User Manual
Table Of Contents
- Mellanox WinOF VPI User Manual
- Table of Contents
- List of Tables
- Document Revision History
- About this Manual
- 1 Introduction
- 2 Firmware Upgrade
- 3 Driver Features
- 3.1 Hyper-V with VMQ
- 3.2 Header Data Split
- 3.3 Receive Side Scaling (RSS)
- 3.4 Port Configuration
- 3.5 Load Balancing, Fail-Over (LBFO) and VLAN
- 3.6 Ports TX Arbitration
- 3.7 RDMA over Converged Ethernet (RoCE)
- 3.8 Network Virtualization using Generic Routing Encapsulation
- 3.9 Differentiated Services Code Point (DSCP)
- 4 Deploying Windows Server 2012 and Above with SMB Direct
- 5 Driver Configuration
- 6 Performance Tuning
- 7 OpenSM - Subnet Manager
- 8 InfiniBand Fabric
- 8.1 Network Direct Interface
- 8.2 part_man - Virtual IPoIB Port Creation Utility
- 8.3 InfiniBand Fabric Diagnostic Utilities
- 8.3.1 Utilities Usage
- 8.3.2 ibdiagnet
- 8.3.3 ibportstate
- 8.3.4 ibroute
- 8.3.5 ibdump
- 8.3.6 smpquery
- 8.3.7 perfquery
- 8.3.8 ibping
- 8.3.9 ibnetdiscover
- 8.3.10 ibtracert
- 8.3.11 sminfo
- 8.3.12 ibclearerrors
- 8.3.13 ibstat
- 8.3.14 vstat
- 8.3.15 osmtest
- 8.3.16 ibaddr
- 8.3.17 ibcacheedit
- 8.3.18 iblinkinfo
- 8.3.19 ibqueryerrors
- 8.3.20 ibsysstat
- 8.3.21 saquery
- 8.3.22 smpdump
- 8.4 InfiniBand Fabric Performance Utilities
- 8.4.1 ib_read_bw
- 8.4.2 ib_read_lat
- 8.4.3 ib_send_bw
- 8.4.4 ib_send_lat
- 8.4.5 ib_write_bw
- 8.4.6 ib_write_lat
- 8.4.7 ibv_read_bw
- 8.4.8 ibv_read_lat
- 8.4.9 ibv_send_bw
- 8.4.10 ibv_send_lat
- 8.4.11 ibv_write_bw
- 8.4.12 ibv_write_lat
- 8.4.13 nd_write_bw
- 8.4.14 nd_write_lat
- 8.4.15 nd_read_bw
- 8.4.16 nd_read_lat
- 8.4.17 nd_send_bw
- 8.4.18 nd_send_lat
- 8.4.19 NTttcp
- 9 Software Development Kit
- 10 Troubleshooting
- 11 Documentation
- Appendix A: Windows MPI (MS-MPI)
- Appendix B: NVGRE Configuration Scrips Examples
Rev 4.60
Mellanox Technologies
99
8.3.21.2 saquery Options
Table 30 - saquery Flags and Options
Flags Description
-p Gets PathRecord info.
-N Gets NodeRecord info.
--list | -D Gets NodeDescriptions of CAs only.
-S Gets ServiceRecord info.
-I Gets InformInfoRecord (subscription) info.
-L Returns the Lids of the name specified
-l Returns the unique Lid of the name speci-
fied
-G Returns the Guids of the name specified
-O Returns the name for the Lid specified
-U Returns the name for the Guid specified
-C Gets the SA’s class port info
-s Returns the PortInfoRecords with isSM or
isSMdisabled capability mask bit on.
-g Gets multicast group info
-m Gets multicast member info. If a group is
specified, limit the output to the group
specified and print one line containing only
the GUID and node description for each
entry.
Example:
saquery -m 0xc000
-x Gets LinkRecord info.
--src-to-dst Gets a PathRecord for <src:dst> where src
and dst are either node names or LIDs.
--sgid-to-dgid Gets a PathRecord for sgid to dgid where
both GIDs are in an IPv6 format acceptable
to inet_pton(3).
-C <ca_name> Uses the specified ca_name.
-P <ca_port> Uses the specified ca_port.
--smkey <val> Uses SM_Key value for the query. Will be
used only with "trusted" queries. If non-
numeric value (like’x’) is specified then
saquery will prompt for a value.