User's Manual
Table Of Contents
- 1 Introduction
- NOTE:
- NOTE:
- 2 Product Architecture
- 3 Electrical Specifications
- 4 Mechanical Specifications
- 5 Performance
- 1. BT in SW RF-KILL in all the tests
- 2. HB values refer to internal FE SKU
- 3. OS: Win10
- 1. Wi-Fi in SW RF-KILL in all the tests
- 2. OS: Win10
- 3. WsP is Master device
- 1. The TX power per MCS relate to IEEE, mask compliance and limited by regulatory TX power limits.
- 2. The values relate to internal FE SKU
- 3. The values are for typical device and typical conditions
- 1. Measured at ANT port
- 2. Typical means Nominal corner, AVG over non BE CHs. AVG over freq segment and chains
- 3. Max means over PVT
- NOTE: The throughput values relate to Intel® Skylake Platform and CPU, Single User.
- 6 Thermal Specifications
- 7 Regulatory
- 8 Dynamic Regulatory Solution
- 9 Platform Design Guidelines
- 9.1 Socket 1 key options for 2230 cards
- 9.1.1 Socket 1 Hybrid Key E scheme
- 9.1.2 Connectorized Hybrid Key E (2230) pin-out
- 9.1.3 Special considerations for the Hybrid Key E scheme
- 9.1.4 Soldered-down (1216) pin-out
- 9.1.5 Breakout example for JfP soldered-down module
- 9.1.6 Signal connection pitfalls
- 9.1.7 Pullups and pulldowns
- 9.1.8 IO connection scenarios and best practices
- 9.1.9 I/F specific guidelines
- 9.1.10 Connectivity module power control
- 9.1.11 Power supply de-coupling
- 9.1.12 Wi-Fi wireless disable and HW RF-KILL
- 9.1.13 M.2 Bluetooth HW RF-KILL
- 9.1.14 BIOS
- 9.1 Socket 1 key options for 2230 cards
Electrical Specifications
Intel
®
Wireless-AC 9560 (Jefferson Peak)
External Product Specification (EPS) April 2017
22 Intel Confidential Document Number: 567240–1.0
Pin # Pin name Function when CNVi
is used
Function when Standard
(discrete) M.2 is used
Comments
A42 RF_RESET_B RF_RESET_B Not Applicable Can be connected to 58
on the Motherboard
A43 CLKREQ0 CLKREQ0 Not Applicable Can be connected to 59
on the Motherboard
A44 REFCLK0 REFCLK0 Not Applicable
A45 NO CONNECT NO CONNECT Not Applicable Pin must be left floating
A46 RESERVED RESERVED Not Applicable Not connected
A47 RESERVED RESERVED Not Applicable Not connected
A48 3.3V 3.3V Not Applicable
A49 3.3V 3.3V Not Applicable
A50 GND GND Not Applicable
3.2 Input/output electrical specifications
Table 3-3 Input/Output electrical specifications
I/O type
Symbol Parameter Min Max Unit Notes
1.8V I/O
RF_RESET_B
V
IH
Input High Voltage
1.26
2.1
V
V
IL
Input Low Voltage
-0.3
0.54
V
R
PU/PD
Weak Pull-Up or Pull-
Down
70 150 Kohm
I
IN
Input Leakage Current
10
uA
No Pull Up/Down
V
OH
Output High Voltage 1.62 1.8 V Io = 2mA
Load = 20pF
V
OL
Output Low Voltage 0 0.18 Io = 2mA
Load = 20pF
T
R
, T
F
Rise, Fall Time
6
ns
Load = 20pF
C
IO
IO Pin Capacitance
2
pF
1.8V FS I/O
A4WP_IRQ#
A4WP_I2C_CLK
A4WP_I2C_CLK
(Note 1)
V
IH
Input High Voltage
1.26
2.1
V
V
IL
Input Low Voltage
-0.3
0.54
V
R
PU/PD
Weak Pull-Up or Pull-
Down
100 180 Kohm
I
IN
Input Leakage Current
10
uA
No Pulls
V
OL
Push-Pull
Output Low Voltage
Push-pull
0 0.36 Io = 2mA
Load = 50pF
V
OH
Push-Pull
Output Low Voltage
Push-pull
1.62 1.8 Io = 2mA
Load = 50pF
T
R
, T
F
Push-Pull
Rise, Fall Time
Push-pull
18.5 ns Load = 50pF