User’s Manual
Table Of Contents
- About this guide
- Chapter 1: Getting Started
- Chapter 2: Main Menu Overview
- Chapter 3: Deploy Management
- 3.1 Agent Management overview
- 3.2 Deploying agents
- 3.2.1 Automatically scanning and deploying to devices
- 3.2.2 Scanning an IP range
- 3.2.3 Adding and deploying to devices
- 3.2.4 Editing device information
- 3.2.5 Installing Agents manually
- 3.2.6 Installing Agents in silent mode
- 3.2.7 Upgrading older versions of agents or repairing agents
- 3.2.8 Setting up a Windows 7 deployment environment
- 3.3 Removing agents
- 3.4 Client Agent Updater
- Chapter 4: Device Information
- Chapter 5: Management Functions
- 5.1 Metadata Management
- 5.2 Software Management
- 5.3 Task Scheduler
- 5.4 OOB Control
- 5.5 Management Control Overview
- 5.6 Management Control Information Overview
- 5.7 DASH Management Control Information
- 5.8 RTL8117 Management Control Information
- 5.9 vPro Management Control Information
- 5.10 BMC Management Control Information
- 5.10.1 Hardware Sensor
- 5.10.2 Inventory
- 5.10.3 Control
- 5.10.4 Remote Desktop
- 5.10.5 Smart BIOS
- 5.10.6 Firmware Update
- 5.10.7 Event Log
- 5.10.8 IPMI
- 5.10.9 IPMI Serial-over-LAN (SOL)
- 5.10.10 Settings
- 5.10.11 Configuration
- 5.10.12 FRU Information
- 5.10.13 Image Redirection
- 5.10.14 Platform Event Filters
- 5.10.14 BSOD Capture
- 5.11 Screen Broadcast
- Chapter 6: Settings Migrator
- Chapter 7: Report Generator
- Chapter 8: Account & General Settings
2-11ASUS Control Center Express
(continued on the next page)
Remote Control
Restart Computer
Restart the selected device(s).
Power Off
Power off the selected device(s).
Power On
Power on the selected device(s).
A powered off client
device can only
be powered on if it
supports Wake on
LAN.
OOB-Control*
Power
Control
Power On
(G0/S0)
Power on the selected device(s)
through the remote management
controller.
Power Off - Soft
(G2/S5)
Power off the selected device(s)
through the remote management
controller.
Power Off - Hard
(G3)
Force a power off of the selected
device(s) through the remote
management controller.
Power Cycle -
Soft off (G2/S5)
Set the selected device(s) to
restart after shutting down the OS
through the remote management
controller.
Sleep - Deep (G1/
S3)
Set the selected device(s) to enter
sleep mode (G1/S3) through the
remote management controller.
Master Bus Reset
Reset the hardware of the selected
device(s) through the remote
management controller.
Hibernate
(G1/S4)
Set the selected device(s) to enter
hibernate mode (G1/S4) through
the remote management controller.
Restart Computer
to BIOS
Set the selected device(s) to enter
BIOS after a restart through the
remote management controller.
Power On to
BIOS
Set the selected device(s) to enter
BIOS after powering on through
the remote management controller.
Restart Computer
to IDE-R Floppy
Set the selected device(s) to enter
IDE-R floppy drive after a restart
through the remote management
controller.
Power On to
IDE-R Floppy
Set the selected device(s) to
enter IDE-R floppy drive after
powering on through the remote
management controller.