Introduction 第 49 頁，共 224 頁 The [Dial-up Connection] window will appear. 2. Confirm that "Direct connection" has been selected under [Connection Destination], and then click on the [Connect] button A connection will be initiated. Note { { { This is an example of what happens when you use "Direct connection" as a connection name under "Connect to access point." If a name different from the connection name is used, that name will appear under [Connection Destination].
Introduction 第 50 頁，共 224 頁 3 Enter the IP address and port number of the proxy server under [Proxy Server], and then click on the [OK] button 3. End the connection Right-click either on the connection icon under the [Bluetooth Settings] window or on the icon in the task tray, and then click on [Disconnect]. Click on the "Yes" button in the disconnection confirmation dialog box that appears. file://C:\Documents and Settings\anitachou\Local Settings\Temp\~hh114B.
Introduction 第 51 頁，共 224 頁 Connecting to a LAN using an access point (PAN) [PAN] This section describes how to connect to a network (for example, a company LAN or a personal home network) using a PAN profile-compatible access point. Please refer to "Using an access point (LAP) to connect to a LAN" if you are using a LAP profilecompatible access point.
Introduction 第 52 頁，共 224 頁 Note { Alternatively, click [Start]→[All Programs]→[Bluetooth]→[Bluetooth Settings], and then click on [New Connection] from the active [Bluetooth Settings] window. The [Add New Connection Wizard (Welcome to the Add New Connection Wizard)] window will appear. 3. Confirm that [Express Mode] has been selected, and then click on the [Next] button The [Add New Connection Wizard (Searching for Bluetooth devices)] window will appear.
Introduction 第 53 頁，共 224 頁 [Next] button The [Add New Connection Wizard (Searching for Services)] window will appear. You will be asked for the Bluetooth passkey in the window that appears. 5. Enter the passkey under [Bluetooth Passkey (PIN code)], and then click on the [OK] button file://C:\Documents and Settings\anitachou\Local Settings\Temp\~hh114B.
Introduction 第 54 頁，共 224 頁 Service detection and COM port creation will be performed automatically. The [Add New Connection Wizard (Connection Name Settings)] window will appear. 6. Enter the type and name of the icon displayed after registration, and then click on the [Next] button Please click on the [Next] button if you are satisfied with the settings. The [Add New Connection Wizard (Completing the Add New Connection Wizard)] window will appear. 7.
Introduction 第 55 頁，共 224 頁 Procedure 1. Right-click on the connection icon in the [Bluetooth Settings] window, and then click on [Connect] You will be asked for the Bluetooth passkey in the window that appears. 2. Enter the passkey under [Bluetooth Passkey (PIN code)], and then click on the [OK] button A connection will be initiated. Once you have connected to the network, Internet Explorer will start automatically, and you will be able to exchange data with other computers on the network.
Introduction 第 56 頁，共 224 頁 3 Enter the IP address and port number of the proxy server under [Proxy Server], and then click on the [OK] button 3. End the connection Right-click either on the connection icon under the [Bluetooth Settings] window or on the icon in the task tray, and then click on [Disconnect]. Click on the "Yes" button in the disconnection confirmation dialog box that appears. file://C:\Documents and Settings\anitachou\Local Settings\Temp\~hh114B.
Introduction 第 57 頁，共 224 頁 Building a personal area network [PAN] You can use the PAN profile to build a network of Bluetooth -enabled devices. →Operating as a server →Operating as a client A personal area network comprises a client -server architecture. The device to which other devices connect is called the "server", and a device that connects to the server is called a "client." The client-server relationship is not necessarily a fixed one.
Introduction 第 58 頁，共 224 頁 g , g g In addition, you will be able to configure folder and file sharing, which will allow data to be browsed by other servers or clients on the network. Important z Please refer to Windows Help for further information on TCP/IP, DHCP and configurations for sharing. Operating as a server The following icon will appear in the tasktray when the PAN server function has been activated.
Introduction 第 59 頁，共 224 頁 [ ] The PAN server will be activated, and an icon will accordingly appear in the tasktray. Other devices that use the PAN profile will now be able to connect over the network. Important z When using the device as the server, make sure that all user accounts have a password set for the security reasons. By clicking on the icon, the [Bluetooth PAN Server] window will appear. In the graphic below, one client has established a connection.
Introduction 第 60 頁，共 224 頁 { Alternatively, click on [Start] →[All Programs]→[Bluetooth]→[Bluetooth Settings], and then on [New Connection] from the [Bluetooth Settings] window. 2. Confirm that [Express Mode] has been selected, and then click on the [Next] button 3. Click on the [Next] button in the advisory dialog box The [Add New Connection Wizard (Searching for Bluetooth devices)] window will appear.
