Notebook PC User’s Manual DC IN 1394 K Product Name: Notebook PC Hardware Manual Revision: 1.
Safety Statements Federal Communications Commission Statement This device complies with FCC Rules Part 15. Operation is subject to the following two conditions: • This device may not cause harmful interference, and • This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the Federal Communications Commission (FCC) rules.
Safety Statements Nordic Cautions (for Notebook PC with Lithium-Ion Battery) CAUTION! Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions. (English) VORSICHT! Explosionsgetahr bei unsachgemäßen Austausch der Batterie. Ersatz nur durch denselben oder einem vom Hersteller empfohlenem ähnlichen Typ.
Safety Statements Safety Precautions WARNING! The following safety precautions will increase the life of the Notebook PC. Follow all precautions and instructions. Except as described in this manual, refer all servicing to qualified personnel. Do not use damaged power cords, accessories, or other peripherals. Do not use strong solvents such as thinners, benzene, or other chemicals on or near the surface. Disconnect the AC power and remove the battery pack(s) before cleaning.
Safety Statements Transportation Precautions To prepare the Notebook PC for transport, you should turn it OFF and disconnect all external peripherals to prevent damage to the connectors. The hard disk drive’s head retracts when the power is turned OFF to prevent scratching of the hard disk surface during transport. Therefore, you should not transport the Notebook PC while the power is still ON.
Safety Statements CTR 21 Approval (for Notebook PC with built-in Modem) Danish Dutch English Finnish French German Greek Italian Portuguese Spanish Swedish 6
Table of Contents UL Safety Notices Required for UL 1459 covering telecommunications (telephone) equipment intended to be electrically connected to a telecommunication network that has an operating voltage to ground that does not exceed 200V peak, 300V peak-to-peak, and 105V rms, and installed or used in accordance with the National Electrical Code (NFPA 70).
Table of Contents Contents Safety Statements 2 Federal Communications Commission Statement ........................................................ 2 Canadian Department of Communications Statement .................................................. 2 Power Safety Requirement ........................................................................................... 2 Nordic Cautions (for Notebook PC with Lithium-Ion Battery) ........................................
Table of Contents 4. Using the Notebook PC 33 Pointing Device ................................................................................................................ 34 Using the Touchpad .................................................................................................... 34 Touchpad Usage Illustrations ...................................................................................... 34 Caring for the Touchpad ...................................................................
Safety Statements System Memory Expansion ............................................................................................. 54 Processor Upgrades ........................................................................................................ 54 Thermal Power Control ............................................................................................... 55 Hard Disk Drive ............................................................................................................
1.
1 Introducing the Notebook PC About This User’s Manual You are reading the Notebook PC User’s Manual. This User’s Manual provides information on the various components in the Notebook PC and how to use them. The following are major sections of this User’s Manuals: 1. Introducing the Notebook PC Introduces you to the Notebook PC and this User’s Manual. 2. Knowing the Parts Gives you information on the Notebook PC’s components. 3.
2.
2 Knowing the Parts Top Side Refer to the diagram below to identify the components on the top side of the Notebook PC. Display Panel Microphone Instant Launch Keys Power Switch Keyboard Touchpad Touchpad Buttons Optional MP3 Module Status Indicators (described on front side) Opening the Display Panel One spring-loaded latch on the front of the Notebook PC locks the display panel in the closed position when the Notebook PC is not in use.
Knowing the Parts 2 Display Panel The display panel functions the same as a desktop monitor. The Notebook PC uses an active matrix TFT LCD, which provides excellent viewing like that of desktop monitors. Unlike desktop monitors, the LCD panel does not produce any radiation or flickering, so it is easier on the eyes. Display Panel Care The LCD screen is very delicate and requires careful handling.
2 Knowing the Parts Bottom Side Refer to the diagram below to identify the components on the bottom side of the Notebook PC. Name Card Holder Hard Drive Compartment Cooling Fan & Vent Reset Button Battery Compartment MP3 L L Battery Release & Lock L L MP3 Module Release (MP3 Module is Optional) WARNING! The bottom of the Notebook PC (especially between the battery and hard drive compartments, and cooling fan) can get very hot.
