R SP98AGP-X Pentium ATX Motherboard ® USER’S MANUAL
USER’S NOTICE No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. (“ASUS”).
ASUS CONTACT INFORMATION ASUSTeK COMPUTER INC. Marketing Address: Telephone: Fax: Email: 150 Li-Te Road, Peitou, Taipei, Taiwan 112 +886-2-2894-3447 +886-2-2894-3449 info@asus.com.tw Technical Support Fax: BBS: Email: WWW: FTP: +886-2-2895-9254 +886-2-2896-4667 tsd@asus.com.tw www.asus.com.tw ftp.asus.com.tw/pub/ASUS ASUS COMPUTER INTERNATIONAL Marketing Address: Fax: Email: 6737 Mowry Ave, Mowry Business Center, Building 2, Newark, CA 94560, USA +1-510-608-4555 info-usa@asus.com.
CONTENTS I. INTRODUCTION ........................................................................... 7 How this Manual is Organized ........................................................ 7 Item Checklist .................................................................................. 7 II. FEATURES .................................................................................... 8 Features of the ASUS SP98AGP-X Motherboard ........................... 8 ASUS Smart Series of Motherboards ..............
CONTENTS PNP and PCI Setup .................................................................. 49 Details of PNP and PCI Setup ............................................ 49 Load BIOS Defaults ................................................................. 51 Load Setup Defaults ................................................................. 51 Supervisor Password and User Password ................................ 52 IDE HDD Auto Detection ........................................................
FCC & DOC COMPLIANCE Federal Communications Commission Statement This device complies with FCC Rules Part 15. Operation is subject to the following two conditions: • • This device may not cause harmful interference, and This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
I. INTRODUCTION I. INTRODUCTION Manual / Checklist How this Manual is Organized This manual is divided into the following sections: I. II. III. IV. V. VI. VII. Introduction Features Installation BIOS Software Support Software ASUS SCSI Cards ASUS PCI-L101 Manual information and checklist Information and specifications concerning this product Instructions on setting up the motherboard.
II. FEATURES Features of the ASUS SP98AGP-X Motherboard II. FEATURES ASUS SP98AGP-X The ASUS SP98AGP-X is carefully designed for the demanding PC user who wants many features in a small package. This motherboard: • AGP Chipset: SiS5591 chipset with built-in AGP support for high performance, component level interconnection targeted at 3D graphical display applications. • Versatile Processor Support: Intel Pentium® 75-233MHz (P55C-MMX™, P54C/ P54CS), IBM®/Cyrix® 6x86-PR166+ (Rev 2.
II. FEATURES ASUS Smart Series of Motherboards II. FEATURES Smart Series Performance • SDRAM Optimized Performance — ASUS Smart series of motherboards support the new generation memory, Synchronous Dynamic Random Access Memory (SDRAM). • Double the IDE Transfer Speed — ASUS Smart series of motherboards with SiS5591 chipset improves IDE transfer rate using Bus Master UltraDMA/33 IDE which can handle data transfer up to 33MB/s.
II. FEATURES • • II. FEATURES Smart Series • • • • 10 Voltage Monitoring and Alert — System voltage levels are monitored to ensure stable current to critical motherboard components. Voltage specifications are more critical for future processors, so monitoring is necessary to ensure proper system configuration and management.
II. FEATURES The ASUS SP98AGP-X Motherboard ATX Power Connector 512KB/1024KB Pipelined CPU Thermal CPU ZIF Socket 7 Sensor Burst L2 Cache T: PS/2 Mouse B: PS/2 Keyboard II. FEATURES Motherboard Parts T: USB Port 1 B: USB Port 2 COM 1 T: Parallel Conn. B: Serial Conn.
III. INSTALLATION BUS Freq. Top: Mouse Bottom: Keyboard BF2 BF1 BF0 Board Power Input for ATX Power Supply PWR_FAN CPU_FAN KBV_SEL Top: USB 1 Bottom: USB 2 LM75 Secondary IDE DIMM Socket 1 (64-bit, 168-pin module) COM 2 Line Out CPU Thermal Sensor (Hardware Monitor) 512KB/1024KB Onboard L2 Cache Line In Multi-I/O Chip Mic In Game/Midi Port III.