Introduction 第 61 頁，共 224 頁 The [Add New Connection Wizard (Searching for Services)] window will appear. The [Add New Connection Wizard (Confirm Connection Name)] window will appear. 5. Click on the [Next] button file://C:\Documents and Settings\anitachou\Local Settings\Temp\~hh114B.
Introduction 第 62 頁，共 224 頁 The registered icon will appear in the [Bluetooth Settings] window. ■Connecting to a server Procedure 1. Right-click on the icon in the [Bluetooth Settings] window, and then click on [Connect] Once you have connected, the icon will change to indicate that the device is connected. ■Ending a connection to a server Procedure 1. Right-click on the icon in the [Bluetooth Settings] window, and then click on [Disconnect] file://C:\Documents and Settings\anitachou\Local Settings\
Introduction 第 63 頁，共 224 頁 A message confirming whether you wish to disconnect will appear. Click on the [Yes] button. Once you have disconnected, the icon will change to indicate that the device is not connected. Using a modem station for fax transmissions [FAX] This section describes how to send a fax using a Bluetooth wireless modem station. →Setting up the modem station →Installing a modem →Setting fax information →Sending a fax file://C:\Documents and Settings\anitachou\Local Settings\Temp\~hh
Introduction 第 64 頁，共 224 頁 g →Receiving a fax Important z z z z Please refer to the modem station instruction manual for information on how to connect the station to a telephone line. Please ensure that any drivers used to connect the PC to the modem have been installed. A Bluetooth passkey (PIN code) is required for you to connect to the modem station. Please make a note of your Bluetooth passkey before you start the set -up process.
Introduction 第 65 頁，共 224 頁 The [Add New Connection Wizard (Searching for Bluetooth devices)] window will appear. Once the program has finished searching for the devices, the [Add New Connection Wizard (Select Device)] window will appear. 4. Select the device name of the wireless modem station from [Device List], and then click on the [Next] button file://C:\Documents and Settings\anitachou\Local Settings\Temp\~hh114B.
Introduction 第 66 頁，共 224 頁 The [Add New Connection Wizard (Searching for Services)] window will appear. 5. If you are connecting to the wireless modem station for the first time, enter the passkey for the device from the [Bluetooth Passkey (PIN Code)] window, and then click on the [OK] button Once the program has finished searching for the services, the [Add New Connection Wizard (Select Service)] window will appear. 6.
Introduction 第 67 頁，共 224 頁 The [Add New Connection Wizard (Connecting to Remote Device)] screen will appear. The COM port and modem registration process will then be automatically performed. Once the COM port and modem (standard 33600 bps type) registration is complete, the [Add New Connection Wizard (Setting Connection Name)] screen will appear. 7. Configure the type and name of the icon to appear after registration, and click on the [Next] button.
Introduction 第 68 頁，共 224 頁 8. Click on the [Finish] button The settings will be registered, and the icon will appear on the [Bluetooth Settings] screen. Setting FAX information Configure send/receive settings and register fax information. Procedure 1. Select [Start]→[Control Panel], and then double -click on the [Printers and Other Hardware] icon Note { If the control panel is displayed in "Classic view", and you use Windows 2000, please start from Step (2). 2.
Introduction 第 69 頁，共 224 頁 created in the [Printers and Faxes] screen. 4. Click on "Send a fax" under "Printer Tasks" on the left side of the window If you have not yet configured a fax device, the [Fax Configuration Wizard] window will appear. In the window you can enter settings pertaining to the sender (yourself).
Introduction 第 70 頁，共 224 頁 Note { The sender information that you configure here will be automatically appended as header information when you send a fax. The [Fax Configuration Wizard (Select Device for Sending or Receiving Faxes)] window will appear. 6.
Introduction 第 71 頁，共 224 頁 The [Fax Configuration Wizard (Completing the Fax Configuration Wizard)] window will appear. 8. Click on the [Finish] button The fax information will be have been registered, and the [Fax Console] window will appear. This will complete the fax set -up process. Related topics: " Sending a fax" and "Receiving a fax " Sending a fax This section describes how to send a fax from the Fax Console. Important file://C:\Documents and Settings\anitachou\Local Settings\Temp\~hh114B.
Introduction 第 72 頁，共 224 頁 Important z The Fax service must be enabled for sending in order for you to send a fax. Please refer to " Using a wireless modem station " under "Troubleshooting" for how to change the send and receive settings once the service has been configured. Procedure 1. Double-click on the [Fax] icon in the Control Panel The [Fax Console] window will appear. 2.
Introduction 第 73 頁，共 224 頁 The [Send Fax Wizard (Recipient Information)] window will appear. 4. Enter the name and fax number of the destination party, and then click on the [Next] button The [Send Fax Wizard (Preparing the Cover Page)] window will appear. 5. Specify the cover page template, subject line, and note (body text), and then click on the [Next] button The [Send Fax Wizard (Schedule)] window will appear. 6.