Knowing the Parts 2 The following describes the components on the bottom side of the Notebook PC as shown by the illustration on the previous page. Hard Drive Compartment The hard drive compartment has a cover that is secured by the hard drive cover screw. When the cover is removed, the Notebook’s PC hard disk drive can be seen. This design allows easy hard disk drive swapping or upgrading. Cooling Fan & Vent The cooling fan turns ON when the temperature rises past a set threshold.
2 Knowing the Parts Left Side Refer to the diagram below to identify the components on the left side of the Notebook PC. DC IN 1394 USB Head-Out Fast IrDA Port Mic-In DC IN Air Vent & Fan Audio In DC Power IEEE Input Jack 1394 Port DC Power Input Jack The supplied power adapter converts AC power to DC power for use with this jack. Power supplied through this jack supplies power to the Notebook PC and charges the internal battery pack.
Knowing the Parts 2 Audio In Audio input allows feeding in audio from another source in order to listen to it using the Notebook PC’s speakers or to use it for digital multimedia files. Microphone Jack (Mic-In) The mono microphone jack can be used to connect an external microphone or output signals from audio devices. Using this jack automatically disables the built-in microphone.
2 Knowing the Parts Rear Side Refer to the diagram below to identify the components on the rear side of the Notebook PC. K Kensington® Lock Port LAN Modem Port Port (RJ-45) (RJ-11) External Monitor Port Parallel Port AiBox Docking Port PS/2 USB Port Port The following describes the components on the rear side of the Notebook PC as shown by the illustration above.
Knowing the Parts 2 Parallel Port The 25-pin D-sub parallel/printer port supports parallel devices such as a printer or a removable drive. AiBox Docking Port The docking port is for connection to an AiBox portable module bay. More details given later. PS/2 Port The PS/2 port is for connecting an external PS/2 mouse or PS/2 keyboard to the Notebook PC if you do not want to use the built-in pointing device and keyboard. Simultaneous use of two PS/2 devices requires an optional PS/2 Y-adapter.
2 Front Side Refer to the diagram below to identify the components on the front side of the Notebook PC. Display Panel Latch M Left Speaker MP3 Module (optional) Status Indicators Right Speaker Left/Right Speaker The built-in stereo speakers allow you to separately hear left and right channel audio without additional attachments. The multimedia sound system features an integrated digital audio controller that produces rich, vibrant sound in high quality 16-bit stereo.
3.
3 Getting Started Installing and Removing the Battery Pack Your Notebook PC may or may not have its battery pack installed. If your Notebook PC does not have its battery pack installed, there will be a large opening at the bottom of the Notebook PC. Use the following procedures to install or remove the battery pack. To install the battery pack: 1. Insert the battery pack with the connector first 2. Snap the battery pack into the Notebook PC and lock the battery by moving the switch to L .
Getting Started 3 Using the Battery Pack Before you use your Notebook PC on the road, you will have to charge the battery pack. The battery pack begins to charge as soon as the Notebook PC is connected to external power. Fully charge the battery pack before using it for the first time. A new battery pack must completely charge before the Notebook PC is disconnected from external power. The battery pack is fully charged when the battery charge light turns OFF.
3 Getting Started Power Connection Your Notebook PC comes with a universal AC-DC adapter. That means that you may connect the power cord to any 110V-120V as well as 220V-240V outlets without setting switches or using power converters. Different countries may require that an adapter be used to connect the provided US-standard AC power cord to a different standard. Most hotels will provide universal outlets to support different power cords as well as voltages.
Getting Started 3 Powering ON The Notebook PC The Notebook PC’s power-ON message appears on the screen followed by a short beep when you turn it ON. If necessary, you may adjust the brightness by using the hot keys. If you need to run the BIOS Setup to set or modify the system configuration, press [F2] upon bootup to enter the BIOS Setup. If you press the [Esc] button during the splash screen, standard boot information such as the BIOS version can be seen.