III. INSTALLATION Jumpers 1) 2) 3) 4) 5) RTCLR KBV_SEL FS0, FS1, FS2 BF0, BF1, BF2 VID0, 1, 2, 3 p. 15 p. 18 p. 16 p. 16 p. 18 Real Time Clock RAM (Operation/Clear Data) Keyboard Voltage Selection CPU External Clock (BUS) Frequency Selection CPU:BUS Frequency Ratio CPU Voltage Regulator Output Selection p. 19 p. 22 p. 23 p. 23 System Memory Upgrade Central Processing Unit (CPU) Socket 16-bit ISA Bus Expansion Slots* 32-bit PCI Bus Expansion Slots p. 25 p. 25 p. 26 p. 26 p. 26 p. 27 p. 27 p. 27 p.
III. INSTALLATION Installation Steps Before using your computer, you must complete the following steps: 1. 2. 3. 4. 5. 6. Set Jumpers on the Motherboard Install System Memory Install the Central Processing Unit (CPU) Install Expansion Cards Connect Ribbon Cables, Cabinet Wires, and Power Supply Setup the BIOS Software 1. Jumpers III. INSTALLATION Jumpers Several hardware settings are made through the use of jumper caps to connect jumper pins (JP) on the motherboard.
III. INSTALLATION Jumper Settings 1. Real Time Clock (RTC) RAM (RTCLR) The CMOS RAM is powered by the onboard button cell battery. To clear the RTC data: (1) Turn off your computer and remove the AC power , (2) Move this jumper to “Clear CMOS,” (3) Move the jumper back to “Normal,” (4) Turn on your computer, (5) Hold down during bootup and enter BIOS setup to re-enter user preferences.
III. INSTALLATION 2. Keyboard Power Selection (KBV_SEL) This jumper allows you to select the power current for your keyboard. Make sure that your power supply can support at least 300mAmp +5VSB before selecting +5VSB. Multi-I/O +5V +5VSB KBV_SEL [1-2] (Default) [2-3] KBV_SEL 1 2 3 KBV_SEL 1 2 3 +5VSB +5V (Default) R III. INSTALLATION Jumpers Keyboard Voltage Selection 3. CPU External (BUS) Frequency Selection (FS0, FS1, FS2) These jumpers tell the clock generator what frequency to send to the CPU.
III. INSTALLATION (BUS Freq.) (Freq. Ratio) CPU Model Intel Pentium P54C Freq. 166MHz Ratio BUS Freq. A-2.5x 66MHz FS2 FS1 FS0 [2-3] [2-3] [1-2] BF0 BF1 BF2 [2-3] [2-3] [1-2] Intel Pentium P54C Intel Pentium P54C Intel Pentium P54C 150MHz 133MHz 120MHz A-2.5x A-2.0x A-2.0x 60MHz 66MHz 60MHz [2-3] [2-3] [2-3] [2-3] [2-3] [1-2] [2-3] [2-3] [2-3] [2-3] [2-3] [1-2] [2-3] [1-2] [1-2] [2-3] [1-2] [1-2] Intel Pentium P54C Intel Pentium P54C 100MHz 90MHz A-1.5x A-1.
III. INSTALLATION 5. Voltage Regulator Output Selection (VID0, 1, 2, 3) These jumpers set the voltage supplied to the CPU. Pentium MMX (P55C) Intel Pentium (P54C) AMD-K6 (150MHz-233MHz) (75MHz-200MHz) (PR166 and faster) AMD-K5 (PR75-PR133) IBM/Cyrix 6x86(MX) IBM/Cyrix 6x86(M1) (PR166 and faster) (PR166 and faster) WARNING! Because CPU designs change rapidly, the following chart is only intended as a simple quideline and is not intended to be true for your CPU.
III. INSTALLATION 2. System Memory (DIMM) Only Dual Inline Memory Modules (DIMMs) can be used with this motherboard. Three sockets are available for 3.3Volt (power level) Unbuffered Synchronous DRAMs (SDRAMs; 8, 16, 32, 64, or 128MB) or EDO DRAM (8, 16, 32, 64, 128, or 256MB) to form a memory size between 8MB to 768MB. One side (with memory chips) of the DIMM module takes up one Row on the motherboard.
III. INSTALLATION DIMM Memory Installation Procedures: Insert the module(s) as shown. Because the number of pins are different on either side of the breaks, the module will only fit in the orientation as shown. DRAM SIMM modules have the same pin contact on both sides. SDRAM DIMM modules have different pin contact on each side and therefore have a higher pin density. 20 Pins 60 Pins 88 Pins R III.
III.
