User's Manual

BAP-AC1750
Quick Start Guide
Package contents
1 x BAP-AC1750
1 x BAP mounting bracket
1 x DC adapter (12V/2A)
1 x Quick Start Guide
1 x VIP card
Mounting accessories
4 x Truss head machine screws (Φ4mm)
4 x Jam nuts
4 x Flat washers
Extra accessories
4 x Round head drywall screw (Φ3mm)
4 x M.6 plastic anchors (Φ6.5mm)
Hardware features
NOTE: If any of the items is damaged or missing, contact ASUS for technical inquiries and
support.
Hardware installation
Requirements
• CAT5enetworkcableorbetter
• Drillanddrillbit(6.5mmforwall‐mountingor4mmforceiling‐mounting)
• Optional:Drywallorkeyholesaw(tocut25mmholefortheEthernetcablefeed)
Guidelines
Followtheseguidelinestogetthemaximumcoverage:
• PlaceyourBAP-AC1750inacentralizedarea.
• DonotinstallyourBAP-AC1750nearmetalobjectssuchasheatingducts,metal
doors, or electric service panels.
• IfyouareinstallingmorethanoneBAP-AC1750,placethemabout80feetapart.
• WhenyouinstallyourBAP-AC1750onapole,thecoverageis180degrees.
NOTE: Do not mount two BAP-AC1750s back to back on a pole to achieve a 360 degrees
coverage. The two BAP-AC1750 could interfere with each other.
Mounting options
Mounting your BAP-AC1750 to the
bracket and to the wall
1. Drill four 6.5mm holes on the wall.
2. Place four 6.5mm M6 plastic anchors in the
four holes.
3. Tighten the bracket to the wall with four
3mm round head drywall screws.
4. Align and install your BAP-AC1750 into the
bracket.
Mounting your BAP-AC1750 directly to the wall
1. Drilltwo6.5mmholesonthewallwithadistanceof281mmbetweeenthem.
2. Place two 6.5mm M6 plastic anchors in the two holes.
3. Tighten two 3mm round head drywall screws into the two M6 plastic anchors in
the holes.
4. Hang your BAP-AC1750 into the two screws on the wall.
Securing your BAP-AC1750
1. Locate the Kensington
security slot on your BAP-
AC1750.
2. Insert a Kensington lock
into the security slot and
secure it to an immovable
object.
Connecting the power supply
YoucanconnecteitherthebundledDCadapteroran802.3atpowersourcetoyour
BAP-AC1750.
Via the DC adapter
Via a PoE compliant power source
IMPORTANT! UseonlytheDCadapterthatcamewithyourpackageoran802.3atcompliant
PoE power source. Using other DC adapters may damage your BAP-AC1750.
NOTES:
• WhenboththeDCadapterandPoEpowersourcearepluggedtoyourBAP-AC1750,the
DCpoweristheprimarysourceofyourBAP-AC1750.WhentheDCpowerfails,yourBAP-
AC1750changestothe802.3atPoEsource.
• BAP-AC1750canbepoweredby802.3atcompliant(25.5W)PoEswitch/PoEinjectoror
802.3afcompliant(12.95W)PoEswitch/PoEinjector.WhenyourBAP-AC1750isoperated
on802.3afpower,theUSBportisdisabled,andtheTXpowerreduces3dBfrompowerby
802.3at.
• Environment Specications:
Temperature -5°Cto50degrees°C(OperatingTemperature)
-20°C to 70°C (Storage Temperature)
Operating humidity -5%to95%(Noncondensing)
19 20 21 22 23 24
13 14 15 16 17 18
7 8 9 10 11 12
1 2 3 4 5 6
Standard Switch
1.
Ethernet LED
Solid green: Ethernet cable is connected, but no data transmission.
Quick ashing green: Ethernet cable is connected, and data is transmitting.
2.
PoE LED
Solid green: Ethernet cable is connected, but no data transmission.
Quick ashing green: Ethernet cable is connected, and data is transmitting.
3.
5GHz / 2.4GHz LED
Solid green:Wi-Fiisready.
Quick ashing green:TransmittingorreceivingdataviaWi-Ficonnection.
4.
Power LED
Solid green: BAP-AC1750 is ready.
Slow ashing green
•BAP-AC1750istryingtoreachtheaccesscontroller.
•BAP-AC1750isupdatingitsrmware.
•BAP-AC1750isresettingtoitsdefaultsettings.
Quick ashing red
•BAP-AC1750iseitherinanuninitializedstate,orcannotreachtheaccesscontroller.
NOTE:WhenpowerLEDisoandalltheotherLEDsaresolidlylitup,thisindicatesthatthecontroller
daemon(CAPWAP)crashed.
5.
Kensington security slot
Insert a Kensington lock into this hole to keep your BAP-AC1750 safe.
6.
Power (DC-IN) port
Insert the bundled DC adapter into this port and connect to a power source.
7.
Reset button
This button resets or restores the system to its factory default settings.
8.
USB port
Insert a USB device such as a USB ash drive into the port.
9.
Ethernet (LAN) port
Connect a network cable into this port to establish Ethernet connection.
10.
PoE port
Insert a network cable into this port to establish Ethernet connection and provide DC power input.
Unmounting your BAP-AC1750
Press the notch on the bracket to
unmount your BAP-AC1750.
E12038/FirstEdition/October2016
On the ceiling tile
1. WhentheT-barwidthismorethan24mmorhasarevealedgetreatment,drill
four holes on the tile.
2. Cut about 25 mm rectangular hole on the tile for the Ethernet cable feed.
3. Attach the bracket to the tile with the four bundled truss head machine screws.
4. Tightenthebrackettothetilewiththefourbundledjamnutsandatwashers.
5. Align and install your BAP-AC1750 into the bracket.
128mm
Mounting to the ceiling
You can mount your BAP-AC1750 to the ceiling either on the ceiling tile rail (T-bar) or
on the ceiling tile.
On the T-bar rail
1. OntheinstalledT-barrailonthe
ceiling, install the bundled bracket
through the T-bar holder. The AP
weight is sustained by the clamp.
NOTE: The bundled bracket supports the
T-bar width up to 24mm.
2. Install your BAP-AC1750 into the
bracket.
wall
19 20 21 22 23 24
13 14 15 16 17 18
7 8 9 10 11 12
1 2 3 4 5 6
Standard Switch
POE Injector
19 20 21 22 23 24
13 14 15 16 17 18
7 8 9 10 11 12
1 2 3 4 5 6
POE Switch
POE Switch
OR
E12038_BAP-AC1750_QSG.indd 1 2016/11/1 17:10:30