3 Getting Started Power Management - Stand By & Hibernate Power management settings can be found in the Windows control panel. The following shows the power options properties in Windows ME. You can define Stand By or Power Off for closing the display panel, pressing the power button, or activating sleep mode. Basically Stand by and Hibernate saves power when your Notebook PC is not in use by turning OFF certain components.
Getting Started 3 Instant Launch Keys and Status Indicators Front Edge of Notebook PC Above the Keyboard Email Key Internet Key 1 Programmable Key 1 Programmable Key 2 2 1 A Email Launch Key Pressing this button will launch your Email application. If your Notebook PC is OFF while pressing this button, this function will first turn ON your Notebook PC. Internet Launch Key Pressing this button will launch your Internet browser application.
3 Getting Started Using the Keyboard Colored Hot Keys The following defines the colored hot keys on the Notebook PC’s keyboard. The colored commands can only be accessed by first pressing and holding the function key while pressing a key with a colored command. F1 SUSPEND Suspend (F1): Places the Notebook PC in suspend mode (either Save-to-RAM or Save-toDisk depending on sleep button setting in power management setup).
Getting Started 3 Microsoft Windows™ Keys There are two special Windows™ keys on the keyboard as described below. The key with the Windows™ Logo activates the Start menu located at the bottom left of the Windows™ desktop. The other key, that looks like a Windows™ menu with a small cursor, activates the properties menu and is equivalent to pressing the right mouse button on a Windows™ object.
3 Getting Started Keyboard as Cursors The keyboard can be used as cursors while Number Lock is ON or OFF in order to increase navigation ease while entering numeric data in spreadsheets or similar applications. With Number Lock OFF, press and one of the cursor keys shown below. For example [Fn][8] for up, [Fn][K] for down, [Fn][U] for left, and [Fn][O] for right. With Number Lock ON, use [Shift] and one of the cursor keys shown below.
4.
4 Using the Notebook PC Pointing Device The Notebook PC’s integrated touchpad pointing device is fully compatible with all two/three-button and scrolling knob PS/2 mice. The touchpad is pressure sensitive and contains no moving parts; therefore, mechanical failures can be avoided. A device driver is still required for working with some application software. See the Driver & Utility Guide for information on drivers and utilities for the touchpad.
Using the Notebook PC 4 Clicking/Tapping - With the cursor over an item, press the left button or use your fingertip to touch the touchpad lightly, keeping your finger on the touchpad until the item is selected. The selected item will change color. The following 2 examples produce the same results.
4 Using the Notebook PC Dragging - Dragging means to pick up an item and place it anywhere on the screen you wish. You can move the cursor over the item you select, and while keeping the left button depressed, moving the cursor to the desired location, then release the button. Or, you can simply double-tap on the item and hold while dragging the item with your fingertip. The following 2 examples produce the same results.
Using the Notebook PC 4 USB Floppy Disk Drive (Optional) The Notebook PC features an optional USB-interface disk drive that accepts a standard 1.44MB (or 720KB) 3.5-inch floppy diskette. The eject button is on the top edge of the floppy disk drive for easy access, unlike desktop PCs with the eject button on the bottom of the floppy disk drive. Floppy access activity can be monitored through the LED on the front of the floppy disk drive. Connection Connection is very easy because of USB technology.
4 Using the Notebook PC AiBox Portable Module Bay (Optional) The external AiBox Portable Module Bay provides a convenient solution to connect external devices such as CD/DVD-ROM, CD-RW, or a second hard disk drive to the Notebook PC using a single cable. External devices can be easily interchanged in the AiBox. WARNING! AiBox now supports Plug & Play on this Notebook PC. When the power is ON, connect the AiBox and/or insert a module drive. The module drive will be automatically detected.
Using the Notebook PC 4 Second Hard Disk Drive Module The convenient design of the Notebook PC allows for the usage of a second hard disk drive in the modular bay. A second hard disk drive allows you to use it as a removable device, for installing dual operating systems, for additional data storage, or to store CDs. To use a second hard disk drive, you must be familiar with the following: • What to purchase and the contents of the kit.
