User Manual
Table Of Contents
- 1. Knowing BIOS
- 2. BIOS setup program
- 3. Managing and updating your BIOS
- 4. BIOS menu screen
- 5. Main menu
- 6. Ai Tweaker menu
- 7. Advanced menu
- 7.1 Trusted Computing
- 7.2 AMD fTPM configuration
- 7.3 Redfish Host Interface Settings
- 7.4 UEFI Variables Protection
- 7.5 Serial Port Console Redirection
- 7.6 CPU Configuration
- 7.7 PCI Subsystem Settings
- 7.8 USB Configuration
- 7.9 Network Stack Configuration
- 7.10 NVMe Configuration
- 7.11 HDD/SSD SMART Information
- 7.12 SATA Configuration
- 7.13 APM Configuration
- 7.14 Onboard Devices Configuration
- 7.15 PCIe Redriver Tuning
- 7.16 AMD Mem Configuration Status
- 7.17 AMD PBS
- 7.18 AMD Overclocking
- 7.19 AMD CBS
- 7.20 Third-party UEFI driver configurations
- 8. Monitor menu
- 9. Boot menu
- 10. Tool menu
- 11. Server Mgmt menu
- 12. Exit menu
Pro WS sTR5 Series BIOS Manual
73
CXL Sublink interleaving
Allows you to enable or disable CXL sublink interleaving.
Configuration options: [Enabled] [Disabled] [Auto]
1TB remap
Attempt to remap DRAM out of the space just below the 1TB boundary. The ability to
remap depends on DRAM configuration, NPS, and interleaving selection, and may not
always be possible.
Configuration options: [Do not remap] [Attempt to remap] [Auto]
DRAM map inversion
Inverting the map will cause the highest memory channels to get assigned the lowest
addresses in the system.
Configuration options: [Disabled] [Enabled] [Auto]
Location of private memory regions
Controls whether or not the private memory regions (PSP, SMU, and CC6) are at the top
of DRAM or distributed. Note that distributed requires memory on all dies. Note that it will
always be at the top of DRAM id some dies don’t have memory regardless of this option’s
setting.
Configuration options: [Distributed] [Consolidated] [Consolidated to 1st DRAM pair] [Auto]
ACPI
ACPI SRAT L3 Cache as NUMA Domain
[Disabled] Memory Addressing \ NUMA nodes per socket will be declared.
[Enabled] Each CCX in the system will be declared as a separate NUMA
domain.
[Auto] Sets to the default option.
ACPI SLIT Distance Control
This option determines how the SLIT distances are declared.
Configuration options: [Manual] [Auto]
The following item appears only when ACPI SLIT Distance Control is set to [Auto].
ACPI SLIT remote relative distance
Allows you to set the remote socket distance for 2P systems as near (2.8) or far (3.2).
Configuration options: [Near] [Far] [Auto]
The following items appear only when ACPI SLIT Distance Control is set to [Manual].
ACPI SLIT same socket distance
Specify the distance to other physical domains within the same socket.
Configuration options: [10] - [255]
ACPI SLIT remote socket distance
Specify the distance to domains the remote socket.
Configuration options: [10] - [255]
ACPI SLIT local SLink distance
Specify the distance to an SLink domain on the same socket.
Configuration options: [10] - [255]
ACPI SLIT remote SLink distance
Specify the distance to an SLink domain on the other socket.
Configuration options: [10] - [255]
ACPI SLIT local inter-SLink distance
Specify the distance between two SLink domains on the same socket.
Configuration options: [10] - [255]