User’s Manual
Table Of Contents
- About this guide
- Chapter 1: Getting Started
- Chapter 2: Main Menu Overview
- Chapter 3: Deploy Management
- 3.1 Agent Management overview
- 3.2 Deploying agents
- 3.2.1 Automatically scanning and deploying to devices
- 3.2.2 Scanning an IP range
- 3.2.3 Adding and deploying to devices
- 3.2.4 Editing device information
- 3.2.5 Installing agents manually
- 3.2.6 Installing Agents in silent mode
- 3.2.7 Upgrading or repairing agents
- 3.2.8 Setting up a Windows 7 deployment environment
- 3.3 Removing agents
- 3.4 Client Agent Updater
- Chapter 4: Device Information
- Chapter 5: Management Functions
- 5.1 Metadata Management
- 5.2 Software Management
- 5.3 Task Scheduler
- 5.4 OOB Control
- 5.5 Management Control Overview
- 5.6 Management Control Information Overview
- 5.7 DASH Management Control Information
- 5.8 RTL8117 Management Control Information
- 5.9 vPro Management Control Information
- 5.10 BMC Management Control Information
- 5.10.1 Hardware Sensor
- 5.10.2 Inventory
- 5.10.3 Control
- 5.10.4 Remote Desktop
- 5.10.5 Smart BIOS
- 5.10.6 Firmware Update
- 5.10.7 Event Log
- 5.10.8 IPMI
- 5.10.9 IPMI Serial-over-LAN (SOL)
- 5.10.10 Settings
- 5.10.11 Configuration
- 5.10.12 FRU Information
- 5.10.13 Image Redirection
- 5.10.14 Platform Event Filters
- 5.10.15 BSOD Capture
- 5.10.16 Error Codes
- 5.11 Screen Broadcast
- Chapter 6: Settings Migrator
- Chapter 7: Report Generator
- Chapter 8: Account & General Settings
2-13ASUS Control Center Express
Restart Computer to
IDE-R CDROM
Set the selected device(s) to enter IDE-R ODD after a restart
through the remote management controller.
Power On to IDE-R
CDROM
Set the selected device(s) to enter IDE-R ODD after powering
on through the remote management controller.
Sleep - Light (G1/S2)
Set the selected device(s) to enter sleep mode (G1/S2)
through the remote management controller.
Power Cycle - Hard
Off (G3)
Power off and restart the selected device(s) through the
remote management controller.
Diagnostic Interrupt
(NMI)
Set the selected device(s) to print error report and restarting
through the remote management controller.
Power Off - Soft
Graceful (G2/S5)
Normal shut down via the OS of the selected device(s)
through the remote management controller.
Power Off - Hard
Graceful (G3)
Normal shut down via the hardware of the selected device(s)
through the remote management controller.
Master Bus Reset
Graceful
Normal shut down and resetting the hardware of the selected
device(s) through the remote management controller.
Power Cycle
(Graceful Soft Off)
(G2/S5)
Normal shut down via the OS then restarting the selected
device(s) through the remote management controller.
Power Cycle
(Graceful Hard Off)
(G3)
Normal shut down via the hardware then restarting the
selected device(s) through the remote management
controller.
• Power control (continued)
• Watchdog
Watchdog Enable
Enable RTL8117 Watchdog monitoring for selected device(s).
Watchdog Disable
Disable RTL8117 Watchdog monitoring for selected
device(s).
• BIOS
Clear CMOS
Clear CMOS for selected device(s) through RTL8117 or BMC
to reset them to factory settings.
• Account management
Set password
Setting the remote management controller account password
for selected RTL8117 or vPro device(s).
Login
Log into the remote management controller account of
selected BMC or DASH device(s).