E593 S370-DL CPU Card Installation Guide ®
ASUS Technical Support Information ASUSTeK COMPUTER INC. (Asia-Pacific) MB/Accessories (Tel): +886-2-2890-7121 (English) Fax: +886-2-2895-9254 Email: tsd@asus.com.tw WWW: www.asus.com.tw FTP: ftp.asus.com.tw/pub/ASUS ASUS COMPUTER INTERNATIONAL (America) Fax: Email: WWW: FTP: +1-510-608-4555 tsd@asus.com www.asus.com ftp.asus.com/Pub/ASUS ASUS COMPUTER GmbH (Europe) Hotline: Fax: Email: WWW: FTP: 2 MB/Accessories: +49-2102-9599-0 +49-2102-9599-11 www.asuscom.de/de/support (for online support) www.
Introduction The ASUS S370-DL CPU card allows Slot 1 motherboards to accept socket 370 processors with Front Side Bus running at up to 133MHz. The S370DL CPU card supports single Coppermine/Celeron and dual Coppermine/ Celeron (PPGA only) processors to give Slot 1 motherboard owners an inexpensive way to upgrade their Pentium II/III computers using lower costing socket 370 processors. Since socket 370 processors are designed on the Pentium II/III design, the only difference is the package form factor.
S370-DL CPU Card ASUS S370-DL CPU Card CPU Voltage Jumpers Socket 370 Retainer Fin Slot 1 Compatible Connector 4 ASUS S370-DL Installation Guide
Windows 98 Using the S370-DL CPU card The general procedure for using the ASUS S370-DL CPU card: 1. Check the voltage setting for your socket 370 processor using the jumpers on the card if necessary. For current socket 370 processors, the default setting should be used. 2. Install the socket 370 processor. Lift the brown lever to 90° to install the processor and lower the brown lever to lock the processor. 3. Install the CPU fan heatsink. 4. Mount the ASUS S370-DL CPU card over Slot 1 on the motherboard.
Setting up the S370-DL CPU card Setting the CPU voltage is not necessary for current socket 370 processors. If required, your socket 370 processor should have its voltage requirement printed on its surface or documentation. If no voltage is indicated or you are not sure, use the “CPU Def.” setting as shown on the next page. Notice that JP7 should be configured to distinguish between Coppermine and Celeron processors.
Setting up the S370-DL CPU card 4 4 3 3 2 2 JP7 1 JP7 1 Using Coppermine Processors Using Celeron Processors (Default) 1 2 3 1 2 3 1 2 3 1 2 3 1 2 3 1 2 3 1 2 3 1 2 3 1 2 3 1 2 3 JP5 JP4 JP3 JP2 JP1 1.50Volts 1.55Volts 1.60Volts 1.65Volts 1.70Volts 1.75Volts 1.80Volts 1.85Volts 1.90Volts 1.95Volts 1 2 3 1 2 3 1 2 3 1 2 3 1 2 3 1 2 3 1 2 3 1 2 3 1 2 3 JP5 JP4 JP3 JP2 JP1 2.00Volts 2.05Volts 2.10Volts 2.20Volts 2.30Volts 2.40Volts 2.50Volts 2.60Volts CPU Def.
® S370-DL CPU Card P/N 15-xxxxxxxxx