4 Using the Notebook PC CD/CD-RW/DVD Drive Module (optional) The external AiBox Portable Module Bay provides a convenient solution to connect external devices such as CD/DVD-ROM, CD-RW, or a second hard disk drive to the Notebook PC using a single cable. External devices can be easily interchanged in the AiBox.
Using the Notebook PC 4 Inserting a CD 1. While the Notebook PC’s power is ON, press the CD drive eject button and the CD drive tray will eject out partially. 2. Hold the CD drive front panel and slide the CD drive tray completely out. Be careful not to touch the CD drive lens and other mechanisms. Make sure there are no obstructions that may get jammed under the CD drive tray. 3. Hold the CD by the edge and face the printed side up. Snap the CD onto the hub by pressing on both sides of the CD center.
4 Using the Notebook PC DVD-ROM Drive Information Overview The Notebook PC comes with an optional DVD-ROM drive or a CD-ROM drive. In order to view DVD titles, you must install the provided MPEG2 video decoder software and the DVD viewer software included on the DVD module driver support CD. The DVD-ROM drive allows the use of both CD and DVD discs. Definitions DVD, which stands for Digital Versatile Disc, is the next generation of optical disc storage technology.
Using the Notebook PC 4 Regional Playback Information Playback of DVD movie titles involves decoding MPEG2 video, digital AC3 audio and decryption of CSS protected content. CSS (sometimes called copy guard) is the name given to the content protection scheme adopted by the motion picture industry to satisfy a need to protect against unlawful content duplication. Although the design rules imposed on CSS licensors are many, one rule that is most relevant is playback restrictions on regionalized content.
4 Using the Notebook PC Using a CD A CD drive letter should be present regardless of the presence of a CD disc in the drive. After the CD is properly inserted, data can be accessed just like with hard disk drives; except that nothing can be written to or changed on the CD. Vibration is normal for all high-speed CD-ROM drives due to unbalanced CDs or CD print. To decrease vibration, use the Notebook PC on an even surface and do not place labels on the CD.
Using the Notebook PC 4 Optional External Connections Monitor Out Connection Connecting an external monitor is just like on a standard desktop PC. Just plug in the VGA cable and its ready to use (some Notebook PC configurations may require additional display driver settings). You can view the Notebook PC display panel while simultaneously allowing others to view the external monitor. For large audiences, try connecting a computer video projector.
4 Using the Notebook PC PC Card (PCMCIA) Socket The Notebook PC has one PC Card (or sometimes referred to as PCMCIA) sockets located behind a hinged cover to allow expansion just like a desktop computer expansion slot. This allows you to customize your Notebook PC to meet a wide range of application needs. The socket can interface with two type I/II or one type III PC card. PC cards are about the size of a few stacked credit cards and have a 68-pin connector at one end.
Using the Notebook PC 4 Inserting a PC Card (PCMCIA) 2. Carefully connect any cables or adapters needed by the PC card. Usually connectors can only be inserted in one orientation. Look for a sticker, icon, or marking on one side of the connector representing the top side. D N E S IH T T R E S N I 1. Insert the PC card with the connector side first. When the PC card is fully inserted, the PC card bay door can close normally without striking the PC card. Be sure the PC card is level when inserting.
4 Using the Notebook PC Modem and Network Connections The built-in modem and network model comes with both an RJ-11 and an RJ-45 port. RJ-11 telephone cables have two or four wires and are used to connect telephones to telephone outlets found in the walls of residential homes and some commercial buildings (some commercial buildings may have telephone wiring designed for dedicated phone systems that may not be compatible).
Using the Notebook PC 4 Network Connection Connect a network cable, with RJ-45 connectors on each end, to the modem/network port on the Notebook PC and the other end to a hub or switch. For 100BASE-TX speeds, your network cable must be category 5 (not category 3) with twisted-pair wiring. If you plan on running the interface at 100Mbps, it must be connected to a 100BASE-TX hub (not a 100BASE-T4 hub). For 10Base-T, use category 3, 4, or 5 twisted-pair wiring.
