User Manual
Table Of Contents
- 1. Knowing BIOS
- 2. BIOS setup program
- 3. Managing and updating your BIOS
- 4. BIOS menu screen
- 5. Main menu
- 6. Ai Tweaker menu
- 7. Advanced menu
- 7.1 Trusted Computing
- 7.2 AMD fTPM configuration
- 7.3 Redfish Host Interface Settings
- 7.4 UEFI Variables Protection
- 7.5 Serial Port Console Redirection
- 7.6 CPU Configuration
- 7.7 PCI Subsystem Settings
- 7.8 USB Configuration
- 7.9 Network Stack Configuration
- 7.10 NVMe Configuration
- 7.11 HDD/SSD SMART Information
- 7.12 SATA Configuration
- 7.13 APM Configuration
- 7.14 Onboard Devices Configuration
- 7.15 PCIe Redriver Tuning
- 7.16 AMD Mem Configuration Status
- 7.17 AMD PBS
- 7.18 AMD Overclocking
- 7.19 AMD CBS
- 7.20 Third-party UEFI driver configurations
- 8. Monitor menu
- 9. Boot menu
- 10. Tool menu
- 11. Server Mgmt menu
- 12. Exit menu
62
Pro WS sTR5 Series BIOS Manual
Dram ODT impedance RTT_NOM_WR
Specifies the DRAM ODT impedance RTT_NOM_WR.
Configuration options: [Auto] [RTT_OFF] [RZQ (240)] [RZQ/2 (120)] [RZQ/3
(80)] [RZQ/4 (60)] [RZQ/5 (48)] [RZQ/6 (40)] [RZQ/7 (34)]
Dram ODT impedance RTT_NOM_RD
Specifies the DRAM ODT impedance RTT_NOM_RD.
Configuration options: [Auto] [RTT_OFF] [RZQ (240)] [RZQ/2 (120)] [RZQ/3
(80)] [RZQ/4 (60)] [RZQ/5 (48)] [RZQ/6 (40)] [RZQ/7 (34)]
Dram ODT impedance RTT_WR
Specifies the DRAM ODT impedance RTT_WR.
Configuration options: [Auto] [RTT_OFF] [RZQ (240)] [RZQ/2 (120)] [RZQ/3
(80)] [RZQ/4 (60)] [RZQ/5 (48)] [RZQ/6 (40)] [RZQ/7 (34)]
Dram ODT impedance RTT_PARK
Specifies the DRAM ODT impedance RTT_PARK.
Configuration options: [Auto] [RTT_OFF] [RZQ (240)] [RZQ/2 (120)] [RZQ/3
(80)] [RZQ/4 (60)] [RZQ/5 (48)] [RZQ/6 (40)] [RZQ/7 (34)]
Dram ODT impedance DQS_RTT_PARK
Specifies the DRAM ODT impedance DQS_RTT_PARK.
Configuration options: [Auto] [RTT_OFF] [RZQ (240)] [RZQ/2 (120)] [RZQ/3
(80)] [RZQ/4 (60)] [RZQ/5 (48)] [RZQ/6 (40)] [RZQ/7 (34)]
DDR Controller Configuration
DDR Power Options
Power Down Enable
Allows you to enable or disable DDR power down mode.
Configuration options: [Disabled] [Enabled] [Auto]
Additional Memory Tweaks
RX DFE Taps
Allows you to specify the number of RX DFE taps, Value only applies
when RX2D_DFE is enabled.
Configuration options: [Auto] [1 Tap] [2 Tap] [3 Tap] [4 Tap]
TX DFE Taps
Allows you to specify the number of TX DFE taps, Value only applies
when TX2D_DFE is enabled.
Configuration options: [Auto] [1 Tap] [2 Tap] [3 Tap] [4 Tap]
Infinity Fabric Frequency and Dividers
Infinity Fabric Frequency and Dividers
Allows you to set Infinity Fabric Frequency (FCLK). Auto = FCLK = MCLK. Manual =
FCLK must be less than MCLK for best performance in most cases. Latency penalties
are incurred if FCLK and MCLK are mismatched, but sufficiently high MCLK can negate
or overcome this penalty.
Configuration options: [Auto] [100 MHz] - [3000 MHz]
UCLK DIV1 MODE
Allows you to set UCLK DIV mode.
Configuration options: [Auto] [UCLK=MEMCLK] [UCLK=MEMCLK/2]
Precision Boost Overdrive
Precision Boost Overdrive
When this item is enabled, it allows the processor to run beyond defined values for
PPT, VDD_CPU EDC, VDD_CPU TDC, VDD_SOC EDC, VDD_SOC TDC to the limits
of the board, and allows it to boost at higher voltages for longer durations than default
operation.
Configuration options: [Auto] [Disabled] [Enabled] [Advanced]