adapter Power cord Two-line jack with single jack adapter and dual outlet adapter e with d Two-line phone with two cords Two single-line phones 3 Plug the cord from the L2 jack on the system into the dual outlet adapter.
IN CASE If this answering system does not work properly, try the following suggestions before seeking repair assistance. MESSAGE WINDOW IS BLANK Make sure the power transformer is securely plugged into an electrical outlet not controlled by a wall switch. Use only the power cord supplied with your system. If you need a replacement cord, call 1 800 722-9125. Press O to make sure the system is turned on.
ANSWERING SYSTEM OPERATION ANNOUNCEMENT OPTIONS SELECT ANNOUNCEMENTS MESSAGE ALERT The Answering System 1772 lets you record up to 4 different announcements — A, B, C, and AO. Each can be presented to callers on either Line 1 or Line 2. You can assign the same announcement to be presented on both lines, or you can choose different announcements for each line. Set the Line 1 ANNC SELECT switch to A, B, C, or AO to select the announcement callers to Line 1 will hear.
ANSWERING SYSTEM OPERATION FORWARD/SKIP MESSAGES PRIORITY CALLING To skip to the next message, press F. To skip part of a message (cue), hold down F for a few seconds, then release it to resume playing. (The system beeps while F is held down.) To stop playing messages, press S. The priority call tone is preset to 99. Callers to whom you have given the Priority Calling Code will be able to signal you that they are calling. Callers must use a touch tone phone.
ANSWERING SYSTEM OPERATION A w a y You can operate the answering system while away from home using the telephone keypad (touch tone phone only), or voiceactivated commands. CONNECT WITH THE ANSWERING SYSTEM 1 Dial your telephone number. 2 When the system answers, enter your Remote Access Code during or after the announcement. The system announces the number of messages received, and beeps twice, indicating it is ready to receive commands.
ANSWERING SYSTEM OPERATION A w a y MEMORY FULL/NO ANNOUNCEMENT If the system answers after 10 rings, and presents 2 beeps but no announcement, the system might be off for one or both lines, memory might be full, or the system is set to AO and your announcement was lost. To reset the system to answer and record 1 Enter your Remote Access Code after the 2 beeps. 2 Listen to any recorded messages, and delete some or all of them. 3 Press 1 4 1 to review the Line 1 announcement.
2 ANSWERING SYSTEM 1772 1 Dial telephone number and wait for system to answer. 2 Enter Remote Access Code. 3 Listen for messages — OR — Enter touch tone command. 4 Hang up to save messages. Your Remote Access Code _______ © 1998 Philips Consumer Communications L.P. All rights reserved. Printed in Mexico. Issue 1AT&T 848229274 2 ANSWERING SYSTEM 1772 1 Dial telephone number and wait for system to answer. 2 Enter Remote Access Code. 3 Listen for messages — OR — Enter touch tone command.
OPTION PRESS Play messages 7, 17, or 27 Play only new messages 6, 16, or 26 Repeat message 2 Skip message 5 Delete selected message 3 Delete all messages 03, 13, or 23 Record announcement 14* or 24* Record memo 1* or 2* End a recording # Turn system on 00, 10, 20 Turn system off 88, 188 or 288 OPTION PRESS Play messages 7, 17, or 27 Play only new messages 6, 16, or 26 Repeat message 2 Skip message 5 Delete selected message 3 Delete all messages 03, 13, or 23 Record announcement 14* or 24* Record memo 1