III. INSTALLATION 3. Central Processing Unit (CPU) The motherboard provides a 321-pin ZIF Socket 7 that is backwards compatible with ZIF Socket 5 processors. The CPU that came with the motherboard should have a fan attached to it to prevent overheating. If this is not the case then purchase a fan before you turn on your system. Apply thermal jelly to the CPU top and then install the fan onto the CPU.
III. INSTALLATION 4. Expansion Cards WARNING! Make sure that you unplug your power supply when adding or removing expansion cards or other system components. Failure to do so may cause severe damage to both your motherboard and expansion cards. Expansion Card Installation Procedure: III. INSTALLATION Expansion Cards 1. Read your expansion card documentation on any hardware and software settings that may be required to setup your specific card. 2. Set any necessary jumpers on your expansion card. 3.
III. INSTALLATION To simplify this process this motherboard has complied with the Plug and Play (PNP) specification which was developed to allow automatic system configuration whenever a PNP-compliant card is added to the system. For PNP cards, IRQs are assigned automatically from those available. If the system has both Legacy and PNP ISA cards installed, IRQs are assigned to PNP cards from those not used by Legacy cards.
III. INSTALLATION 5. External Connectors WARNING! Some pins are used for connectors or power sources. These are clearly distinguished from jumpers in the Motherboard Layout. Placing jumper caps over these connector pins will cause damage to your motherboard. IMPORTANT: Ribbon cables should always be connected with the red stripe on the Pin 1 side of the connector. The four corners of the connectors are labeled on the motherboard.
III. INSTALLATION 3. Parallel Port Connector (25-pin Female) You can enable the parallel port and choose the IRQ through “Onboard Parallel Port” in Chipset Features Setup of the BIOS SOFTWARE. NOTE: Serial printers must be connected to the serial port. Parallel (Printer) Port (25-pin Female) III. INSTALLATION Connectors 4. Serial Port COM1 and COM2 Connectors (Two 9-pin Male) The two serial ports can be used for pointing devices or other serial devices.
III. INSTALLATION 6. Audio Port Connectors (Three 1/8” Female) (with optional onboard audio) Line Out can be connected to headphones or preferably powered speakers. Line In allows tape players or other audio sources to be recorded by your computer or played through the Line Out. Mic allows microphones to be connected for inputing voice. Line Out Line In Mic 1/8" Stereo Audio Connectors III. INSTALLATION Connectors 7.
III. INSTALLATION 9. Primary / Secondary IDE connectors (Two 40-1pin IDE) These connectors support the provided IDE hard disk ribbon cable. After connecting the single end to the board, connect the two plugs at the other end to your hard disk(s). If you install two hard disks, you must configure the second drive to Slave mode by setting its jumper accordingly. Please refer to the documentation of your hard disk for the jumper settings.
III. INSTALLATION 11. Chassis, CPU , & Power Supply Fan Connectors (3-pin CHA_, CPU_, PWR_FAN) These connectors support cooling fans of 500mAMP (6 Watts) or less. Orientate the fans so that the heat sink fins allow airflow to go across the onboard heat sink(s) instead of the expansion slots. Depending on the fan manufacturer, the wiring and plug may be different. The red wire should be positive, while the black should be ground.
III. INSTALLATION 13. IrDA / Fast IR-Compliant infrared module connector (5-pin IR) This connector supports the optional wireless transmitting and receiving infrared module. This module mounts to a small opening on system cases that support this feature. You must also configure the setting through “UART2 Use Infrared” in Chipset Features Setup to select whether UART2 is directed for use with COM2 or IrDA.
III. INSTALLATION 15. Wake on LAN (3-pin WOL) The WAKE_LAN connector allows the system to power up when there is a wakeup package (signal) received from the network through the ASUS PCIL101 LAN card. Requires the ASUS PCI-L101 and an ATX power supply with at least 720mAmp +5VSB. PME Ground +5 Volt Standby R Wake On LAN Connector III. INSTALLATION Connectors 16.
III. INSTALLATION 18. Message LED Lead (MSG.LED, 2 pins) This indicates whether a message has been received from a fax/modem. The LED will remain lit when there is no signal and blink when data are being transfer or messages are waiting in the inbox. This function requires ACPI OS support. III. INSTALLATION Connectors 19.
III. INSTALLATION Power Connection Procedures 1. After all jumpers and connections are made, close the system case cover. 2. Be sure that all switches are off (in some systems, marked with ). 3. Connect the power supply cord into the power supply located on the back of your system case according to your system user’s manual. 4. Connect the power cord into a power outlet that is equipped with a surge protector. III. INSTALLATION Power Connections 5.
