User's Manual
Table Of Contents
- 1 Introduction
- NOTE:
- NOTE:
- 2 Product Architecture
- 3 Electrical Specifications
- 4 Mechanical Specifications
- 5 Performance
- 1. BT in SW RF-KILL in all the tests
- 2. HB values refer to internal FE SKU
- 3. OS: Win10
- 1. Wi-Fi in SW RF-KILL in all the tests
- 2. OS: Win10
- 3. WsP is Master device
- 1. The TX power per MCS relate to IEEE, mask compliance and limited by regulatory TX power limits.
- 2. The values relate to internal FE SKU
- 3. The values are for typical device and typical conditions
- 1. Measured at ANT port
- 2. Typical means Nominal corner, AVG over non BE CHs. AVG over freq segment and chains
- 3. Max means over PVT
- NOTE: The throughput values relate to Intel® Skylake Platform and CPU, Single User.
- 6 Thermal Specifications
- 7 Regulatory
- 8 Dynamic Regulatory Solution
- 9 Platform Design Guidelines
- 9.1 Socket 1 key options for 2230 cards
- 9.1.1 Socket 1 Hybrid Key E scheme
- 9.1.2 Connectorized Hybrid Key E (2230) pin-out
- 9.1.3 Special considerations for the Hybrid Key E scheme
- 9.1.4 Soldered-down (1216) pin-out
- 9.1.5 Breakout example for JfP soldered-down module
- 9.1.6 Signal connection pitfalls
- 9.1.7 Pullups and pulldowns
- 9.1.8 IO connection scenarios and best practices
- 9.1.9 I/F specific guidelines
- 9.1.10 Connectivity module power control
- 9.1.11 Power supply de-coupling
- 9.1.12 Wi-Fi wireless disable and HW RF-KILL
- 9.1.13 M.2 Bluetooth HW RF-KILL
- 9.1.14 BIOS
- 9.1 Socket 1 key options for 2230 cards
peuvent créer des interférences avec ce produit et/ou lui être nuisible. Le gain d'antenne maximum
permissible pour
une utilisation avec ce produit est de 6 dBi afin d'être conforme aux limites de puissance isotropique
rayonnée
équivalente (P.I.R.E.) applicable dans les bandes 5.25-5.35 GHz et 5.725-5.85 GHz en
fonctionnement point-àpoint.
Pour se conformer aux conditions d'exposition de RF toutes les antennes devraient être localisées à
une
distance minimum de 20 cm, ou la distance de séparation minimum permise par l'approbation du
module, du corps
de toutes les personnes.
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a
type and
maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential
radio interference
to other users, the antenna type and its gain should be so chosen that the equivalent isotropically
radiated power
(e.i.r.p.) is not more than that necessary for successful communication.
Selon les règlements de Canada d'Industrie, cet émetteur de radio peut seulement fonctionner en
utilisant une
antenne du type et de gain maximum (ou moindre) que le gain approuvé pour l'émetteur par Canada
d'Industrie.
Pour réduire lesinterférences radio potentielles avec les autres utilisateurs, le type d'antenne et son
gain devraient
être choisis de façon à ce que la puissance isotrope rayonnée équivalente(P.I.R.E.) ne soit pas
supérieure à celle qui
est nécessaire pour une communication réussie.
Safety Approval Considerations
This device has been safety approved as a component and is for use only in complete equipment
where the acceptability of the combination is determined by the appropriate safety agencies. When
installed, consideration must be given to the following:
It must be installed into a compliant host device meeting the requirement of UL/EN/IEC 60950-1 2nd
edition including the general provisions of enclosure design 1.6.2 and specifically paragraph 1.2.6.2
(Fire Enclosure).
The device shall be supplied by a SELV source when installed in the end-use equipment.
A heating test shall be considered in the end-use product for meeting the requirement of UL/EN/IEC
60950-1 2nd edition.