User Manual
Table Of Contents
- Mellanox WinOF VPI User Manual
- Table of Contents
- List of Tables
- Document Revision History
- About this Manual
- 1 Introduction
- 2 Firmware Upgrade
- 3 Driver Features
- 3.1 Hyper-V with VMQ
- 3.2 Header Data Split
- 3.3 Receive Side Scaling (RSS)
- 3.4 Port Configuration
- 3.5 Load Balancing, Fail-Over (LBFO) and VLAN
- 3.6 Ports TX Arbitration
- 3.7 RDMA over Converged Ethernet (RoCE)
- 3.8 Network Virtualization using Generic Routing Encapsulation
- 3.9 Differentiated Services Code Point (DSCP)
- 4 Deploying Windows Server 2012 and Above with SMB Direct
- 5 Driver Configuration
- 6 Performance Tuning
- 7 OpenSM - Subnet Manager
- 8 InfiniBand Fabric
- 8.1 Network Direct Interface
- 8.2 part_man - Virtual IPoIB Port Creation Utility
- 8.3 InfiniBand Fabric Diagnostic Utilities
- 8.3.1 Utilities Usage
- 8.3.2 ibdiagnet
- 8.3.3 ibportstate
- 8.3.4 ibroute
- 8.3.5 ibdump
- 8.3.6 smpquery
- 8.3.7 perfquery
- 8.3.8 ibping
- 8.3.9 ibnetdiscover
- 8.3.10 ibtracert
- 8.3.11 sminfo
- 8.3.12 ibclearerrors
- 8.3.13 ibstat
- 8.3.14 vstat
- 8.3.15 osmtest
- 8.3.16 ibaddr
- 8.3.17 ibcacheedit
- 8.3.18 iblinkinfo
- 8.3.19 ibqueryerrors
- 8.3.20 ibsysstat
- 8.3.21 saquery
- 8.3.22 smpdump
- 8.4 InfiniBand Fabric Performance Utilities
- 8.4.1 ib_read_bw
- 8.4.2 ib_read_lat
- 8.4.3 ib_send_bw
- 8.4.4 ib_send_lat
- 8.4.5 ib_write_bw
- 8.4.6 ib_write_lat
- 8.4.7 ibv_read_bw
- 8.4.8 ibv_read_lat
- 8.4.9 ibv_send_bw
- 8.4.10 ibv_send_lat
- 8.4.11 ibv_write_bw
- 8.4.12 ibv_write_lat
- 8.4.13 nd_write_bw
- 8.4.14 nd_write_lat
- 8.4.15 nd_read_bw
- 8.4.16 nd_read_lat
- 8.4.17 nd_send_bw
- 8.4.18 nd_send_lat
- 8.4.19 NTttcp
- 9 Software Development Kit
- 10 Troubleshooting
- 11 Documentation
- Appendix A: Windows MPI (MS-MPI)
- Appendix B: NVGRE Configuration Scrips Examples
Rev 4.60
Mellanox Technologies
37
3.9.6 DSCP Sanity Testing
To verify that all QoS and DSCP settings were correct, you can capture incoming and outgoing
traffic by using the ibdump tool and see the DSCP value in the captured packets as displayed in
the figure below.
RroceDscpMarkPriorityFlowControl_1 1
RroceDscpMarkPriorityFlowControl_2 2
RroceDscpMarkPriorityFlowControl_3 3
RroceDscpMarkPriorityFlowControl_4 4
RroceDscpMarkPriorityFlowControl_5 5
RroceDscpMarkPriorityFlowControl_6 6
RroceDscpMarkPriorityFlowControl_7 7
Table 6 - DSCP Default Registry Keys Settings
Registry Key Default Value