4 Using the Notebook PC IR Wireless Communication The Notebook PC is equipped with a conveniently located Infrared (IR) Communication Port (see 2. Knowing the Parts for location). The IR port comes with IrDA (Infrared Data Association) Serial Infrared Data Link Version 1.1 compliance, that allows you to perform point-to-point wireless communications. You can use a SIR/FIR-specified application to transmit or receive data files with other systems equipped with an infrared port.
Using the Notebook PC 4 CAUTION! Disable the infrared communication when you are not using the IR for long periods because the IR consumes a great deal of Windows resources which will decrease the Notebook PC’s performance. AC Power System The Notebook PC power is comprised of two parts, the power adapter and the battery power system. The power adapter converts AC power from a wall outlet to the DC power required by the Notebook PC. The battery pack consists of a set of battery cells housed together.
4 Using the Notebook PC Using Battery Power A fully-charged battery pack provides the system approximately 2 hours of working power. But the actual figure varies depending on how you use the power saving features, your general work habits, the CPU, main memory size, and the size of the display panel. The “Battery Warning” beeps are automatically enabled in Windows 98/ME and continually sounds when down to 10% (configurable in Windows 98/ME) power.
Using the Notebook PC 4 Power Management Modes The Notebook PC has a number of automatic or adjustable power saving features that you can use to maximize battery life and lower Total Cost of Ownership (TCO). You can control some of these features through the Power menu in the BIOS Setup when APM (non-ACPI) is used. ACPI power management settings are made through the operating system.
4 Using the Notebook PC Power Saving In addition to reducing the CPU clock, this mode puts devices including the LCD backlight in their lower active state. The Notebook PC enters Standby mode (low priority) when the system remains idle for a specified amount of time. The timeout can be set through BIOS setup (lower priority) and Windows power management (higher priority). To resume system operation, press any key on the keyboard, touchpad, external mouse, or by moving the mouse.
Using the Notebook PC 4 Thermal Power Control There are three power control methods for controlling the Notebook PC’s thermal state. These power control cannot be configured by the user and should be known in case the Notebook PC should enter these states. The following temperatures represent the chassis temperature (not CPU). • The fan turns ON for active cooling when temperatures are close to the safe upper limit.
4 Using the Notebook PC Hard Disk Drive Hard disk drives have higher capacities and operate at much faster speeds than floppy disk drives and CDROM drives. Enhanced IDE drives provide a reliable, fast, and cost-effective mass storage solution in the PC storage industry. The high speed transfer modes supported are UltraATA/66 up to 66MB/sec and PIO mode 4 up to 16.6MB/sec. The Notebook PC comes with a removable 2.5” (6.35cm) wide and .374” (.
Using the Notebook PC 4 External Keyboard Connection To allow easier data entry, you may connect any PS/2 keyboard as shown here. External Mouse Connection A USB mouse can be easily connected to the Notebook PC. There is only one correct orientation with the USB symbol facing upwards. The USB mouse will work simultaneously with the Notebook PC’s touchpad. For more than one USB connection, you can purchase either a separate hub or a keyboard with integrated USB hub.
4 Using the Notebook PC Vehicle/Air & Vehicle-Only Power Adapters (Optional) The main purpose of the vehicle/air or vehicle-only power adapters is to provide a source of power for using the Notebook PC and/or charging the Notebook PC’s battery from while in transit when no AC power is available. These products are essential tools for today’s mobile professional.
Using the Notebook PC 4 Securing Your Notebook PC For system and hard disk drive security, see BIOS setup “Security”. A third party lock such as the ones by Kensington® can be used to secure your Notebook PC physically to an unmovable object. The cable wraps around an object and the “T” shaped end inserts into the Kensington® lock port as shown in this illustration and a key or combination dial is used to secure the lock in place.
