R VX97 Pentium Motherboard USER'S MANUAL
USER'S NOTICE No part of this manual, including the products and softwares described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. (“ASUS”).
ASUS CONTACT INFORMATION ASUSTeK COMPUTER INC. Marketing Info: Address: 150 Li-Te Road, Peitou, Taipei, Taiwan, ROC Telephone: 886-2-894-3447 Fax: 886-2-894-3449 Email: info@asus.com.tw Technical Support: Fax: BBS: Email: WWW: Gopher: FTP: 886-2-895-9254 886-2-896-4667 tsd@asus.com.tw http://www.asus.com.tw/ gopher.asus.com.tw ftp.asus.com.
CONTENTS I. INTRODUCTION ........................................................................... How this manual is organized .......................................................... Item Checklist .................................................................................. II. FEATURES .................................................................................... Features of the VX97 Motherboard ................................................. Parts of the VX97 Motherboard ..............
CONTENTS Load Setup Defaults ................................................................... Supervisor Password and User Password .................................. IDE HDD Auto Detection .......................................................... Save and Exit Setup ................................................................... Exit Without Saving ................................................................... V. DESKTOP MANAGEMENT ........................................................
FCC & DOC COMPLIANCE Federal Communications Commission Statement This device complies with FCC Rules Part 15. Operation is subject to the following two conditions: • • This device may not cause harmful interference, and This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
I. INTRODUCTION I. INTRODUCTION (Manual / Checklist) How this manual is organized This manual is divided into the following sections: I. Introduction: II. Features: III. Installation: IV. BIOS Setup: V. Software: VI. ASUS SCSI: VII. ASUS I-A16C: VIII. DOS/Win3.1x: IX. Windows 95: Manual information and checklist Information and specifications concerning this product Instructions on setting up the motherboard BIOS software setup information.
II. FEATURES Features of the VX97 Motherboard The ASUS VX97 is carefully designed for the demanding PC user who wants a great many features in a small package. This motherboard: • Intel Chipset: Features Intel's 430VX PCIset with I/O subsystems. • II. FEATURES (Features) • 8 Versatile Processor Support: Intel Pentium® 75-233MHz (P55C-MMX™, P54C/ P54CS), IBM®/Cyrix® 6x86-PR166+ (Rev 2.7 or later), IBM®/Cyrix® 6x86MX™ (PR166 & above), AMD-K5™ (PR75-PR133), AMD-K6™ (PR166-PR233).
II. FEATURES Parts of the VX97 Motherboard Programmable Flash ROM Super Multi-I/O Serial/Parallel Ports II.
III. INSTALLATION Map of the VX97 Motherboard PS/2 Mouse Universal Serial Bus (Reserved) Keyboard Keyboard BIOS Serial Ports Flash ROM for BIOS ISA Slot 1 COM 2 Parallel Port (Printer) Board Power Input P9 P8 SIMM Socket 4 (Bank 1) SIMM Socket 3 (Bank 1) SIMM Socket 2 (Bank 0) SIMM Socket 1 (Bank 0) Secondary IDE Primary IDE Floppy Drives PCI Slot 1 III.
III. INSTALLATION Jumpers 1) 2) 3) 4) 5) BBLKW RTCLR / JP1 VID0, 1, 2 FS0, FS1, FS2 BF0, BF1 p. 13 p. 13 p. 14 p. 15 p. 15 Flash ROM Boot Block Program (Disable/Enable) Real Time Clock RAM / Battery Test Lead CPU Voltage Selection CPU External Clock (BUS) Frequency Selection CPU:BUS Frequency Ratio p. 16 p. 18 p. 19 p. 19 72-Pin DRAM Memory Expansion Sockets Central Processing Unit (CPU) Socket 16-bit ISA Bus Expansion Slots 32-bit PCI Bus Expansion Slots p. 21 p. 21 p. 22 p. 22 p. 23 p. 23 p. 24 p.
