User Manual
Table Of Contents
- Mellanox WinOF VPI User Manual
- Table of Contents
- List of Tables
- Document Revision History
- About this Manual
- 1 Introduction
- 2 Firmware Upgrade
- 3 Driver Features
- 3.1 Hyper-V with VMQ
- 3.2 Header Data Split
- 3.3 Receive Side Scaling (RSS)
- 3.4 Port Configuration
- 3.5 Load Balancing, Fail-Over (LBFO) and VLAN
- 3.6 Ports TX Arbitration
- 3.7 RDMA over Converged Ethernet (RoCE)
- 3.8 Network Virtualization using Generic Routing Encapsulation
- 3.9 Differentiated Services Code Point (DSCP)
- 4 Deploying Windows Server 2012 and Above with SMB Direct
- 5 Driver Configuration
- 6 Performance Tuning
- 7 OpenSM - Subnet Manager
- 8 InfiniBand Fabric
- 8.1 Network Direct Interface
- 8.2 part_man - Virtual IPoIB Port Creation Utility
- 8.3 InfiniBand Fabric Diagnostic Utilities
- 8.3.1 Utilities Usage
- 8.3.2 ibdiagnet
- 8.3.3 ibportstate
- 8.3.4 ibroute
- 8.3.5 ibdump
- 8.3.6 smpquery
- 8.3.7 perfquery
- 8.3.8 ibping
- 8.3.9 ibnetdiscover
- 8.3.10 ibtracert
- 8.3.11 sminfo
- 8.3.12 ibclearerrors
- 8.3.13 ibstat
- 8.3.14 vstat
- 8.3.15 osmtest
- 8.3.16 ibaddr
- 8.3.17 ibcacheedit
- 8.3.18 iblinkinfo
- 8.3.19 ibqueryerrors
- 8.3.20 ibsysstat
- 8.3.21 saquery
- 8.3.22 smpdump
- 8.4 InfiniBand Fabric Performance Utilities
- 8.4.1 ib_read_bw
- 8.4.2 ib_read_lat
- 8.4.3 ib_send_bw
- 8.4.4 ib_send_lat
- 8.4.5 ib_write_bw
- 8.4.6 ib_write_lat
- 8.4.7 ibv_read_bw
- 8.4.8 ibv_read_lat
- 8.4.9 ibv_send_bw
- 8.4.10 ibv_send_lat
- 8.4.11 ibv_write_bw
- 8.4.12 ibv_write_lat
- 8.4.13 nd_write_bw
- 8.4.14 nd_write_lat
- 8.4.15 nd_read_bw
- 8.4.16 nd_read_lat
- 8.4.17 nd_send_bw
- 8.4.18 nd_send_lat
- 8.4.19 NTttcp
- 9 Software Development Kit
- 10 Troubleshooting
- 11 Documentation
- Appendix A: Windows MPI (MS-MPI)
- Appendix B: NVGRE Configuration Scrips Examples
Rev 4.60
Mellanox Technologies
22
Step 2. Right-click a Mellanox ConnectX 10Gb Ethernet adapter (under “Network adapters” list) and
left click Properties. Select the LBFO tab from the Properties window.
The LBFO dialog enables creating, modifying or removing a bundle.
To create a new bundle, perform the following
Step 1. Click Create.
Step 2. Enter a (unique) bundle name.
Step 3. Select a bundle type.
Step 4. Select the adapters to be included in the bundle (that have not been associated with a VLAN).
Step 5. [Optional] Select Primary Adapter.
An active-passive scenario used for data transfer of link disconnecting. In such scenario, the
system uses one of the other interfaces. When the primary link comes up, the LBFO interface
returns to transfer data using the primary interface. If the primary adapter is not selected, the
primary interface is selected randomly.
Step 6. [Optional] Failback to Primary
It is not recommended to open the Properties window of more than one adapter simulta-
neously.
Only Mellanox Technologies adapters can be part of the LBFO.