User’s Manual
Table Of Contents
- About this guide
- Chapter 1: Getting Started
- Chapter 2: Main Menu Overview
- Chapter 3: Deploy Management
- 3.1 Agent Management overview
- 3.2 Deploying agents
- 3.2.1 Automatically scanning and deploying to devices
- 3.2.2 Scanning an IP range
- 3.2.3 Adding and deploying to devices
- 3.2.4 Editing device information
- 3.2.5 Installing agents manually
- 3.2.6 Installing Agents in silent mode
- 3.2.7 Upgrading or repairing agents
- 3.2.8 Setting up a Windows 7 deployment environment
- 3.3 Removing agents
- 3.4 Client Agent Updater
- Chapter 4: Device Information
- Chapter 5: Management Functions
- 5.1 Metadata Management
- 5.2 Software Management
- 5.3 Task Scheduler
- 5.4 OOB Control
- 5.5 Management Control Overview
- 5.6 Management Control Information Overview
- 5.7 DASH Management Control Information
- 5.8 RTL8117 Management Control Information
- 5.9 vPro Management Control Information
- 5.10 BMC Management Control Information
- 5.10.1 Hardware Sensor
- 5.10.2 Inventory
- 5.10.3 Control
- 5.10.4 Remote Desktop
- 5.10.5 Smart BIOS
- 5.10.6 Firmware Update
- 5.10.7 Event Log
- 5.10.8 IPMI
- 5.10.9 IPMI Serial-over-LAN (SOL)
- 5.10.10 Settings
- 5.10.11 Configuration
- 5.10.12 FRU Information
- 5.10.13 Image Redirection
- 5.10.14 Platform Event Filters
- 5.10.15 BSOD Capture
- 5.10.16 Error Codes
- 5.11 Screen Broadcast
- Chapter 6: Settings Migrator
- Chapter 7: Report Generator
- Chapter 8: Account & General Settings
5-37ASUS Control Center Express
* These Action Categories are only supported on motherboards which support remote management controllers.
Action type Action options Description
Power
Control
Power On (G0/S0) Power on device
Power Off -
Soft (G2/S5)
Power off device
Power Off - Hard (G3) Force device to power off .
Power Cycle -
Soft off (G2/S5)
Restart device after shutting down the OS
Sleep - Deep (G1/S3) Enter sleep mode (G1/S3)
Master Bus Reset Reset the hardware
Hibernate (G1/S4) Enter hibernate mode (G1/S4)
Restart Computer to
BIOS
Enter BIOS after restarting device
Power On to BIOS Enter BIOS after powering on device
Restart Computer to
IDE-R Floppy
Enter IDE-R floppy drive after restarting device
Power On to IDE-R
Floppy
Enter IDE-R floppy drive after powering on device
Restart Computer to
IDE-R CDROM
Enter IDE-R ODD after restarting device
Power On to IDE-R
CDROM
Enter IDE-R ODD after powering on device
Sleep - Light (G1/S2) Enter sleep mode (G1/S2)
Power Cycle -
Hard Off (G3)
Restart device after forcing device to power off.
Diagnostic Interrupt
(NMI)
Print error report and restarting device
Power Off - Soft
Graceful (G2/S5)
Normal shut down via the OS
Power Off - Hard
Graceful (G3)
Normal shut down via the hardware
Master Bus Reset
Graceful
Normal shut down and resetting the hardware
Power Cycle (Graceful
Soft Off) (G2/S5)
Normal shut down via the OS then restarting the
device
Power Cycle (Graceful
Hard Off) (G3)
Normal shut down via the hardware then restarting
the device
DASH