Quick Start Guide
Regulatory notices
REACH
Complying with the REACH (Registration, Evaluation, Authorization, and
Restriction of Chemicals) regulatory framework, we publish the chemical
substances in our products at ASUS REACH website at http://csr.asus.com/
english/REACH.htm
RF exposure warning
This equipment must be installed and operated in accordance with provided
instructions and the antenna(s) used for this transmitter must be installed
to provide a separation distance of at least 20 cm from all persons and
must not be co-located or operating in conjunction with any other antenna
or transmitter. End-users and installers must be provide with antenna
installation instructions and transmitter operating conditions for satisfying
RF exposure compliance.
France Restricted Wireless Frequency Bands
Some areas of France have a restricted frequency band. The worst case
maximum authorized power indoors are:
• 10mWfortheentire2.4GHzband(2400MHz–2483.5MHz)
• 100mWforfrequenciesbetween2446.5MHzand2483.5MHz
NOTE:Channels10through13inclusiveoperateintheband2446.6MHz
to2483.5MHz.
There are few possibilities for outdoor use: On private property or on
the private property of public persons, use is subject to a preliminary
authorization procedure by the Ministry of Defense, with maximum
authorizedpowerof100mWinthe2446.5–2483.5MHzband.Useoutdoors
on public property is not permitted.
In the departments listed below, for the entire 2.4 GHz band:
• Maximumauthorizedpowerindoorsis100mW
• Maximumauthorizedpoweroutdoorsis10mW
Departmentsinwhichtheuseofthe2400–2483.5MHzbandispermitted
with an EIRP of less than 100mW indoors and less than 10mW outdoors:
01 Ain 02 Aisne 03 Allier
05 Hautes Alpes 08 Ardennes 09 Ariège
11 Aude 12 Aveyron 16 Charente
24 Dordogne 25 Doubs 26 Drôme
32 Gers 36 Indre 37 Indre et Loire
41 Loir et Cher 45 Loiret 50 Manche
55 Meuse 58 Nièvre 59 Nord
60 Oise 61 Orne 63 Puy du Dôme
64 Pyrénées
Atlantique
66 Pyrénées
Orientales
67 Bas Rhin
70 Haute Saône 71 Saône et Loire 75 Paris
82 Tarn et
Garonne
84 Vaucluse 88 Vosges
89 Yonne 90 Territoire de
Belfort
94 Val de Marne
This requirement is likely to change over time, allowing you to use your
wireless LAN card in more areas within France. Please check with ART for the
latest information (www.art-telecom.fr)
NOTE: Your WLAN Card transmits less than 100mW, but more than
10mW.
CE Mark Warning
CE marking for devices without wireless LAN/Bluetooth
The shipped version of this device complies with the requirements of
theEMCdirectives2004/108/EC(replacedinApril2016by2014/30/EU)
“Electromagneticcompatibility”and2006/95/EC(replacedinApril2016by
2014/35/EU)“Lowvoltagedirective”.
CE marking for devices with wireless LAN/ Bluetooth
ThisequipmentcomplieswiththerequirementsofDirective1999/5/EC
(replacedin2017byRED2014/53/EU)oftheEuropeanParliamentand
Commissionfrom9March,1999governingRadioandTelecommunications
Equipment and mutual recognition of conformity.
Regional notice for Singapore
This ASUS product complies with IDA Standards.
Complies with
IDA Standards
DB103778
Wireless Operation Channel for Different
Domains
N. America 2.412-2.462GHz Ch01 through CH11
Japan 2.412-2.484GHz Ch01 through Ch14
Europe ETSI 2.412-2.472 GHz Ch01 through Ch13
ASUS Contact Information
ASUSTeK COMPUTER INC.
Address 4F,No.150Li-TeRoad,Peitou,Taipei112,Taiwan
Telephone +886-2-2894-3447
Fax +886-2-2890-7798
Website
http://www.asus.com
Technical Support
Telephone +86-21-38429911
Fax +86-21-58668722,ext.9101#
Online support
http://qr.asus.com/techserv
ASUS COMPUTER INTERNATIONAL (America)
Address 800CorporateWay,Fremont,CA94539,USA
Telephone +1-510-739-3777
Fax +1-510-608-4555
Website
http://usa.asus.com
Technical Support
Support fax +1-812-284-0883
General support +1-812-282-4555
Online support
http://qr.asus.com/techserv
ASUS COMPUTER GmbH (Germany and Austria)
Address HarkortStr.21-23,D-40880Ratingen,Germany
Fax +49-2102-959931
Website
http://www.asus.com/de
Technical Support
Telephone +49-2102-5789555
Support Fax +49-2102-959911
Online support
http://qr.asus.com/techserv
Safety information
Your VivoStick is designed and tested to meet the latest standards of safety
for information technology equipment. However, to ensure your safety, it is
important that you read the following safety instructions.
