User’s Manual
Table Of Contents
- About this guide
- Chapter 1: Getting Started
- Chapter 2: Main Menu Overview
- Chapter 3: Deploy Management
- 3.1 Agent Management overview
- 3.2 Deploying agents
- 3.2.1 Automatically scanning and deploying to devices
- 3.2.2 Scanning an IP range
- 3.2.3 Adding and deploying to devices
- 3.2.4 Editing device information
- 3.2.5 Installing Agents manually
- 3.2.6 Installing Agents in silent mode
- 3.2.7 Upgrading older versions of agents or repairing agents
- 3.2.8 Setting up a Windows 7 deployment environment
- 3.3 Removing agents
- 3.4 Client Agent Updater
- Chapter 4: Device Information
- Chapter 5: Management Functions
- 5.1 Metadata Management
- 5.2 Software Management
- 5.3 Task Scheduler
- 5.4 OOB Control
- 5.5 Management Control Overview
- 5.6 Management Control Information Overview
- 5.7 DASH Management Control Information
- 5.8 RTL8117 Management Control Information
- 5.9 vPro Management Control Information
- 5.10 BMC Management Control Information
- 5.10.1 Hardware Sensor
- 5.10.2 Inventory
- 5.10.3 Control
- 5.10.4 Remote Desktop
- 5.10.5 Smart BIOS
- 5.10.6 Firmware Update
- 5.10.7 Event Log
- 5.10.8 IPMI
- 5.10.9 IPMI Serial-over-LAN (SOL)
- 5.10.10 Settings
- 5.10.11 Configuration
- 5.10.12 FRU Information
- 5.10.13 Image Redirection
- 5.10.14 Platform Event Filters
- 5.10.14 BSOD Capture
- 5.11 Screen Broadcast
- Chapter 6: Settings Migrator
- Chapter 7: Report Generator
- Chapter 8: Account & General Settings
5-150 Chapter 5: Management Functions
IPv4 Subnet*
Set the static subnet mask.
IPv4 Gateway*
Set the static default gateway.
Enable IPv6
Enable or disable IPv6 for the selected interface.
Enable IPv6 DHCP
Enable or disable dynamic configuration of IPv6
addresses using Dynamic Host Configuration Protocol
(DHCP)
IPv6 Index*
Set the IPv6 Index.
IPv6 Address*
Set the static IPv6 Address.
Subnet Prefix Length*
Set the IPv6 Subnet Prefix length
IPv6 Gateway*
Set the IPv6 Gateway
Enable VLAN
Enable or disable VLAN support for the selected
interface.
VLAN ID
Set the VLAN ID.
VLAN Priority
Set the VLAN priority.
Settings marked with an asterisk (*) are only available when
IPv4/IPv6
is
enabled and
DHCP
is disabled.
Network DNS Configuration
This item will allow you manage DNS settings.
DNS Enabled
Enable or disable the DNS service.
mDNS Enabled
Enable or disable Multicast DNS.
Host Name Setting
Set Host Name configuration to Auto or Manual.
Host Name
Set the Host Name if it is not configured automatically.
BMC Interface
Shows the BMC Interface name.
Register BMC
Enable or disable BMC registration.
Registration Method
Select from the following registration methods:
- Nsupdate: Register with the DNS server using the
nsupdate application.
- DHCP Client FQDN: Register with the DNS server
using DHCP option 81.
-
Hostname
: Register with the DNS server using
DHCP option 12.
TSIG Authentication Enabled
Enable or disable TSIG authentication
Current TSIG Private File Info
Shows the date and time of the current TSIG Private
File if TSIG Authentication is enabled.
New TSIG Private File
Select a new TSIG Private File to upload if TSIG
Authentication is enabled.
(continued on the next page)