Feint 3 Application Interface Pin Pin Name I/O Reset Value Pin Description Level 61 ATLANTIC Oo PD Unable ANT CTR, default low 18v 63 ATLANTIC oO PD Unable ANT CTR, default low 18v 65 ATLANTIC Oo PD Unable ANT CTR, default low 1.8V 3.8 Configuration Interface The FM101 module provides 4 configuration pins, they are output pins, used to read the level of H/L for the host system, so the host system can know the module type insert in the M.2 slot.
Feint 4 Radio Frequency 4 Radio Frequency 4.1 RF Interface 4.1.1 RF Interface Functionality The FM101 module supports two RF connectors used for external antenna connection. As the Figure 16 shows, “M" is for Main antenna, which is used to receive and transmit RF signal; “D/G" is for Diversity antenna, which is used to receive the diversity RF signal and GNUS signal. Figure 16. RF connectors 4.1.
Feint 4 Radio Frequency 4.1.3 RF Connector Dimensions FM101 module uses standard M.2 RF connectors. The RF connector part number is 818004607 manufactured by ECT cooperation, and the size is 2x2x0.6mm. The connector dimension is shown as following picture: 6.6 Immunity Figure 18. 0.81mm coaxial antenna dimensions Copyright © Flamenco Wireless Inc.
FiO 4 Radio Frequency J Site ABMS REEF TALE S. Figure 19. Schematic diagram of 0.81mm coaxial antenna connected to the RF connector 4.1.4 RF Connector Assembly Mate RF connector parallel refer Figure 20, do not slant mate with strong force. Copper sarcoma nine Wong connector mating Wot parallel= Le Figure 20. Mate RF connector To avoid damage in RF connector mating, it is recommended using pulling JIG as Figure 21, and the pulling JIG must be lifted up vertically to PCB surface (see Figure 22 and 23).
Feint 4 Radio Frequency Figure 21. Pulling JIG 4 LL Pui pulling Hd . { PUB Figure 23. Pulling direction 4.2 Operating Band The operating bands of FM101 module are shown in the following table: Operating Band Description Mode Tx (MHz) Rx (MHz) Band 1 2100MHz LTE FDD/WCDMA 1920-1980 2110-2170 Copyright © Flamenco Wireless Inc.
Einteilen 4 Radio Frequenz Operation Band Desorption Mode Tx (MHz) Rx (MHz) Band 2 1900MHz LTE FDD/WCDMA 1850-1910 1930-1990 Band 3 1800MHz LTE FDD 1710-1785 1805-1880 Band 4 1700MHz LTE FDD/WCDMA 1710-1755 2110-2155 Band 5 850MHz LTE FDD/WCDMA 824-849 869-894 Band 6 850MHz LTE FDD/WCDMA 830-840 875-885 Band 7 2600Mhz LTE FDD 2500-2570 2620-2690 Band 8 900MHz LTE FDD/WCDMA 880-915 925-960 Band 12 700MHz LTE FDD 699-716 729-746 Band 13 700MHz LTE FDD 777-787 746-756 Band 14 700MHz LTE FDD 788-798 758-768 Ban
Feint 4 Radio Frequency Operating Band Description Mode Tx (MHz) Rx (MHz) Band 39 1900MHZ LTE TDD 1880-1920 Band 40 2300MHz LTE TDD 2300-2400 Band 41 2500MHZ LTE TDD 2496-2690 Band 42 3500MHZ LTE TDD 3400-3600 Band 43 3700MHZ LTE TDD 3600-3800 Band 48 3600MHZ LTE TDD 3550-3700 GPS ONASSIS 1602.5625+4 BDS Galileo 4.3 Transmitting Power The transmitting power for each band of FM101 module is shown in the following table: Mode Band 3GPP Requirement Tx Power Note (dBm) (dBm) Band 1 23.541 Band 2 23.
FiO 4 Radio Frequency 3GPP Requirement Tx Power Mode Band dBm) (dBm) Note Band 39 23+2.7 231 MHz Bandwidth, 1 RB Band 40 23+2.7 23+1 MHz Bandwidth, 1 RB Band 41 2612.7 26+1 MHz Bandwidth, 1 RB (HUE) Band 41 (Non-HUE 2312.7 2341 MHz Bandwidth, 1 RB mode) Band 42 23+1 MHz Bandwidth, 1 RB Band 43 2321 MHz Bandwidth, 1 RB Band 48 211 MHz Bandwidth, 1 RB Module default max capability support HUE. The real working mode is decided support HUE, the module can work in HUE.