4 Using the Notebook PC MP3 Player Module (Optional) A detailed manual is provided with the MP3 player module. The page is only a quick overview. The pocket-sized self-powered MP3 module is a versatile digital audio recorder and player. The MP3 module allows you to store MP3 audio downloaded from the Internet and play them through headphones.
5.
5 5. Configuring the BIOS BIOS Setup Program This Notebook PC supports a programmable EEPROM that stores the BIOS software and can be updated using the provided flash memory writer utility. This Section will guide you through the BIOS setup program by providing clear explanations for all the options. A default configuration has already been set. If you are either installing new devices or expanding main memory, you will need to enter the BIOS Setup to reconfigure your Notebook PC.
5. Configuring the BIOS 5 Updating your BIOS This Notebook PC supports an easy-to-use BIOS update software called “WINFLASH” which is installed through the provided support CD. If you need help installing or using “WINFLASH”, refer to the “Driver & Utility Manual”. BIOS Menu Bar The top of the screen has a menu bar with the following selections: MAIN ADVANCED SECURITY Use this menu to make changes to the basic system configuration.
5 5. Configuring the BIOS General Help In addition to the Item Specific Help window, the BIOS setup program also provides a General Help screen. This screen can be called up from any menu by simply pressing [F1] or the [Alt] + [H] combination. The General Help screen lists the legend keys with their corresponding alternates and functions. Scroll Bar When a scroll bar appears to the right of a help window, it indicates that there is more information to be displayed that will not fit in the window.
5 5. Configuring the BIOS General Help In addition to the Item Specific Help window, the BIOS setup program also provides a General Help screen. This screen can be called up from any menu by simply pressing [F1] or the [Alt] + [H] combination. The General Help screen lists the legend keys with their corresponding alternates and functions. Scroll Bar When a scroll bar appears to the right of a help window, it indicates that there is more information to be displayed that will not fit in the window.
5 5. Configuring the BIOS Main Menu When the Setup program is accessed, the main menu screen appears as shown: Item Specific Help System Time System Date [17:15:00] [06/13/2001] Primary Master Secondary Master Video Display Device Installed Memory [IBM-DJSA-220] [Auto] [LCD & CRT] 128 MB to select field; <+>,<-> to change value. NOTE: In the following BIOS item descriptions, the item headings in square brackets represent the default settings for those fields.
5. Configuring the BIOS 5 >Primary Master (described later) >Secondary Master (described later) >Secondary Slave (described later) Video Display Device [LCD & CRT] This field allows you to select and enable video display devices, such as an LCD panel, an external CRT/LCD monitor, or both. The configuration options are: [LCD & CRT] [LCD] [CRT] Installed Memory [128 MB] (display field) This field displays the amount of extended memory as detected by the system.
5 5. Configuring the BIOS Primary Master (sub-menu) This field is used to configure the primary IDE drive installed in the system. To configure a hard disk drive, select this sub-menu from the Main menu and press the Enter key to enter this sub-menu.
5. Configuring the BIOS Cylinders [ 5 ] This field configures the number of cylinders. Refer to your drive documentation to determine the correct value to enter into this field. NOTE: To make changes to this field, the Type field must be set to User. Heads [ ] This field configures the number of read/write heads. Refer to your drive documentation to determine the correct value to enter into this field. NOTE: To make changes to this field, the Type field must be set to User.
5 5. Configuring the BIOS Secondary Master / Secondary Slave (sub-menus) This field is used to configure the secondary IDE drive installed in the system. To configure a hard disk drive, select this sub-menu from the Main menu and press the Enter key to enter this sub-menu. The fields and options on this sub-menu are the same as the previous menu described earlier. Leave on the default setting of Auto. Secondary Master: NOTE: The Secondary drive displayed here is for example only.
5. Configuring the BIOS 5 Advanced Menu Selecting Advanced from the main menu bar display the Advanced menu as shown below. Item Specific Help I/O Device Configuration Processor Serial Number Internal Pointing Device Quick Power On Self Test [Disabled] [Enabled] [Enabled] to go to the sub-menu. >I/O Device Configuration (described on next page) Pressing [Enter] when this field is highlighted calls up a sub-menu for configuring the Notebook PC’s serial and parallel ports.