Setting up your system
• Readandfollowallinstructionsinthedocumentationbeforeyou
operate your system.
• Donotusethisproductnearwateroraheatedsource.
• Makesureyouleaveplentyofspacearoundthesystemforventilation.
• Usethisproductinenvironmentswithambienttemperaturesbetween
1˚C(33.8˚F)and35˚C(95˚F).
• Ifyouuseanextensioncord,makesurethatthetotalampererating
of the devices plugged into the extension cord does not exceed its
ampere rating.
• Ifyounoticeanyofthefollowingconditions(orifyouhaveother
safety concerns), do not use your device: crackling, hissing, popping
sound, or a strong odor or smoke coming from your device. It is normal
for these conditions to appear when an internal electronic component
fails in a safe and controlled manner. However, these conditions may
also indicate a potential safety issue. Do not assume that it is a safe
failure. Turn off your device. If your device is plugged in, disconnect it
from its power source, and contact technical support for assistance.
• Magnet: Avoid placing any media that contains magnets or is
sensitive to magnetism, such as credit cards, bank cards, audio/video,
tapes, or magnetic memory devices, near your device as you may
lose information stored on that media and devices may be severely
damaged. Media containing information sensitive to magnets should
bekeptatleast5cmawayfromyourdevice.
• Pacemakers and other implanted medical devices: VivoStick
receives and transmits using Wi-Fi and Bluetooth technology, which
can interfere with pacemakers and other implanted medical devices. If
you have a pacemaker or other implanted medical device, contact your
physician or medical device manufacturer to make sure it’s okay to use
your VivoStick.
DO NOT throw the VivoStick in municipal waste. This product has
been designed to enable proper reuse of parts and recycling. This
symbol of the crossed out wheeled bin indicates that the product
(electrical, electronic equipment, and mercury-containing button
cell battery) should not be placed in municipal waste. Check local
technical support services for product recycling.
NO DISASSEMBLY
The warranty does not apply to the products that have been
disassembled by users.
Lithium-Metal Battery Warning
CAUTION: Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type recommended
by the manufacturer. Dispose of used batteries according to the
manufacturer’s instructions.
Federal Communications Commission
Statement
ThisdevicecomplieswithPart15oftheFCCRules.Operationissubjectto
the following two conditions:
• Thisdevicemaynotcauseharmfulinterference,and
• Thisdevicemustacceptanyinterferencereceivedincluding
interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a
ClassBdigitaldevice,pursuanttoPart15oftheFCCRules.Theselimitsare
designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with
manufacturer’s instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorientorrelocatethereceivingantenna.
• Increasetheseparationbetweentheequipmentandreceiver.
• Connecttheequipmenttoanoutletonacircuitdierentfromthatto
which the receiver is connected.
• Consultthedealeroranexperiencedradio/TVtechnicianforhelp.
CAUTION: This transmitter must not be co-located or operated in
conjunction with any other antenna or transmitter. Any changes or
modicationsnotexpresslyapprovedbythegranteeofthisdevicecould
void the user’s authority to operate the equipment.
ASUS Recycling/Takeback Services
ASUS recycling and takeback programs come from our commitment to the
highest standards for protecting our environment. We believe in providing
solutions for you to be able to responsibly recycle our products, batteries,
other components, as well as the packaging materials. Please go to http://
csr.asus.com/english/Takeback.htm for the detailed recycling information
in different regions.
Coating Notice
IMPORTANT! To provide electrical insulation and maintain electrical
safety, a coating is applied to insulate the device except on the areas
where the I/O ports are located.
Declaration of Conformity (R&TTE directive
1999/5/EC)*
* Replaced in 2017 by RED 2014/53/EU
The following items were completed and are considered relevant and
sufficient:
• Essentialrequirementsasin[Article3]
• Protectionrequirementsforhealthandsafetyasin[Article3.1a]
• Testingforelectricsafetyaccordingto[EN60065]
• Protectionrequirementsforelectromagneticcompatibilityin[Article3.1b]
• Testingforelectromagneticcompatibilityaccordingto[EN301489-1]
&[EN301489-17]
• Eectiveuseoftheradiospectrumasin[Article3.2]
• Radiotestsuitesaccordingto[EN300328-2]
Care during use
• Donotwalkonthepowercordorallowanythingtorestonit.
• Donotspillwateroranyotherliquidsonyoursystem.
• Whenthesystemisturnedo,asmallamountofelectricalcurrentstill
flows. Always unplug the power cord from the power outlets before
cleaning the system.
• Ifyouencounterthefollowingtechnicalproblemswiththeproduct,
unplugthepowercordandcontactaqualiedservicetechnicianor
your retailer.