Feint 4 Radio Frequency 3GPP Requirement Rx Sensitivity Mode Band Note (dBm) Typicality) Band -106.7 TBD BER < 0.1% Band 5 -104.7 TBD BER < 0.1% Band 6 -106.7 TBD BER < 0.1% Band 8 -103.7 TBD BER < 0.1% Band 19 -106.7 TBD BER < 0.1% TBD MHz Band 1 -96.3 Bandwidth TBD MHz Band 2 -94.3 Bandwidth TBD MHz Band 3 -93.3 Bandwidth TBD MHz Band 4 -96.3 Bandwidth TBD MHz FILTERED pangs -943 Bandwidth TBD MHz Band 7 -94.
Feint 4 Radio Frequency 3GPP Requirement Rx Sensitivity Mode Band Note (dBm) Typicality) MHz Band 38 -96.3 TBD Bandwidth TBD MHz Bandanna -96.3 Bandwidth TBD MHz Band 40 -96.3 Bandwidth TBD MHz MALTED Bandanna -943 Bandwidth TBD MHz Band 42 -95 Bandwidth TBD MHz Band 43 95 Bandwidth MHz Band 48 -95 -102 Bandwidth The above values are measured in dual antennas condition (Main+ Diversity). For a single main antenna (without Diversity), the sensitivity will drop about DBMS for each band of LTE. 4.
FiO 4 Radio Frequency Test Result Description Positioning system Condition Typical Fixing TBD GPS Tracking TBD Sleep TBD Current Fixing TBD GPS+ BDRM GLOSSINESS Tracking TBD Galileo Sleep TBD Cold start TBD GPS Warm start TBD Hot Start i: TIFF Cold start TBD GPS+ BDRM GLOSSINESS Warm start TBD Galileo Hot Start TBD Tracking TBD GPS Acquisition TBD Sensitivity GPS+ BDRM GLOSSINESS Tracking TBD Galileo Acquisition TBD e& GNUS current is tested with RF disabled at 25°C temperature. 4.
FiO 4 Radio Frequency FM101 Module Main Antenna Requirement Frequency range Bandwidth (MADMAN) Bandwidth (LTE) The most proper antenna to adapt the frequencies should be used.
FiO 4 Radio Frequency FM101 Module Main Antenna Requirement Bandwidth (GNUS) Impedance Input power Recommended standing wave ratio (SWR) LTE band 26 (850): 80 MHz LTE band 28 (700): 100 MHz LTE band 29 (700): 12 MHz LTE band 30 (2300): 55 MHz LTE band 66 (1700): 490MHz LTE band 71 (680): MHz LTE band 38 (2600): 50 MHz LTE Band 39 (1900): 40 MHz LTE band 40 (2300): 100 MHz LTE band 41 (2500): 194 MHz LTE band 42 (3500): 200 MHz LTE band 43 LTE band 48 GPS: 2 MHz ONASSIS: 8 MHz BDS: 4 MHz Galileo: 2 MHz 50Q >
Feint 4 Radio Frequency cause FCC EIRE or carrier TRP certification fail. Copyright © Flamenco Wireless Inc.
FiO 5 ESD Characteristics 5 ESD Characteristics The module is generally not protected against Electrostatic Discharge (ESTES. ESD handling precautions that apply to ESD sensitive components should be strictly followed. Proper ESD handling procedures must be applied throughout the processing, handling, assembly and operation of any application with module. The ESD characteristics are shown in the following table (Temperature: 25°C, Relative Humidity: 40%).
Feint 6 Structure Specification 6 Structure Specification 6.1 Product Appearance The product appearance for FM101 module is shown in Figure 24: a so asses tenseness 9 seersucker Bu Figure 24. Module appearance e The label of each module is subject to the good shipped. 6.2 Dimension of Structure The structural dimension of the FM101 module is shown in Figure 25: Copyright © Flamenco Wireless inc.
Feint 6 Structure Specification Lo Bahia Bide Yio Figure 25. Dimension of structure 6.3 M.2 Interface Model The FM101 M.2 module adopts 75-pin gold finger as external interface, where 67 pins are signal pins and 8 pins are notch pins as shown in Figure 3. For module dimension, please refer to Figure 26 Dimension of Structure. Based on the M.2 interface definition, FM101 module adopts Type 3042-S-B interface the component maximum height on t top layer is 1.5 mm, PCB thickness is 0.8 mm, and KEY ID is B).
