User’s Manual
Table Of Contents
- About this guide
- Chapter 1: Getting Started
- Chapter 2: Main Menu Overview
- Chapter 3: Deploy Management
- 3.1 Agent Management overview
- 3.2 Deploying agents
- 3.2.1 Automatically scanning and deploying to devices
- 3.2.2 Scanning an IP range
- 3.2.3 Adding and deploying to devices
- 3.2.4 Editing device information
- 3.2.5 Installing Agents manually
- 3.2.6 Installing Agents in silent mode
- 3.2.7 Upgrading older versions of agents or repairing agents
- 3.2.8 Setting up a Windows 7 deployment environment
- 3.3 Removing agents
- 3.4 Client Agent Updater
- Chapter 4: Device Information
- Chapter 5: Management Functions
- 5.1 Metadata Management
- 5.2 Software Management
- 5.3 Task Scheduler
- 5.4 OOB Control
- 5.5 Management Control Overview
- 5.6 Management Control Information Overview
- 5.7 DASH Management Control Information
- 5.8 RTL8117 Management Control Information
- 5.9 vPro Management Control Information
- 5.10 BMC Management Control Information
- 5.10.1 Hardware Sensor
- 5.10.2 Inventory
- 5.10.3 Control
- 5.10.4 Remote Desktop
- 5.10.5 Smart BIOS
- 5.10.6 Firmware Update
- 5.10.7 Event Log
- 5.10.8 IPMI
- 5.10.9 IPMI Serial-over-LAN (SOL)
- 5.10.10 Settings
- 5.10.11 Configuration
- 5.10.12 FRU Information
- 5.10.13 Image Redirection
- 5.10.14 Platform Event Filters
- 5.10.14 BSOD Capture
- 5.11 Screen Broadcast
- Chapter 6: Settings Migrator
- Chapter 7: Report Generator
- Chapter 8: Account & General Settings
2-12 Chapter 2: Main Menu Overview
OOB-Control*
Power
Control
Restart Computer
to IDE-R CDROM
Set the selected device(s) to enter
IDE-R ODD after a restart through
the remote management controller.
Power On to
IDE-R CDROM
Set the selected device(s) to enter
IDE-R ODD after powering on
through the remote management
controller.
Sleep - Light (G1/
S2)
Set the selected device(s) to enter
sleep mode (G1/S2) through the
remote management controller.
Power Cycle -
Hard Off (G3)
Power off and restart the selected
device(s) through the remote
management controller.
Diagnostic
Interrupt (NMI)
Set the selected device(s) to print
error report and restarting through
the remote management controller.
Power Off - Soft
Graceful (G2/S5)
Normal shut down via the OS of
the selected device(s) through the
remote management controller.
Power Off - Hard
Graceful (G3)
Normal shut down via the hardware
of the selected device(s) through
the remote management controller.
Master Bus Reset
Graceful
Normal shut down and resetting
the hardware of the selected
device(s) through the remote
management controller.
Power Cycle
(Graceful Soft
Off) (G2/S5)
Normal shut down via the OS then
restarting the selected device(s)
through the remote management
controller.
Power Cycle
(Graceful Hard
Off) (G3)
Normal shut down via the
hardware then restarting the
selected device(s) through the
remote management controller.
Watchdo``
WatchDog Enable
Enable RTL8117 WatchDog
monitoring for selected device(s).
WatchDog
Disable
Disable RTL8117 WatchDog
monitoring for selected device(s).
BIOS
Clear CMOS
Clear CMOS for selected device(s)
through RTL8117 or BMC to reset
them to factory settings.
(continued on the next page)