IV. BIOS SOFTWARE Support Software FILELIST.TXT - View this file to see the files included in the support software. PFLASH.EXE - This is the Flash Memory Writer utility that updates the BIOS by uploading a new BIOS file to the programmable flash ROM chip on the motherboard. To determine the BIOS version, check the last four numbers of the code displayed on the upper left-hand corner of your screen during bootup. Larger numbers represent a newer BIOS file.
IV. BIOS SOFTWARE 3. Advanced Features This option displays the Advanced Features screen for clearing the PnP configuration record and updating the motherboard BIOS. IV. BIOS Flash Memory Writer Advanced Features Menu 1. Clear PNP ESCD Parameter Block This option erases the Plug-and-Play (PnP) configuration record. 2.
IV. BIOS SOFTWARE Managing and Updating Your Motherboard’s BIOS Upon First Use of the Computer System 1. Create a bootable system floppy diskette by typing [FORMAT A:/S] from the DOS prompt without creating “AUTOEXEC.BAT” and “CONFIG.SYS” files. 2. Copy PFLASH.EXE to your new diskette. 3. Run PFLASH.EXE from your new diskette and select option 1 “Save Current BIOS to File.” Enter the “Current BIOS Revision:” for the file name.
IV. BIOS SOFTWARE 6. BIOS Setup The motherboard supports two programmable Flash ROM chips: 5 Volt and 12 Volt. Either of these memory chips can be updated when BIOS upgrades are released. Use the Flash Memory Writer utility to download the new BIOS file into the ROM chip as described in detail in this section. All computer motherboards provide a Setup utility program for specifying the system configuration and settings.
IV. BIOS SOFTWARE Load Defaults The Load BIOS Defaults option loads the minimum settings for troubleshooting. Load Setup Defaults, on the other hand, is for loading optimized defaults for regular use. Choosing defaults at this level will modify all applicable settings. A section at the bottom of the preceding screen displays the control keys for this screen. Take note of these keys and their respective uses.
IV. BIOS SOFTWARE Time To set the time, highlight the “Time” field and then press either / or <+>/<–> to set the current time. Follow the hour, minute and second format. Valid values for hour, minute and second are: (Hour: (00 to 23), Minute: (00 to 59), Second: (00 to 59). If you do not want to modify the current time, press three times to go to Hard Disks. NOTE: You can bypass the date and time prompts by creating an AUTOEXEC.BAT file.
IV. BIOS SOFTWARE Auto detection of hard disks on bootup For each field: Primary Master, Primary Slave, Secondary Master, and Secondary Slave, you can select Auto under the TYPE and MODE fields. This will enable auto detection of your IDE hard disk during bootup. This will allow you to change your hard disks (with the power off) and then power on without having to reconfigure your hard disk type.
IV. BIOS SOFTWARE BIOS Features Setup BIOS Features Setup consists of configuration entries that allow you to improve your system performance, or let you set up some system features according to your preference. Some entries are required by the motherboard’s design to remain in their default settings. IV. BIOS BIOS Features A section at the lower right of the screen displays the control keys you can use. Take note of these keys and their respective uses.
IV. BIOS SOFTWARE HDD Sequence SCSI/IDE First (IDE) When using both SCSI and IDE hard disk drives, IDE is always the boot disk using drive letter C (default setting of IDE). This new feature allows a SCSI hard disk drive to be the boot disk when set to SCSI. This allows multiple operating systems to be used on both IDE and SCSI drives or the primary operating system to boot using a SCSI hard disk drive. Boot Sequence (C,A) This field determines where the system looks first for an operating system.
IV. BIOS SOFTWARE Video ROM BIOS Shadow (Enabled) This field allows you to change the video BIOS location from ROM to RAM. Relocating to RAM enhances system performance, as information access is faster than the ROM. C8000 - CBFFF Shadow to DC000 - DFFFF Shadow (Disabled) These fields are used for shadowing other expansion card ROMs. If you install other expansion cards with ROMs on them, you will need to know which addresses the ROMs use to shadow them specifically.
IV. BIOS SOFTWARE Chipset Features Setup This “Chipset Features Setup” option controls the configuration of the board’s chipset. Control keys for this screen are the same as in the BIOS Features Setup screen. NOTE: SETUP Defaults are noted in parenthesis next to each function heading. Details of Chipset Features Setup IV. BIOS Chipset Features EDO/FPM Configuration (60ns DRAM) The default setting of 60ns DRAM automatically sets the optimal timings for items 2–7 for 60ns DRAM modules.