III. INSTALLATION Installation Steps Before using your computer, you must complete the following steps: 1. 2. 3. 4. 5. 6. Set Jumpers on the Motherboard Install Memory Modules Install the Central Processing Unit (CPU) Install Expansion Cards Connect Ribbon Cables, Cabinet Wires, and Power Supply Setup the BIOS Software 1. Jumpers III. INSTALLATION (Jumpers) Several hardware settings are made through the use of jumper caps to connect jumper pins (JP) on the motherboard.
III. INSTALLATION Jumper Settings 1. Flash ROM Boot Block Programming (BBLKW) This sets the operation mode of the boot block area of the Programmable Flash ROM to allow programming in the Enabled position. This is required only if prompted by the Flash Memory Writer Utility as shown in BIOS SOFTWARE. BBLKW [1-2] (Default) [2-3] BBLKW 1 2 3 Disabled / Protected (Default) BBLKW 1 2 3 III. INSTALLATION (Jumpers) Programming Disabled Enabled Enabled Boot Block Programming (Disable / Enable) 2.
III. INSTALLATION 3. Voltage Regulator Output Selection (VID0, 1, 2) These jumpers set the voltage supplied to the CPU. The voltage regulators will automatically detect and switch between Single Power Plane & Dual Power Planes. WARNING! Incorrect settings can damage your CPU. If you are not absolutely clear on CPU jumper settings, check with your retailer.
III. INSTALLATION 4. CPU External (BUS) Frequency Selection (FS0, FS1, FS2) These jumpers tell the clock generator what frequency to send to the CPU. These allow the selection of the CPU’s External frequency (or BUS Clock). The BUS Clock times the BUS Ratio equals the CPU's Internal frequency (the advertised CPU speed). 5. CPU to BUS Frequency Ratio (BF0, BF1) These jumpers set the frequency ratio between the Internal frequency of the CPU and the External frequency (called the BUS Clock) within the CPU.
III. INSTALLATION 2. System Memory This motherboard supports four 72-pin SIMMs (Single Inline Memory Modules) of 4MB, 8MB, 16MB, or 32MB to form a memory size between 8MB to 128MB. The DRAM can be either 60ns or 70ns Fast Page Mode (FPM) (Asymmetric or Symmetric) or Enhanced Data Output (EDO). SIMMs must be installed in pairs so that each bank contains two of the same size memory modules. Maximum memory size of SIMM’s must be 128MB or less.
III. INSTALLATION DRAM Memory Installation Procedures: 1. The SIMM memory modules will only fit in one orientation as shown because of a "Plastic Safety Tab" on one end of the SIMM slots which requires the "Notched End" of the SIMM memory modules. 1 2 3 4 DRAM Memory Module Example Notched End Bank 1 III. INSTALLATION (System Memory) 72 Pin SIMM Sockets Bank 0 2. Press the memory module firmly into place starting from a 45 degree angle making sure that all the contacts are aligned with the socket. 3.
III. INSTALLATION 3. Central Processing Unit (CPU) The motherboard provides a 321-pin ZIF Socket 7 that is backwards compatible with ZIF Socket 5 processors. The CPU that came with the motherboard should have a fan attached to it to prevent overheating. If this is not the case then purchase a fan before you turn on your system. Apply thermal jelly to the CPU top and then install the fan onto the CPU.
III. INSTALLATION 4. Expansion Cards WARNING: Make sure that you unplug your power supply when adding or removing expansion cards or other system components. Failure to do so may cause severe damage to both your motherboard and expansion cards. First read your expansion card documentation on any hardware and software settings that may be required to setup your specific card. NOTE: PCI Slot 4 has a MediaBus extension 2.
III. INSTALLATION Both ISA and PCI expansion cards may need to use IRQs. System IRQs are available to cards installed in the ISA expansion bus first, and any remaining IRQs are then used by PCI cards. Currently, there are two types of ISA cards. The original ISA expansion card design, now referred to as “Legacy” ISA cards, requires that you configure the card’s jumpers manually and then install it in any available slot on the ISA bus. You may use Microsoft's Diagnostic (MSD.