–Thepowercordorplugisdamaged.
–Liquidhasbeenspilledintothesystem.
–Thesystemdoesnotfunctionproperlyevenifyoufollowthe
operating instructions.
–Thesystemwasdroppedorthecasingisdamaged.
–Thesystemperformancechanges.
回収とリサイクルについて
使用済みのコンピューター、ノートパソコン等の電子機器には、環境
に悪影響を与える有害物質が含まれており、通常のゴミとして廃棄す
ることはできません。リサイクルによって、使用済みの製品に使用さ
れている金属部品、プラスチック部品、各コンポーネントは粉砕さ
れ新しい製品に再使用されます。また、その他のコンポーネントや部
品、物質も正しく処分・処理されることで、有害物質の拡散の防止と
なり、環境を保護することに繋がります。
筐体のコーティングについて
重要: 感電などを防ぐため、本機は絶縁性のあるコーティング材を
使用しています(出入力ポート搭載部分を除く)。
「PCリサイクルマーク」の取り扱
いに付いて
この製品には「PCリサイクルマーク」シールが同梱されています。製
品の使用停止後、弊社にPCリサイクルをご依頼いただく際に必要とな
りますので「PCリサイクルマーク」シールをPCの本体に貼り付けてく
ださい。
ご注意:
・ 同梱された「PCリサイクルマーク」シールは本
製品以外には貼り付けないでください。
・ 「PCリサイクルマーク」シールは通風孔を塞が
ない場所を選んで貼り付けてください。
・ 同梱された「PCリサイクルマーク」シールを紛
失された場合、再発行は出来ません。
電気・電子機器に含有される化学物
質の表示について
資源有効利用促進法では、JIS C 0950: 2008 (J-Moss) の定める規格
により、製造元に対し特定の電気・電子機器に含まれる化学物質の
情報提供を義務付けています。J-Moss とは、電気・電子機器に含有
される化学物質の表示に関するJIS規格の略称で、正式名称は「The
marking when content other than exemption does not exceed
reference value of percentage content (電気・電子機器の特定の
化学物質の含有表示方法) 」です。なお、この規格は2008年8月1日よ
り適用されています。
この規格に関する詳細情報はASUSのサイト (http://csr.asus.com)
に記載の「The marking when content other than exemption
does not exceed reference value of percentage content (電気・電
子機器の特定の化学物質の含有表示方法) 」をご参照ください。
Regional notice for California
WARNING! This product may contain chemicals known to the State of
California to cause cancer, birth defects or other reproductive harm. Wash
hands after handling.
DECLARATION OF CONFORMITY
Per FCC Part 2 Section 2. 1077(a)
Responsible Party Name: Asus Computer International
Address: 800 Corporate Way, Fremont
, CA 94539.
Phone/Fax No: (510)739-3777/(510)608-4555
hereby declares that the product
Product Name : VivoStick
Model Number : TS10
Conforms to the following specifications:
FCC Part 15, Subpart B, Unintentional Radiators
Supplementary Information:
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including interference
that may cause undesired operation.
Representative Person’s Name : Steve Chang / President
Signature :
Date : Feb. 22, 2016
Ver. 140331
Canadian Department of Communications
Statement
This digital apparatus does not exceed the Class B limits for radio noise
emissions from digital apparatus set out in the Radio Interference
Regulations of the Canadian Department of Communications.
This class B digital apparatus complies with Canadian ICES-003.
IC Radiation Exposure Statement for
Canada
This equipment complies with IC radiation exposure limits set forth for an
uncontrolled environment. To maintain compliance with IC RF exposure
compliance requirements, please avoid direct contact to the transmitting
antennaduringtransmitting.Endusersmustfollowthespecicoperating
instructions for satisfying RF exposure compliance.
Operation is subject to the following two conditions:
• Thisdevicemaynotcauseinterferenceand
• Thisdevicemustacceptanyinterference,includinginterferencethat
may cause undesired operation of the device.
ICES-3(B)-NMB(3)(B)
User should also be advised that:
(i)thedeviceforoperationintheband5150-5250MHzisonlyforindoor
use to reduce the potential for harmful interference to co-channel mobile
satellite systems;
(ii)themaximumantennagainpermittedfordevicesinthebands5250-5350
MHzand5470-5725MHzshallcomplywiththee.i.r.p.limit;and
(iii)themaximumantennagainpermittedfordevicesintheband5725-5825
MHzshallcomplywiththee.i.r.p.limitsspeciedforpoint-to-pointandnon
point-to-point operation as appropriate. High-power radars are allocated as
primaryusers(i.e.priorityusers)ofthebands5250-5350MHzand5650-5850
MHz and that these radars could cause interference and/or damage to LE-
LAN devices.