User’s Manual
Table Of Contents
- About this guide
- Chapter 1: Getting Started
- Chapter 2: Main Menu Overview
- Chapter 3: Deploy Management
- 3.1 Agent Management overview
- 3.2 Deploying agents
- 3.2.1 Automatically scanning and deploying to devices
- 3.2.2 Scanning an IP range
- 3.2.3 Adding and deploying to devices
- 3.2.4 Editing device information
- 3.2.5 Installing Agents manually
- 3.2.6 Installing Agents in silent mode
- 3.2.7 Upgrading older versions of agents or repairing agents
- 3.2.8 Setting up a Windows 7 deployment environment
- 3.3 Removing agents
- 3.4 Client Agent Updater
- Chapter 4: Device Information
- Chapter 5: Management Functions
- 5.1 Metadata Management
- 5.2 Software Management
- 5.3 Task Scheduler
- 5.4 OOB Control
- 5.5 Management Control Overview
- 5.6 Management Control Information Overview
- 5.7 DASH Management Control Information
- 5.8 RTL8117 Management Control Information
- 5.9 vPro Management Control Information
- 5.10 BMC Management Control Information
- 5.10.1 Hardware Sensor
- 5.10.2 Inventory
- 5.10.3 Control
- 5.10.4 Remote Desktop
- 5.10.5 Smart BIOS
- 5.10.6 Firmware Update
- 5.10.7 Event Log
- 5.10.8 IPMI
- 5.10.9 IPMI Serial-over-LAN (SOL)
- 5.10.10 Settings
- 5.10.11 Configuration
- 5.10.12 FRU Information
- 5.10.13 Image Redirection
- 5.10.14 Platform Event Filters
- 5.10.14 BSOD Capture
- 5.11 Screen Broadcast
- Chapter 6: Settings Migrator
- Chapter 7: Report Generator
- Chapter 8: Account & General Settings
5-35ASUS Control Center Express
Action
Category
Action type Action options Description
Software
Power
Control
Power Off Power off device
Power On Power on device
Power Reboot Restart device
Service
Control
Service Name Enter the name of the service
Start Start the service
Stop Stop the service
Restart Restart the service
Software
Dispatch
Package Name
Select a software package from the
Software Pool
Security
Control
Registry
Tool
Enable Enable Windows Registry Editor
Disable Disable Windows Registry Editor
USB
Control
Enable Enable the USB ports
Disable Disable the USB ports
Read Only Set the USB to Read Only privileges
BIOS Cache
BIOS Cache List
Select a BIOS file from the BIOS
cache list
Hardware*
Power
Control
Power Off Power off device
Force Power Off Force power off device
Power On Power on device
Power Reboot Restart device
Enable /
Disable
WatchDog
Heartbeat Interval Set the heartbeat interval
Enable Enable Watchdog
Disable Disable Watchdog
Clear CMOS
- Clear the CMOS of device
Enable /
Disable KVM
Enable Enable KVM
Disable Disable KVM
DASH*
Power
Control
Power On (G0/S0) Power on device
Power Off -
Soft (G2/S5)
Power off device
Power Off - Hard (G3) Force device to power off .
Power Cycle -
Soft off (G2/S5)
Restart device after shutting down the
OS
Sleep - Deep (G1/S3) Enter sleep mode (G1/S3)
Master Bus Reset Reset the hardware
Hibernate (G1/S4) Enter hibernate mode (G1/S4)
Restart Computer to
BIOS
Enter BIOS after restarting device
Power On to BIOS Enter BIOS after powering on device
Restart Computer to
IDE-R Floppy
Enter IDE-R floppy drive after
restarting device
Power On to IDE-R
Floppy
Enter IDE-R floppy drive after
powering on device
(continued on the next page)