5 5. Configuring the BIOS I/O Device Configuration (sub-menu) I/O Device Configuration IR Port Mode DMA Channel [2F8H/IRQ3] [FIR] [1] Parallel Port Mode ECP DMA Select [378H/IRQ7] [ECP+EPP] [3] Item Specific Help to select the I/O Address & IRQ for IR. NOTE: The presence of sub-items in this menu is dependent on certain relevant settings.
5. Configuring the BIOS 5 Parallel Port: [378H/IRQ7] This field allows you to configure the Notebook PC parallel port. The configuration options are: [Disabled] [378H/IRQ7] [278H/IRQ5] Mode: [ECP+EPP] The Mode field allows you to configure the Notebook PC parallel port transmission mode. The configuration options are: [Normal] [EPP] [ECP] [ECP+EPP] EPP Mode: When the EPP mode is selected, the standard and bidirectional modes are also available. The EPP operates on a two phase cycle.
5 5. Configuring the BIOS Security Menu The Notebook PC’s advanced system of security allows you to set a password to prevent unauthorized access to system resources, data, and the BIOS Setup Program. This Section covers each parameter of the Security Setup. Selecting Security from the menu bar displays the following menu: Item Specific Help System Password Password on boot Hard disk Password [Enter] [Disabled] [Enter] Supervisor password controls full access.
5. Configuring the BIOS 5 System Password [Enter] This field allows you to set the password. To set the password, highlight this field and press [Enter]. Type a password and press [Enter]. You can type up to eight alphanumeric characters. Symbols and other keys are ignored. Type the same password a second time to confirm and press [Enter]. The password is now set. To change the password, repeat the same process and enter a different password.
5 5. Configuring the BIOS Power Menu The Power menu of the Setup program allows you to manually enable and adjust certain power saving features of the Notebook PC, which are necessary for systems without APM or ACPI. For Windows 98 with APM or ACPI, all power saving controls (except “Suspend Mode”) are made through the operating system. Enabling these features will extend the life of the battery pack between charges. To make changes to power management settings, select Power Savings from the menu bar.
5. Configuring the BIOS 5 Video Timeout [Disabled] This field allows you to specify the period of inactivity required before the display panel turns off. The configuration options are: [Disabled] [1-2 Min] [2-3 Min] [4-5 Min] [6-7 Min] [8-9 Min] [10-11 Min] [15-16 Min] Hard Disk Timeout [Disabled] This field allows you to specify the period of inactivity required before the hard disk spins down and enters power saving mode. The configuration options are: [Disabled] [1 Min] [2 Min]...
5 5. Configuring the BIOS Boot Menu The Boot menu allows the user to specify the order in which the Notebook PC is to check for a device to boot the system. To make changes, select Boot from the menu bar and the following screen appears: Item Specific Help 1. Removable Device 2. IDE Hard Drive 3. ATAPI CD-ROM 4. Other Boot Device [USB FDD] [IBM-DJSA-220] [None] [INT18 Device (Network)] Boot Sequence: to select the device. To select the boot sequence, use the up or down arrow.
5. Configuring the BIOS 5 Exit Menu Once you have made all of your selections from the various menus in the Setup program, you should save your changes and exit Setup. Select Exit from the menu bar to display the following menu: Item Specific Help Exit Saving Changes Exit Discarding Changes Load Setup Defaults Discard Changes Save Changes Exit setup utility and save your changes to CMOS. NOTE: Pressing the [Esc] key does not exit this menu.
5 5. Configuring the BIOS Load Setup Defaults This option allows you to load the default values for each of the parameters on the Setup menus. When this option is selected or if [F9] is pressed, a confirmation is requested. Select Yes to load default values programmed into the BIOS file (the default values may change from one BIOS version to another). You can now select Exit Saving Changes or make other changes before saving the values to the EEPROM.
