HUAWEI EC156 User Guide
Table of Contents 1. Introduction.............................................................................................................................. 3 2. System Requirements ........................................................................................................... 3 3. EC156 Appearance................................................................................................................. 4 4. Technical Specifications ...............................................
1. Introduction Congratulations on your purchase of Huawei EC156 TATA Photon Plus USB Data Modem Device. The User Guide contains important information on the proper use and correct operation of Huawei EC156 TATA Photon Plus USB Data Modem Device. We recommend that you read this manual carefully to ensure optimal performance. 2. System Requirements PC with USB Port Hardware configuration should satisfy the demand of any of the following operating system. a.
3. EC156 Appearance 2 1 2 4 3 Please find below the description that you need to know to start using your device. Name 1.USB Plug 2.Strap Hole 3.Indicator light 4. microSD card Slot Description It connects the device to your PC. You can tie the cap and the USB Stick together by threading a strap through the strap holes, so that the cap will not be easily lost. Solid: Device is powered on. Blinking once every 2 seconds: Device is searching for a network or no network is found.
4. Technical Specifications Modem Type USB Dongle NON-RIUM Mode EVDO REV A Frequency (Band ) 800 MHz Antenna Type Internal Dimension 83.0mm×26.5mm×11.5mm Memory Card Slot Support microSD card External Memory Support Up to 4GB Up to 3.1 Mbps (Downlink) & Speeds Up to 1.8 Mbps (Uplink) NOTE: In regions, where Tata Photon Plus network coverage is unavailable, the device will operate on Tata Photon Whiz speeds of up to 153.
5. Inserting a microSD Card 1. Slide the back cover to remove it from the device. 2. Insert the microSD card into the corresponding card slot, as shown in the following figure. 3. Replace the back cover and slide it into place.
6. Using the device For different operating system, the installation process is different. Please note the process for the following Operating Systems Installation Procedure for Windows XP 1． Connect the USB Modem with PC Connect the USB Modem with your PC via USB port.
2．Install the Dialer & Driver If PC opens the auto run function, it will pop up an installation interface. If not, please go to CD as shown in the figure below and open it and double click the “AutoRun.exe” file or right click and click on Auto play.
Click “Next “and then to agree with the license agreement click “I Agree”. Click “Next “and then choose a location path for installation and click install. In case you do not have any specific location preference you may choose to continue with the default location and click “Install”.
Please click on “Finish” button.
After installation, please go back to desktop, click on the icon ”Tata Photon+” . The main interface appears When the installation is complete, the following dialer appears 1.
2. On clicking the “Continue” button, the following screen appears. Please select the Prepaid/Postpaid option depending on the services that you wish to opt for. Gently scratch the silver strip on the “Activation card” you have received with the Starter kit, to reveal your 14-digit PIN. Enter your 14 digit PIN number in text box below “Enter PIN”.
3. On clicking the “Activate” button, the following screen appears. bars indicate that the activation is in progress. The moving 4. You may have to wait for a couple of minutes.
will see the following screen 5. Click on the “Connect” button and start surfing.
1. In case activation is unsuccessful, you will see the following prompt 2. Please click on the “OK” button. The following screen will appear. Please click on the “Activate” button as shown in the below figure. Please repeat the same sequence as stated above to continue.
Un-installation of Application Software 1. 2. 3. 4. Exit Management procedures. Remove the EC156 device from the system then pull it out. Open “Add/Remove program” in the control panel. Accord the prompt, finish un-installation. Installation Procedure for Mac OS 1．Connect the USB Modem with PC Connect the USB Modem with your PC via USB port.
2．Install the Dialer & Driver Insert the Device into your PC. Double click icon of “Tata Photon+” Click “Continue” to start the installation.
Read the Software License Agreement then click “Continue”. Click “Agree” to accept the license agreement.
Click “Install”.
When installation is successful click on close button When the installation is complete, the following dialer appears 1.
2. Click on the “Connect” button and start surfing.
Un-installation of Application Software 1. Exit Management procedures. 2. Open “uninstall Mobile Partner”, click “OK” >“OK”.
