User's Manual
Table Of Contents
- 1 Introduction
- NOTE:
- NOTE:
- 2 Product Architecture
- 3 Electrical Specifications
- 4 Mechanical Specifications
- 5 Performance
- 1. BT in SW RF-KILL in all the tests
- 2. HB values refer to internal FE SKU
- 3. OS: Win10
- 1. Wi-Fi in SW RF-KILL in all the tests
- 2. OS: Win10
- 3. WsP is Master device
- 1. The TX power per MCS relate to IEEE, mask compliance and limited by regulatory TX power limits.
- 2. The values relate to internal FE SKU
- 3. The values are for typical device and typical conditions
- 1. Measured at ANT port
- 2. Typical means Nominal corner, AVG over non BE CHs. AVG over freq segment and chains
- 3. Max means over PVT
- NOTE: The throughput values relate to Intel® Skylake Platform and CPU, Single User.
- 6 Thermal Specifications
- 7 Regulatory
- 8 Dynamic Regulatory Solution
- 9 Platform Design Guidelines
- 9.1 Socket 1 key options for 2230 cards
- 9.1.1 Socket 1 Hybrid Key E scheme
- 9.1.2 Connectorized Hybrid Key E (2230) pin-out
- 9.1.3 Special considerations for the Hybrid Key E scheme
- 9.1.4 Soldered-down (1216) pin-out
- 9.1.5 Breakout example for JfP soldered-down module
- 9.1.6 Signal connection pitfalls
- 9.1.7 Pullups and pulldowns
- 9.1.8 IO connection scenarios and best practices
- 9.1.9 I/F specific guidelines
- 9.1.10 Connectivity module power control
- 9.1.11 Power supply de-coupling
- 9.1.12 Wi-Fi wireless disable and HW RF-KILL
- 9.1.13 M.2 Bluetooth HW RF-KILL
- 9.1.14 BIOS
- 9.1 Socket 1 key options for 2230 cards
REGULATORY INFORMATION
USA - Federal Communications Commission (FCC)
This wireless adapter is restricted to indoor use due to its operation in the 5.15 to 5.25 and 5.470 to
5.75GHz frequency ranges. No configuration controls are provided for Intel® wireless adapters
allowing any change in the frequency of operations outside the FCC grant of authorization for U.S.
operation according to Part 15.407 of the FCC rules.
Intel® wireless adapters are intended for OEM integrators only.
Intel® wireless adapters cannot be co-located with any other transmitter unless approved by the
FCC.
This wireless adapter complies with Part 15 of the FCC Rules. Operation of the device is subject to
the following two conditions:
This device may not cause harmful interference.
This device must accept any interference that may cause undesired operation.
NOTE: The radiated output power of the adapter is far below the FCC radio frequency exposure
limits.
Nevertheless, the adapter should be used in such a manner that the potential for human contact
during normal operation is minimized. To avoid the possibility of exceeding the FCC radio frequency
exposure limits, you should keep a distance of at least 20cm between you (or any other person in the
vicinity), or the minimum separation distance as specified by the FCC grant conditions, and the
antenna that is built
into the computer. Details of the authorized configurations can be found at
http://www.fcc.gov/oet/ea/
by entering the FCC ID number on the device.
Class B Device Interference Statement
This wireless adapter has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This wireless adapter generates, uses, and
can radiate radio frequency energy. If the
wireless adapter is not installed and used in accordance with the instructions, the wireless adapter
may cause harmful interference to radio communications. There is no guarantee, however, that
such interference will not occur in a particular installation. If this wireless adapter does cause
harmful interference to radio or television reception
(which can be determined by turning the equipment off and on), the user is encouraged to try to
correct the interference by taking one or more of the following measures:
Reorient or relocate the receiving antenna of the equipment experiencing the interference.
Increase the distance between the wireless adapter and the equipment experiencing the
interference.
Connect the computer with the wireless adapter to an outlet on a circuit different from that to which
the equipment experiencing the interference is connected.