User Manual
Table Of Contents
- Mellanox WinOF VPI User Manual
- Table of Contents
- List of Tables
- Document Revision History
- About this Manual
- 1 Introduction
- 2 Firmware Upgrade
- 3 Driver Features
- 3.1 Hyper-V with VMQ
- 3.2 Header Data Split
- 3.3 Receive Side Scaling (RSS)
- 3.4 Port Configuration
- 3.5 Load Balancing, Fail-Over (LBFO) and VLAN
- 3.6 Ports TX Arbitration
- 3.7 RDMA over Converged Ethernet (RoCE)
- 3.8 Network Virtualization using Generic Routing Encapsulation
- 3.9 Differentiated Services Code Point (DSCP)
- 4 Deploying Windows Server 2012 and Above with SMB Direct
- 5 Driver Configuration
- 6 Performance Tuning
- 7 OpenSM - Subnet Manager
- 8 InfiniBand Fabric
- 8.1 Network Direct Interface
- 8.2 part_man - Virtual IPoIB Port Creation Utility
- 8.3 InfiniBand Fabric Diagnostic Utilities
- 8.3.1 Utilities Usage
- 8.3.2 ibdiagnet
- 8.3.3 ibportstate
- 8.3.4 ibroute
- 8.3.5 ibdump
- 8.3.6 smpquery
- 8.3.7 perfquery
- 8.3.8 ibping
- 8.3.9 ibnetdiscover
- 8.3.10 ibtracert
- 8.3.11 sminfo
- 8.3.12 ibclearerrors
- 8.3.13 ibstat
- 8.3.14 vstat
- 8.3.15 osmtest
- 8.3.16 ibaddr
- 8.3.17 ibcacheedit
- 8.3.18 iblinkinfo
- 8.3.19 ibqueryerrors
- 8.3.20 ibsysstat
- 8.3.21 saquery
- 8.3.22 smpdump
- 8.4 InfiniBand Fabric Performance Utilities
- 8.4.1 ib_read_bw
- 8.4.2 ib_read_lat
- 8.4.3 ib_send_bw
- 8.4.4 ib_send_lat
- 8.4.5 ib_write_bw
- 8.4.6 ib_write_lat
- 8.4.7 ibv_read_bw
- 8.4.8 ibv_read_lat
- 8.4.9 ibv_send_bw
- 8.4.10 ibv_send_lat
- 8.4.11 ibv_write_bw
- 8.4.12 ibv_write_lat
- 8.4.13 nd_write_bw
- 8.4.14 nd_write_lat
- 8.4.15 nd_read_bw
- 8.4.16 nd_read_lat
- 8.4.17 nd_send_bw
- 8.4.18 nd_send_lat
- 8.4.19 NTttcp
- 9 Software Development Kit
- 10 Troubleshooting
- 11 Documentation
- Appendix A: Windows MPI (MS-MPI)
- Appendix B: NVGRE Configuration Scrips Examples
Rev 4.60
Mellanox Technologies
90
8.3.16 ibaddr
Displays the lid (and range) as well as the GID address of the port specified (by DR path, lid, or
GUID) or the local port by default.
8.3.16.1 ibaddr Synopsis
8.3.16.2 ibaddr Options
-vf This option sets the log verbosity level. A flags field must follow
the -D option. A bit set/clear in the flags enables/disables a specific
log level as follows:
BIT LOG LEVEL ENABLED
---- -----------------
0x01 - ERROR (error messages)
0x02 - INFO (basic messages, low volume)
0x04 - VERBOSE (interesting stuff, moderate volume)
0x08 - DEBUG (diagnostic, high volume)
0x10 - FUNCS (function entry/exit, very high volume)
0x20 - FRAMES (dumps all SMP and GMP frames)
0x40 - ROUTING (dump FDB routing information)
0x80 - currently unused.
Without -vf, osmtest defaults to ERROR + INFO (0x3) Specifying -vf
0 disables all messages Specifying -vf 0xFF enables all messages (see
-V) High verbosity levels may require increasing the transaction
timeout with the -t option
-h, --help Display this usage info then exit.
This utility can be used as simple address resolver.
ibaddr [-d(ebug)] [-D(irect)] [-G(uid)] [-l(id_show)] [-g(id_show)] [-C
ca_name] [-P ca_port] [-t(imeout) timeout_ms] [-V(ersion)] [-h(elp)]
[<lid | dr_path | guid>]
Table 25 - ibaddr Flags and Options
Flags Description
-G, --Guid shows lid range and gid for GUID address
-l, --lid_show shows lid range only
-L, --Lid_show shows lid range (in decimal) only
-g, --gid_show shows gid address only
Table 24 - osmtest Flags and Options
Flag Description