APPENDIX Internal Modem Compliancy Glossary Owner Information 80
A APPENDIX Internal Modem Compliancy Protocols and Compliancy The Notebook PC with internal modem model complies with JATE (Japan), FCC (US, Canada, Korea, Taiwan), and CTR21. The internal modem has been approved in accordance with Council Decision 98/ 482/EC for pan-European single terminal connection to the public switched telephone network (PSTN).
APPENDIX A This table shows the countries currently under the CTR21 standard.
A 84 APPENDIX
A APPENDIX Glossary ACPI (Advanced Configuration and Power Management Interface) Modern standard for reducing power usage in computers. APM (Advanced Power Management) Modern standard for reducing power usage in computers. AWG (American Wire Gauge) Gauge AWG Diam (mm) Area (mm2) R (ohm/km) I@3A/mm2 (mA) Gauge AWG Diam (mm) Area (mm2) R (ohm/km) I@3A/mm2 (mA) 46 0.04 0.0013 13700 3.8 24 0.50 0.20 87.5 588 44 0.05 0.0020 8750 6 0.55 0.24 72.3 715 42 41 0.06 0.07 0.0028 0.
A APPENDIX BIOS (Basic Input/Output System) BIOS is a set of routines that affect how the computer transfers data between computer components, such as memory, disks, and the display adapter. The BIOS instructions are built into the computer’s read-only memory. BIOS parameters can be configured by the user through the BIOS Setup program. The BIOS can be updated using the provided utility to copy a new BIOS file into the EEPROM. Bit (Binary Digit) Represents the smallest unit of data used by the computer.
APPENDIX A IDE (Integrated Drive Electronics) IDE devices integrate the drive control circuitry directly on the drive itself, eliminating the need for a separate adapter card (in the case for SCSI devices). UltraDMA/33 IDE devices can achieve up to 33MB/Sec transfer. IEEE1394 Also known as iLINK (Sony) or FireWire (Apple). IEEE1394 is a high speed serial bus like SCSI but has simple connections and hot-plugging capabilities like USB.
A APPENDIX POST (Power On Self Test) When you turn on the computer, it will first run through the POST, a series of software-controlled diagnostic tests. The POST checks system memory, the motherboard circuitry, the display, the keyboard, the diskette drive, and other I/O devices. PS/2 Port PS/2 ports are based on IBM Micro Channel Architecture. This type of architecture transfers data through a 16-bit or 32-bit bus. A PS/2 mouse and/or keyboard may be used on ATX motherboards.
APPENDIX A Index A C AC Power System 50 AiBox Portable Module 38 APM and ACPI 53 Canadian Department of Communications 2 Capital Lock 29 CardBus 46 CDRH Regulations 3 Colored Hot Keys 30 Cooling Fan 18 CTR 21 Approval 6 B Battery Pack 24 Battery Power System 50 BIOS Advanced Menu 71 BIOS Legend Bar 63 BIOS Menu Bar 63 BIOS Setup Program 62 Boot Menu 78 Boot Sequence 78 Cylinders 69 Discard Changes 80 DMA Channel 72, 73 Exit Discarding Changes 79 Exit Menu 79 Exit Saving Changes 79 Heads 69 I/O Device
A APPENDIX M T Macrovision Notice 3 Microphone Jack 19 Microsoft Windows™ Keys 31 Modem and Network Connections 48 Modem Port 20 Monitor Out Connection 45 Mouse or Keyboard Connection 57 Table of Contents 7, 8, 9 Thermal Power Control 55 Touchpad and Buttons 15 Touchpad, Caring 36 Touchpad, Using 34 Transportation Precautions 5 Twisted-Pair Cable 49, 88 N U Network Connection 49 Nordic Cautions 3 Number Lock 29 Numeric Keypad, alternate 31 UL Safety Notices 7 USB Floppy Disk Drive 37 User’s Manual,
APPENDIX A 91
A APPENDIX Owner Information This page is provided for recording information concerning your Notebook PC for future reference or for technical support. Keep this User’s Manual in a secured location if passwords are filled out.
