User Manual
Table Of Contents
- Mellanox WinOF VPI User Manual
- Table of Contents
- List of Tables
- Document Revision History
- About this Manual
- 1 Introduction
- 2 Firmware Upgrade
- 3 Driver Features
- 3.1 Hyper-V with VMQ
- 3.2 Header Data Split
- 3.3 Receive Side Scaling (RSS)
- 3.4 Port Configuration
- 3.5 Load Balancing, Fail-Over (LBFO) and VLAN
- 3.6 Ports TX Arbitration
- 3.7 RDMA over Converged Ethernet (RoCE)
- 3.8 Network Virtualization using Generic Routing Encapsulation
- 3.9 Differentiated Services Code Point (DSCP)
- 4 Deploying Windows Server 2012 and Above with SMB Direct
- 5 Driver Configuration
- 6 Performance Tuning
- 7 OpenSM - Subnet Manager
- 8 InfiniBand Fabric
- 8.1 Network Direct Interface
- 8.2 part_man - Virtual IPoIB Port Creation Utility
- 8.3 InfiniBand Fabric Diagnostic Utilities
- 8.3.1 Utilities Usage
- 8.3.2 ibdiagnet
- 8.3.3 ibportstate
- 8.3.4 ibroute
- 8.3.5 ibdump
- 8.3.6 smpquery
- 8.3.7 perfquery
- 8.3.8 ibping
- 8.3.9 ibnetdiscover
- 8.3.10 ibtracert
- 8.3.11 sminfo
- 8.3.12 ibclearerrors
- 8.3.13 ibstat
- 8.3.14 vstat
- 8.3.15 osmtest
- 8.3.16 ibaddr
- 8.3.17 ibcacheedit
- 8.3.18 iblinkinfo
- 8.3.19 ibqueryerrors
- 8.3.20 ibsysstat
- 8.3.21 saquery
- 8.3.22 smpdump
- 8.4 InfiniBand Fabric Performance Utilities
- 8.4.1 ib_read_bw
- 8.4.2 ib_read_lat
- 8.4.3 ib_send_bw
- 8.4.4 ib_send_lat
- 8.4.5 ib_write_bw
- 8.4.6 ib_write_lat
- 8.4.7 ibv_read_bw
- 8.4.8 ibv_read_lat
- 8.4.9 ibv_send_bw
- 8.4.10 ibv_send_lat
- 8.4.11 ibv_write_bw
- 8.4.12 ibv_write_lat
- 8.4.13 nd_write_bw
- 8.4.14 nd_write_lat
- 8.4.15 nd_read_bw
- 8.4.16 nd_read_lat
- 8.4.17 nd_send_bw
- 8.4.18 nd_send_lat
- 8.4.19 NTttcp
- 9 Software Development Kit
- 10 Troubleshooting
- 11 Documentation
- Appendix A: Windows MPI (MS-MPI)
- Appendix B: NVGRE Configuration Scrips Examples
Rev 4.60
Mellanox Technologies
55
6.4.1 Supported Standard Performance Counters
6.4.1.1 Proprietary Mellanox Adapter Traffic Counters
Proprietary Mellanox adapter traffic counter set consists of global traffic statistics which gather
information from ConnectX®-3 and ConnectX®-3 Pro network adapters, and includes traffic
statistics, and various types of error and indications from both the Physical Function and Virtual
Function.
Table 7 - Mellanox Adapter Traffic Counters
Mellanox Adapter Traffic Counters Description
Bytes IN
Bytes Received Shows the number of bytes received by ConnectX-3 and ConnectX-3Pro
network adapter. The counted bytes include framing characters.
Bytes Received/Sec Shows the rate at which bytes are received by ConnectX-3 and Con-
nectX-3Pro network adapter. The counted bytes include framing charac-
ters.
Packets Received Shows the number of packets received by ConnectX-3 and ConnectX-
3Pro network interface.
Packets Received/Sec Shows the rate at which packets are received by ConnectX-3 and Con-
nectX-3Pro network interface.
Bytes/ Packets OUT
Bytes Sent Shows the number of bytes sent by ConnectX-3 and ConnectX-3Pro net-
work adapter. The counted bytes include framing characters.
Bytes Sent/Sec Shows the rate at which bytes are sent by ConnectX-3 and ConnectX-
3Pro network adapter. The counted bytes include framing characters.
Packets Sent Shows the number of packets sent by ConnectX-3 and ConnectX-3Pro
network interface.
Packets Sent/Sec Shows the rate at which packets are sent by ConnectX-3 and ConnectX-
3Pro network interface.
Bytes’ TOTAL
Bytes Total Shows the total of bytes handled by ConnectX-3 and ConnectX-3Pro net-
work adapter. The counted bytes include framing characters.
Bytes Total/Sec Shows the total rate of bytes that are sent and received by ConnectX-3and
ConnectX-3Pro network adapter. The counted bytes include framing
characters.
Packets Total Shows the total of packets handled by ConnectX-3 and ConnectX-3Pro
network interface.
Packets Total/Sec Shows the rate at which packets are sent and received by ConnectX-3 and
ConnectX-3Pro network interface.
Control Packets The total number of successfully received control frames