User's Manual
Table Of Contents
- 1 Introduction
- NOTE:
- NOTE:
- 2 Product Architecture
- 3 Electrical Specifications
- 4 Mechanical Specifications
- 5 Performance
- 1. BT in SW RF-KILL in all the tests
- 2. HB values refer to internal FE SKU
- 3. OS: Win10
- 1. Wi-Fi in SW RF-KILL in all the tests
- 2. OS: Win10
- 3. WsP is Master device
- 1. The TX power per MCS relate to IEEE, mask compliance and limited by regulatory TX power limits.
- 2. The values relate to internal FE SKU
- 3. The values are for typical device and typical conditions
- 1. Measured at ANT port
- 2. Typical means Nominal corner, AVG over non BE CHs. AVG over freq segment and chains
- 3. Max means over PVT
- NOTE: The throughput values relate to Intel® Skylake Platform and CPU, Single User.
- 6 Thermal Specifications
- 7 Regulatory
- 8 Dynamic Regulatory Solution
- 9 Platform Design Guidelines
- 9.1 Socket 1 key options for 2230 cards
- 9.1.1 Socket 1 Hybrid Key E scheme
- 9.1.2 Connectorized Hybrid Key E (2230) pin-out
- 9.1.3 Special considerations for the Hybrid Key E scheme
- 9.1.4 Soldered-down (1216) pin-out
- 9.1.5 Breakout example for JfP soldered-down module
- 9.1.6 Signal connection pitfalls
- 9.1.7 Pullups and pulldowns
- 9.1.8 IO connection scenarios and best practices
- 9.1.9 I/F specific guidelines
- 9.1.10 Connectivity module power control
- 9.1.11 Power supply de-coupling
- 9.1.12 Wi-Fi wireless disable and HW RF-KILL
- 9.1.13 M.2 Bluetooth HW RF-KILL
- 9.1.14 BIOS
- 9.1 Socket 1 key options for 2230 cards
Consult the dealer or an experienced radio/TV technician for help.
NOTE: The adapter must be installed and used in strict accordance with the manufacturer's
instructions
as described in the user documentation that comes with the product. Any other installation or use
will violate FCC Part 15 regulations.
Canada – Industry Canada (IC)
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to
the following two
conditions: (1) this device may not cause interference, and (2) this device must accept any
interference, including
interference that may cause undesired operation of the device.
Cet appareil se conforme aux normes Canada d'Industrie de RSS permis-exempt. L'utilisation est
assujetti aux deux
conditions suivantes: (1) cet appareil ne peut pas causer d'interférences, et (2) cet appareil doit
accepter des
interférences , y compris des interférences qui peuvent causer desopérations non désirées de
l'appareil.
Caution: When using IEEE 802.11a wireless LAN, this product is restricted to indoor use due to its
operation in the
5.15- to 5.25-GHz frequency range. Industry Canada requires this product to be used indoors for the
frequency range of 5.15GHz to 5.25GHz to reduce the potential for harmful interference to
co-channel mobile satellite systems.
High power radar is allocated as the primary user of the 5.25- to 5.35-GHz and 5.65 to 5.85-GHz
bands. These radar stations can cause interference with and/or damage to this device. The
maximum allowed antenna gain for
use with this device is 6dBi in order to comply with the E.I.R.P limit for the 5.25- to 5.35 and 5.725
to 5.85GHz frequency range in point-to-point operation. To comply with RF exposure requirements
all antennas should be located at a minimum distance of 20cm, or the minimum separation distance
allowed by the module approval, from the body of all persons.
Attention: l'utilisation d'un réseau sans fil IEEE802.11a est restreinte à une utilisation en intérieur à
cause du
fonctionnement dans la bande de fréquence 5.15-5.25 GHz. Industry Canada requiert que ce produit
soit utilisé à
l'intérieur des bâtiments pour la bande de fréquence 5.15-5.25 GHz afin de réduire les possibilités
d'interférences
nuisibles aux canaux co-existants des systèmes de transmission satellites. Les radars de puissances
ont fait l'objet
d'une allocation primaire de fréquences dans les bandes 5.25-5.35 GHz et 5.65-5.85 GHz. Ces
stations radar