IV. BIOS SOFTWARE Graphics Aperture Size (64MB) (Leave on default setting of 64MB) Memory-mapped, graphics data structures can reside in a Graphics Aperture. Memory Hole at Address (None) This features reserves either 12MB-16MB, 14MB-16MB, or 15MB-16MB memory address space to ISA expansion cards that specifically require this setting. Memory from either 12MB and up, 14MB and up, or 15MB and up will be unavailable to the system because expansion cards can only access memory up to 16MB.
IV. BIOS SOFTWARE Onboard Parallel Port (378H/IRQ7) This field sets the address of the onboard parallel port connector. You can select either 3BCH / IRQ 7, 378H / IRQ 7, 278H / IRQ 5, or Disabled. If you install an I/O card with a parallel port, ensure that there is no conflict in the address assignments. The PC can support up to three parallel ports as long as there are no conflicts for each port. Parallel Port Mode (ECP+EPP) This field allows you to set the operation mode of the parallel port.
IV. BIOS SOFTWARE Power Management Setup IV. BIOS Chipset Features This “Power Management Setup” option allows you to reduce power consumption. This feature turns off the video display and shuts down the hard disk after a period of inactivity. NOTE: SETUP Defaults are noted in parenthesis next to each function heading. Details of Power Management Setup IV. BIOS Power Management Power Management (User Define) This field acts as the master control for the power management modes.
IV. BIOS SOFTWARE Video Off Method (DPMS OFF) This field defines the video off features. These options are available: DPMS OFF, DPMS Reduce ON, Blank Screen, V/H SYNC+Blank, DPMS Standby, and DPMS Suspend. The DPMS (Display Power Management System) features allow the BIOS to control the video display card if it supports the DPMS feature. Blank Screen only blanks the screen (or monitors without power management or “green” features).
IV. BIOS SOFTWARE Thermal Monitor (xxxC/xxxF) The onboard hardware monitor can detect the CPU and MB (motherboard) temperatures. These values refresh upon key entries. Set to Ignore only if necessary. Voltage Monitor (xx.xV) The onboard hardware monitor can detect the voltages put out by the voltage regulators. These values refresh upon key entries. Set to Ignore only if necessary. NOTE: If any of the monitored items are out of range, you will get an error message.
IV. BIOS SOFTWARE IRQ xx Used By ISA (No/ICU) These fields indicate whether or not the displayed IRQ for each field is being used by a legacy (non-PnP) ISA card. Two options are available: No/ICU and Yes. The first option, the default value, indicates either that the displayed IRQ is not used or an ISA Configuration Utility (ICU) is being used to determine if an ISA card is using that IRQ.
IV. BIOS SOFTWARE Load BIOS Defaults This “Load BIOS Defaults” option allows you to load the troubleshooting default values permanently stored in the BIOS ROM. These default settings are non-optimal and disable all high performance features. To load these default settings, highlight “Load BIOS Defaults” on the main screen and then press . The system displays a confirmation message on the screen. Press and then to confirm. Press and then to abort.
IV. BIOS SOFTWARE Supervisor Password and User Password These two options set the system passwords. “Supervisor Password” sets a password that will be used to protect the system and the Setup utility; “User Password” sets a password that will be used exclusively on the system. By default, the system comes without any passwords. To specify a password, highlight the type you want and then press . A password prompt appears on the screen.
IV. BIOS SOFTWARE IDE HDD Auto Detection This “IDE HDD Auto Detection” option detects the parameters of an IDE hard disk drive, and automatically enters them into the Standard CMOS Setup screen. IV. BIOS HDD Autodetection Up to four IDE drives can be detected, with parameters for each listed inside the box. To accept the optimal entries, press or else select from the numbers displayed under the OPTIONS field (2, 1, 3 in this case); to skip to the next drive, press .
IV. BIOS SOFTWARE IMPORTANT: If your hard disk was already formatted on an older previous system, incorrect parameters may be detected. You will need to enter the correct parameters manually or use low-level format if you do not need the data stored on the hard disk. If the parameters listed differ from the ones used when the disk was formatted, the disk will not be readable. If the auto-detected parameters do not match the ones that should be used for your disk, do not accept them.