Introduction 第 74 頁，共 224 頁 The [Send Fax Wizard (Completing the Send Fax Wizard)] window will appear. 7. Confirm the destination information and transmission details, and then click on the [Finish] button The software will automatically dial the number and send the fax. Once the fax has been sent, Fax Monitor will revert to standby mode. file://C:\Documents and Settings\anitachou\Local Settings\Temp\~hh114B.
Introduction 第 75 頁，共 224 頁 , y Related topic: " Receiving a fax" Receiving a fax This section describes what to do when a fax arrives after you have established a connection to a modem station. Important z z The Fax service must be enabled for receiving in order for you to receive a fax. Please refer to " Using a wireless modem station " under "Troubleshooting" for information on how to change the send and receive settings once the fax service has been configured.
Introduction 第 76 頁，共 224 頁 Click on the message with your mouse to receive the fax. 2. Double-click on the [Fax] icon in the Control Panel The [Fax Console] window will appear. 3. In the [Fax Console] window, double -click on the fax that has arrived An image of the received fax will be displayed. Related topic: " Sending a fax" file://C:\Documents and Settings\anitachou\Local Settings\Temp\~hh114B.
Introduction 第 77 頁，共 224 頁 Using a mobile telephone for fax transmissions [FAX] This section describes how to send a fax using a mobile telephone as a modem. →Setting up the mobile telephone →Installing a modem →Setting fax information →Sending a fax →Receiving a fax Important z z z Please ensure that any drivers used to connect the PC to the mobile telephone have been installed. A Bluetooth passkey (PIN code) is required for you to connect to the mobile telephone.
Introduction 第 78 頁，共 224 頁 Note { Alternatively, click [Start] →[All Programs]→[Bluetooth]→[Bluetooth Settings], and then click on [New Connection] from the active [Bluetooth Settings] window. The [Add New Connection Wizard (Welcome to the Add New Connection Wizard)] window will appear. 3. Select [Custom Mode], and then click on the [Next] button The [Add New Connection Wizard (Searching for Bluetooth devices)] window will appear. file://C:\Documents and Settings\anitachou\Local Settings\Temp\~hh114B
Introduction 第 79 頁，共 224 頁 Once the program has finished searching for the devices, the [Add New Connection Wizard (Select Device)] window will appear. 4. Select the device name of the mobile telephone from [Device List], and then click on the [Next] button The [Add New Connection Wizard (Searching for Services)] window will appear. 5.
Introduction 第 80 頁，共 224 頁 Once the program has finished searching for the services, the [Add New Connection Wizard (Select Service)] window will appear. 6. Select "Fax" under [Select Service], and then click on the [Next] button The [Add New Connection Wizard (Connecting to Remote Device)] screen will appear. The COM port and modem registration process will then be automatically performed. file://C:\Documents and Settings\anitachou\Local Settings\Temp\~hh114B.
Introduction 第 81 頁，共 224 頁 Once the COM port and modem (standard 33600 bps type) registration is complete, the [Add New Connection Wizard (Setting Connection Name)] screen will appear. 7. Configure the type and name of the icon to appear after registration, and click on the [Next] button. Please click only on the [Next] button once you are satisfied with the configuration. The [Add New Connection Wizard (Completing the Add New Connection Wizard)] screen will appear. 8.
Introduction 第 82 頁，共 224 頁 3. Click on "Set up faxing" in the [Printers and Faxes] window A window showing installed programs will appear, and a Fax icon will have been created in the [Printers and Faxes] screen. 4. Click on "Send a fax" under "Printer Tasks" on the left side of the window file://C:\Documents and Settings\anitachou\Local Settings\Temp\~hh114B.
Introduction 第 83 頁，共 224 頁 If you have not yet configured a fax device, the [Fax Configuration Wizard] window will appear. In the window you can enter settings pertaining to the sender (yourself). Note { If the fax configuration information has already been registered, the [Send Fax Wizard] window, which can be viewed under " Sending a fax" below, will appear instead of the [Fax Configuration Wizard] window. 5.
Introduction 第 84 頁，共 224 頁 Note { If [Enable Receive] is selected, the device will be on standby for receiving faxes even if it is not sending or receiving anything, and therefore will be in continuous connection to the wireless modem （when COM Auto Connect is on). Please decide whether to select this option based on to the desired objective and/or frequency of transmission. The [Fax Configuration Wizard (Transmitting Subscriber Identification (TSID))] window will appear. 7.