Feint 6 Structure Specification Module Nomenclatures. Sample type: 5042-5348 Cae Bess sensualist COIR 3 DHE A aE Semen Reed rte enn 0am 0008 (6010) ART FRR Lama Eun Mary intentness EMG 3 = a Gun Se Gite fia damn: Reseed for uli Use Anne Bose to Fuels ese i tin ine BBE Res mi TE afi sen peels Lie ONLY which a digestible sot is being speed FE Labs lidded In Reweigh anglophone HE Key is intended for custom use.
Feint 6 Structure Specification DING. ian Sr-syncope | HERE ELATES SESAME ALTERED Figure 27. M.2 Dimensions of structure for stack-up Mid-mount single-sided module BE BARE 3=0isk0ds ECE sre | 3 sai i) CENTS S49 Figure 28. M.2 dimensions of structure for stack-up top-mount single-sided module Copyright © Flamenco Wireless Inc.
Feint 6 Structure Specification 6.5 M.2 Card Assembly 6.5.1 Card Insertion Angled insertion is allowable and preferred; intent is to minimize the insertion and extraction force. The minimum angle of insertion is 5° . For APCI0144-PO01A, the maximum angle of insertion is 5°, For APCI0026-P001A, the maximum angle of insertion is 20°, Refer to Figure 29 and Figure 30 to insert and extract the module. Figure 29. Angle of insertion for APCI0144-PO01A gon 1.70 ll Figure 30.
Feint 6 Structure Specification i Tr asl along a we = slg no 22 iit Sle Nice Ea irs = Je SEL SEE be Mali { Y : Figure 31. Stack-up mid-mount single-sided module ; 2.4 mm maximum above mother board Suggest to cut the area of mother board under M.2 module 6.5.1 Top-mount Connection with Single-Sided Module Stack-up top-mount single-sided module is shown in Figure 32. The maximum height of components is 1.5 mm. {220MM Donn HT 2IBMAX ESS 14040.90 ABOVE BB DEMING z Bonn 4 fs Figure 32.
Feint 6 Structure Specification 2.75 mm maximum above mother board. Full keep out area below e module, which means don't place any components and routing below M.2 module. Add thermal pad between M.2 module and mother board for thermal dissipation. 6.6 Storage 6.6.1 Storage Life Storage Conditions (recommended): Temperature is 23 + 5°C, relative humidity is less than RH 60%. Storage period: Under the recommended storage conditions, the storage life is 12 months. 6.
Feint 6 Structure Specification held ER ENVELOPE Label Shrieking: 8 E00 ENGELS HE [{pier wide Figure 33. Tray packaging process 6.7.2 Tray Size The pallet size is 315 mm x 170 and is shown in Figure 34: Copyright © Flamenco Wireless Inc.
FiO BETA AL Figure 34. Tray size (unit: mm) 6 Structure Specification DETAIL ai ITEM DIM (Unit: mm) L Ww H T A B 31.003 C D E F Copyright © Flamenco Wireless Inc.
Interrogators Installation Manual Important Notice to OEM integrator 1. This module is limited to OEM installation ONLY. 2. This module is limited to installation in mobile or fixed applications, according to Part 3. The separate approval is required for all other operating configurations, including portable configurations with respect to Part 2.1093 and different antenna configurations 4. For FCC Part 15.
Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: {1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
This device is intended only for OEM integrator under the following conditions: (For module device use) 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required.
Industry Canada Statement This device complies with Industry Canada’s license-exempt Ross. Operation is subject to the following two conditions: {1) This device may not cause interference; and {2) This device must accept any interference, including interference that may cause undesired operation of the device. Le present apparel est conform aux CNR industrious Canada applicable aux apparels radio exempts de license.
Cet appareil est congru uniquement pour les intégrateurs OEM dans les conditions suivantes: (Pour utilisation de dispositif module) 1) L'antenne doit &tre installée de telle sorte qu'une distance de 20 cm est respectée entre I'antenne et les utilisateurs, et 2) Le module émetteur peut ne pas être implanté avec un autre émetteur ou antenne. Tant que les 2 conditions ci-dessus sont remplies, des essais supplémentaires sur 'émetteur ne seront pas nécessaires.
Manuel Information to the End User The OEM ingratement has to be acare not to protide information to the end user reginglard how to installe or rem ove shit RF module in the user's manuel of the end produit chichi intégrâtes shit module. The end user manuel hall incluse all redire dégueulatoire information/warning as show in shit manuel.