V. SUPPORT SOFTWARE ASUS Smart Motherboard Support CD Install ASUS PC Probe: Installs the ASUS PC Probe utility to monitor fan, temperature, and voltage statuses in your computer. • Install AGP VxD Driver: Installs the SiS 5591 AGP VxD driver. • Install Sound Card & Joystick Driver: Installs the Crystal audio drivers. • Install IDE Driver: Installs the SiS 5591 IDE driver. • Browse this CD: Allows you to see the contents of the ASUS support CD.
V. SUPPORT SOFTWARE Desktop Management Interface (DMI) Introducing the ASUS DMI Configuration Utility This motherboard supports DMI within the BIOS level and provides a DMI Configuration Utility to maintain the Management Information Format Database (MIFD). DMI is able to auto-detect and record information pertinent to a computer’s system such as the CPU type, CPU speed, and internal/external frequencies, and memory size.
V. SUPPORT SOFTWARE Using the ASUS DMI Configuration Utility Edit DMI (or delete) Use the ←→ (left-right) cursors to move the top menu items and the ↑↓ (up-down) cursor to move between the left hand menu items. The bottom of the screen will show the available keys for each screen. Press enter at the menu item to enter the right hand screen for editing. “Edit component” appears on top. The reversed color field is the current cursor position and the blue text are available for editing.
V. SUPPORT SOFTWARE Save MIFD You can save the MIFD (normally only saved to flash ROM) to a file by entering the drive and path here. If you want to cancel save, you may press ESC and a message “Bad File Name” appears here to show it was not saved. Load MIFD You can load the disk file to memory by entering a drive and path and file name here. Load BIOS Defaults V. SOFTWARE Using DMI Utility You can load the BIOS defaults from a MIFD file and can clear all user modified and added data.
VI. ASUS PCI SCSI Cards VI. ASUS SCSI Cards SCSI BIOS Symbios SCSI BIOS and Drivers Aside from the system BIOS, the Flash memory chip on the motherboard also contains the Symbios SCSI BIOS. This Symbios SCSI BIOS works in conjunction with the optional ASUS PCI-SC200 controller card to provide Fast SCSI-2 interface when using compatible SCSI devices or the ASUS PCI-SC860 SCSI controller cards to provide Ultra-Fast SCSI-2 interface when using Ultra-Fast SCSI-2 devices.
VI. ASUS PCI SCSI Cards VI. ASUS SCSI Cards Setup Setting Up the ASUS PCI-SC200 & PCI-SC860 There are two jumper settings you may need to make on the ASUS PCI-SC200 to set it up. One setting assigns the PCI INT interrupt, the other sets the card’s termination. The ASUS PCI-SC860 has no jumper settings but you should read the “Terminator Requirements.” Setting the INT Assignment for the ASUS PCI-SC200 You must use PCI INT A setting in order to properly assign the ASUS PCI-SC200’s interrupt.
VI. ASUS PCI SCSI Cards VI. ASUS SCSI Cards Terminator Settings Terminator Settings for the ASUS PCI-SC860 Many SCSI devices including the ASUS PCI-SC860 use a set of onboard active resistors to terminate the devices at the ends automatically. Automatic termination requires that the SCSI devices be connected in a straight linear connection or “chain.” Connect SCSI devices to one or two of the SCSI connectors in a linear “chain” for auto termination of the ASUS PCI-SC860 to be effective.
VI. ASUS PCI SCSI Cards VI.
VII. ASUS LAN Card VII. ASUS LAN Card PCI-L101 LAN Card ASUS PCI-L101 Fast Ethernet Card LEDs LAN Activity Output Signal Intel Chipset RJ45 Wake on LAN Output Signal ASUS Motherboard type Other If you are using the ASUS PCI-L101 on an ASUS motherboard, leave the jumper on its defaut setting of “ASUS.” If you are using another brand of motherboard, set the jumper to “Other.
VII. ASUS LAN Card Features VII. ASUS LAN Card Features • • • • • • • • • • • • Intel 82558 Ethernet LAN Controller (Fully integrated 10BASE-T/100BASE-TX) Wake-On-LAN Remote Control Function Supported PCI Bus Master Complies to PCI Local Bus Rev. 2.1 specifications Consists of MAC & PHY (10/100Mbps) interfaces Complies to IEEE 802.3 10BASE-T and IEEE 802.3u 100BASE-TX interfaces Fully supports 10BASE-T & 100BASE-TX operations through a single RJ45 port Supports 32-bit Bus Master Technology / PCI Rev. 2.