Introduction 第 85 頁，共 224 頁 The fax information will be have been registered, and the [Fax Console] window will appear. This will complete the fax set -up process. Related topics: " Sending a fax" and "Receiving a fax " Sending a fax This section describes how to send a fax from the Fax Console. Important z The Fax service must be enabled for sending in order for you to send a fax.
Introduction 第 86 頁，共 224 頁 2. In the [Fax Console] window, click [File] →[Send fax] The [Send Fax Wizard (Starting the Send Fax Wizard)] window will appear. 3. Click on the [Next] button The [Send Fax Wizard (Recipient Information)] window will appear. 4. Enter the name and fax number of the destination party, and then click on the [Next] button file://C:\Documents and Settings\anitachou\Local Settings\Temp\~hh114B.
Introduction 第 87 頁，共 224 頁 The [Send Fax Wizard (Preparing the Cover Page)] window will appear. 5. Specify the cover page template, subject line, and note (body text), and then click on the [Next] button The [Send Fax Wizard (Schedule)] window will appear. 6. If you wish to send the fax immediately, select "Now", and then click on the [Next] button The [Send Fax Wizard (Completing the Send Fax Wizard)] window will appear. 7.
Introduction 第 88 頁，共 224 頁 The software will automatically dial the number and send the fax. Once the fax has been sent, Fax Monitor will revert to standby mode. Related topic: " Receiving a fax " Receiving a fax This section describes what to do when a fax arrives after you have established a connection to a modem station. file://C:\Documents and Settings\anitachou\Local Settings\Temp\~hh114B.
Introduction 第 89 頁，共 224 頁 Important z z The Fax service must be enabled for receiving in order for you to receive a fax. Please refer to " Using a mobile telephone " under "Troubleshooting" for information on how to change the send and receive settings once the fax service has been configured. Please ensure you have connected to a modem station before you receive a fax (the device will be connected to the modem if "Enable Receive" has been selected or COM Auto Connect has been activated).
Introduction 第 90 頁，共 224 頁 An image of the received fax will be displayed. Related topic: " Sending a fax" Printing This section describes how to use a Bluetooth -compatible printer for printing. Types of printer functions When printing using Bluetooth, the methods for configuring and using the printer will vary with the corresponding profile.
Introduction 第 91 頁，共 224 頁 or other device" Note z z (*1) The majority of Bluetooth -compatible printers support HCRP. If you have selected Express Mode, HCRP will be chosen as the default profile. If the printer does not support HCRP, then SPP will be the next choice. (*2) The printing of business cards using OPP complies exclusively with the business card (vCARD) standard. Printing documents and images [HCRP] [SPP] This section describes how to print using a Bluetooth -compatible printer.
Introduction 第 92 頁，共 224 頁 Note { Alternatively, click [Start] →[All Programs]→[Bluetooth]→[Bluetooth Settings], and then click on [New Connection] from the active [Bluetooth Settings] window. The [Add New Connection Wizard (Welcome to the Add New Connection Wizard)] window will appear. 3. Confirm that [Express Mode] has been selected, and then click on the [Next] button The [Add New Connection Wizard (Searching for Bluetooth devices)] window will appear. file://C:\Documents and Settings\anitachou\Lo
Introduction 第 93 頁，共 224 頁 Once the program has finished searching for the devices, the [Add New Connection Wizard (Device Selection)] window will appear. 4. Select the device name of the printer from [Device List], and then click on the [Next] button The [Add New Connection Wizard (Searching for Services)] window will appear. 5. If you are connecting to the printer for the first time, enter the passkey for the device from the [Bluetooth Passkey (PIN Code)] window, and then click on the [OK] button.
Introduction 第 94 頁，共 224 頁 Once the services have been detected successfully, connection to the device and creation of the HCRP port will be performed automatically. If you have not yet installed a printer, a message prompting you to install a printer will appear. 6. Click on the [OK] button The [Add Printer Wizard (Starting the Add Printer Wizard)] window will appear. 7. Click on the [Next] button The [Add Printer Wizard (Local Printer or Network Printer)] window will appear. 8.
Introduction 第 95 頁，共 224 頁 The [Add Printer Wizard (Select Printer Port)] window will appear. 9. Select the desired port, and then click on the [Next] button The [Add Printer Wizard (Install Printer Software)] window will appear. 10. Select the [Manufacturer] and [Printer] as pertains to the printer to be installed, or click on the [Use Device] button, and then click on the [Next] button file://C:\Documents and Settings\anitachou\Local Settings\Temp\~hh114B.
Introduction 第 96 頁，共 224 頁 Please install the printer according to the instructions in the windows that follow. Once installation is complete, a message of confirmation will appear in the [Add New Connection Wizard (Printer Settings)] window. 11. Click on [Next] The [Add New Connection Wizard (Connection Name Settings)] window will appear. 12.