III. INSTALLATION 5. External Connectors WARNING: Some pins are used for connectors or power sources. These are clearly separated from jumpers in "Map of the ASUS Motherboard" on page 4. Placing jumper caps over these will cause damage to your motherboard. IMPORTANT: Ribbon cables should always be connected with the red stripe on the Pin 1 side of the connector. The four corners of the connectors are labeled on the motherboard.
III. INSTALLATION 3. Parallel Printer Connector (26 Pin Block) Connection for the included parallel port ribbon cable with mounting bracket. Connect the ribbon cable to this connection and mount the bracket to the case on an open slot. It will then be available for a parallel printer cable. You can enable the parallel port and choose the IRQ through "Onboard Parallel Port" in Chipset Features of the BIOS SOFTWARE.
III. INSTALLATION 5. Floppy drive connector (34-pin block ) This connector supports the provided floppy drive ribbon cable. After connecting the single end to the board, connect the two plugs on the other end to the floppy drives. (Pin 5 is removed to prevent inserting in the wrong orientation when using ribbon cables with pin 5 plugged). Pin 1 Connect the Red stripe to Pin 1 III. INSTALLATION (Connectors) Floppy Drive Connector 6.
III. INSTALLATION 7. Primary / Secondary IDE connectors (Two 40-pin Block) These connectors support the provided IDE hard disk ribbon cable. After connecting the single end to the board, connect the two plugs at the other end to your hard disk(s). If you install two hard disks, you must configure the second drive to Slave mode by setting its jumper accordingly. Please refer to the documentation of your hard disk for the jumper settings.
III. INSTALLATION 9. Turbo LED Lead (PANEL) The motherboard's turbo function is always on. The turbo LED connection is labeled here but the LED will remain constantly lit while the system power is on. You may wish to connect the Power LED from the system case to this lead. See the figure below. III. INSTALLATION (Connectors) 10.
III. INSTALLATION 14. IrDA-compliant infrared module connector (IR) This connector supports the optional wireless transmitting and receiving infrared module. This module mounts to a small opening on system cases that support this feature. You must also configure the setting through "UART2 Use Infrared" in Chipset Features Setup to select whether UART2 is directed for use with COM2 or IrDA.
III. INSTALLATION Power Connection Procedures 1. After all jumpers and connections are made, close the system case cover. 2. Make sure that all switches are in the off position as marked by . 3. Connect the power supply cord into the power supply located on the back of your system case as instructed by your system user's manual. 4. Connect all power cords into a power strip that is equipped by a surge protector. 5. You may then turn on your devices in the following order: a. Your monitor b.
IV. BIOS SOFTWARE Support Software FILELIST.TXT - View this file to see the files included in the support software. PFLASH.EXE - This is the Flash Memory Writer utility that updates the BIOS by uploading a new BIOS file to the programmable flash ROM chip on the motherboard. To determine the BIOS version, check the last four numbers of the code displayed on the upper left-hand corner of your screen during bootup. Larger numbers represent a newer BIOS file.
IV. BIOS SOFTWARE 2. Update BIOS Main Block from File This option updates the BIOS from a file on the disk. This can either be a new file or a backup file created by the “Save Current BIOS to File” option. This will not update the Boot Block if the Boot Block is different. You will be prompted with the following if advanced features if necessary. Boot Block of New BIOS is different from old one !!! Please Use 'Advanced Feature' to flash whole bios !!! 3.
IV. BIOS SOFTWARE Updating your Motherboard's BIOS 1. Download an updated BIOS file from Bulletin Board Services (BBS) or the internet (WWW) and save to the diskette you created in step 1 of the Main Menu. See ASUS CONTACT INFORMATION on page II. 2. Turn off your computer and open the system cabinet to Enable "Boot Block Programming" jumper as shown in section III. 2. Boot from the floppy diskette you created in step 1 of the main menu. 3. At the "A:\" prompt, type: PFLASH 4.