Installation Procedure for Linux 1．Connect the USB Modem with PC Connect the USB Modem with your PC via USB port.
Install the Dialer & Driver Once after inserting the modem double click and open the folder. Open new terminal go to the path cd /media/Tata\ Photn+ \ \ \ \ /.
Type the command sh ./install to install Tata Photon+ dialer and press enter.
After pressing enter key you will get the below new terminal as shown below
again press enter key.
As soon as the installation is complete the default dialer will appear as follows Click on the “Connect” button and start surfing.
Un-installation of Application Software 1. Go to the installed path [eg:- /usr/local/Tata_Photon+] as shown below.
2. Type ./UninstallMobilePartner and press enter key will uninstall TataPhotn+.
7.
HP IBM Lenovo
Toshiba Sony Fujitsu
Rover Gateway Hasee
8. Troubleshooting If your radio card has abnormal conditions, please refer to the following table. Common problems Cannot automatically install the driver & Dialer tool in the first time Cannot install driver successfully Cannot find the device by Dialer tool Cannot search signal from Dialer tool Cannot connect to internet by Dialer tool Check item Maybe the computer does not open the auto run function. Please go to “My Computer”->CD Rom which name is “Tata Photon+”, open it and run the autorun.
Common problems Device is not detecting in MAC OS Device is detecting in MAC OS, But not showing signal strength Device is detecting in Linux, But not showing signal strength Insert T-Flash Card Micro-SD card is not recognized PC not able to detect Device Firewall Security Alert appears during Connection Check item Please check the drivers (HuaweiDataCardDriver.kext) are present in the following path /System/Library/Extensions . If not present please reinstall the application.
Common problems Check item After restarting the computer, there is no signal indicated Please check if the Device is connected Properly, Check the Network Coverage or pull out the Device and reinsert the Device again.
9. Care and Maintenance Your radio card is a product of superior design and craftsmanship and should be treated with care. The suggestions below will help you to fulfill any warranty obligations and to enjoy this product for many years. Keep the radio card and all its parts and accessories out of small children's reach. Keep the radio card dry. Precipitation, humidity, and all types of liquids or moisture can contain minerals that will corrode electronic circuits.
This section contains important information pertaining to the operating instructions of your device. It also contains information about how to use your device safely. Read this information carefully before using the device. Electronic Device Do not use your device if using the device is prohibited. Do not use the device when using the device causes danger or interference with electronic devices. Medical Device Follow rules and regulations set forth by hospitals and health care facilities.
locations include areas below the deck on boats, chemical transfer or storage facilities, and areas where the air contains chemicals or particles such as grain, dust, or metal powders. Ask the manufacturers of vehicles using liquefied petroleum gas (such as propane or butane) whether this device can be safely used in their vicinity. Traffic Security Observe local laws and regulations while using the device. To prevent accidents, do not use your wireless device while driving.
Operating Environment Do not use the device in dusty, damp, and dirty places or places with magnetic fields. Otherwise, it may result in malfunction of the circuit. On a stormy day with thunder, do not use your device when it is being charged, to prevent any danger caused by lightning. While using the device, observe the local laws and regulations, and respect others' privacy and legal rights. Safety of Children Comply with all precautions with regard to children's safety.
Protect your wireless device and accessories from water and vapor, and keep them dry. Do not drop, throw, or bend your wireless device. Clean your wireless device with a piece of damp and soft antistatic cloth. Do not use any chemical detergent, powder, or other chemical agents (such as alcohol and benzene) to clean the device. Keep the ambient temperature between -10℃to +45℃for using the device. Certification Information (SAR) Your wireless device is a radio transmitter and receiver.
Body Worn Operation Important safety information regarding radiofrequency (RF) radiation exposure is as follows: To ensure compliance with RF exposure guidelines, the device must be used with a minimum of 2.5cm distance from the body. Failure to observe these instructions could result in your RF exposure exceeding the relevant guideline limits.
This device generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
