User’s Manual
Table Of Contents
- About this guide
- Chapter 1: Getting Started
- Chapter 2: Main Menu Overview
- Chapter 3: Deploy Management
- 3.1 Agent Management overview
- 3.2 Deploying agents
- 3.2.1 Automatically scanning and deploying to devices
- 3.2.2 Scanning an IP range
- 3.2.3 Adding and deploying to devices
- 3.2.4 Editing device information
- 3.2.5 Installing Agents manually
- 3.2.6 Installing Agents in silent mode
- 3.2.7 Upgrading older versions of agents or repairing agents
- 3.2.8 Setting up a Windows 7 deployment environment
- 3.3 Removing agents
- 3.4 Client Agent Updater
- Chapter 4: Device Information
- Chapter 5: Management Functions
- 5.1 Metadata Management
- 5.2 Software Management
- 5.3 Task Scheduler
- 5.4 OOB Control
- 5.5 Management Control Overview
- 5.6 Management Control Information Overview
- 5.7 DASH Management Control Information
- 5.8 RTL8117 Management Control Information
- 5.9 vPro Management Control Information
- 5.10 BMC Management Control Information
- 5.10.1 Hardware Sensor
- 5.10.2 Inventory
- 5.10.3 Control
- 5.10.4 Remote Desktop
- 5.10.5 Smart BIOS
- 5.10.6 Firmware Update
- 5.10.7 Event Log
- 5.10.8 IPMI
- 5.10.9 IPMI Serial-over-LAN (SOL)
- 5.10.10 Settings
- 5.10.11 Configuration
- 5.10.12 FRU Information
- 5.10.13 Image Redirection
- 5.10.14 Platform Event Filters
- 5.10.14 BSOD Capture
- 5.11 Screen Broadcast
- Chapter 6: Settings Migrator
- Chapter 7: Report Generator
- Chapter 8: Account & General Settings
5-50 Chapter 5: Management Functions
5.4.2 Using OOB - Control functions
To use the OOB - Control functions you can either:
• Select the client device(s) you would like to execute OOB - Control functions
on, then click on
Select Function
>
OOB - Control
and select a function to
use.
• Click on then perform a
Scan
or
Scan IP Range
, select the client
device(s) you would like to execute OOB - Control functions on, then click on
Select Function
and select a function to use.
Please see the table below for the list of the OOB - Control functions available for
the different remote management controllers:
Functions List BMC DASH
RTL
8117
vPro
Power
Control
Power On (G0/S0)
V V V V
Power Off - Soft (G2/S5)
V V V V
Power Off - Hard (G3)
V V V V
Power Cycle - Soft off (G2/S5)
V V V V
Sleep - Deep (G1/S3)
V V
Master Bus Reset
V V
Hibernate (G1/S4)
V V
Restart Computer to BIOS
V
Power On to BIOS
V
Restart Computer to IDE-R Floppy
V
Power On to IDE-R Floppy
V
Restart Computer to IDE-R CDROM
V
Power On to IDE-R CDROM
V
Sleep - Light (G1/S2)
V
Power Cycle - Hard Off (G3)
V V
Diagnostic Interrupt (NMI)
V
Power Off - Soft Graceful (G2/S5)
V
Power Off - Hard Graceful (G3)
V
Master Bus Reset Graceful
V
Power Cycle (Graceful Soft Off) (G2/S5)
V
Power Cycle (Graceful Hard Off) (G3)
V
WatchDog
WatchDog Enable
V
WatchDog Disable
V
BIOS
Smart BIOS
V V
Clear CMOS
V V
Account
Management
Set Password
V V
Login
V V
(continued on the next page)