Specifications
Table Of Contents
- Safety information
- Chapter 1
- Product introduction
- Chapter 2
- BIOS information
- 2.1 Managing and updating your BIOS
- 2.2 BIOS setup program
- 2.3 Main menu
- 2.4 Ai Tweaker menu
- 2.4.1 CPU bus speed : DRAM speed ratio mode [Auto]
- 2.4.2 Memory Frequency [Auto]
- 2.4.3 EPU Power Saving Mode [Disabled]
- 2.4.4 GPU Boost [OK]
- 2.4.5 DRAM Timing Control
- 2.4.6 CPU Power Management
- 2.4.7 Offset Mode Sign [+]
- 2.4.8 DRAM Voltage [Auto]
- 2.4.9 VCCIO Voltage [Auto]
- 2.4.10 VCCSA Voltage [Auto]
- 2.4.11 CPU PLL Voltage [Auto]
- 2.4.12 PCH Voltage [Auto]
- 2.4.13 Load-Line Calibration [Auto]
- 2.5 Advanced menu
- 2.6 Monitor menu
- 2.7 Boot menu
- 2.7.1 Bootup NumLock State [On]
- 2.7.2 Full Screen Logo [Enabled]
- 2.7.3 Wait for ‘F1’ If Error [Enabled]
- 2.7.4 Option ROM Messages [Force BIOS]
- 2.7.5 Setup Mode [EZ Mode]
- 2.7.6 UEFI/Legacy Boot [Enabled both UEFI and Legacy]
- 2.7.7 PCI ROM Priority [Legacy ROM]
- 2.7.8 Boot Option Priorities
- 2.7.9 Boot Override
- 2.8 Tools menu
- 2.9 Exit menu
- Appendices

2-22 ASUS P8B75-M
2.6 Monitor menu
The Monitor menu displays the system temperature/power status, and allows you to change
the fan settings.
Scroll down to display the following items:
Main
Ai Tweaker
Advanced Monitor Boot Tool
Exit
Version 2.10.1208. Copyright (C) 2012 American Megatrends, Inc.
→←: Select Screen
↑↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Shortcut
F5: Optimized Defaults
F10: Save ESC: Exit
F12: Print Screen
EFI BIOS Utility - Advanced Mode
CPU Temperature +45ºC / +113ºF
MB Temperature +34ºC / +93ºF
CPU Fan Speed 3325 RPM
Chassis Fan 1 Speed N/A
Chassis Fan 2 Speed N/A
CPU Q-Fan Control Enabled
CPU Fan Speed Low Limit 200 RPM
CPU Fan Prole Standard
Chassis Q-Fan Control Enabled
Chassis Fan Speed Low Limit 600 RPM
Chassis Fan Prole Standard
CPU Voltage +1.184 V
3.3V Voltage +3.312 V
5V Voltage +5.080 V
Version 2.10.1208. Copyright (C) 2012 American Megatrends, Inc.
12V Voltage +12.192 V
Anti Surge Support Enabled
2.5.11 Network Stack
Network Stack [Disable Link]
This item allows user to disable or enable the UEFI network stack. Conguration options:
[Disable Link] [Enable]
Ipv4 PXE Support [Enabled]
This item appears only when you set the Network Stack item to [Enabled]. When this item is
disabled, the IPV4 PXE boot option will not be created. Conguration options: [Disable Link]
[Enabled]
Ipv6 PXE Support [Enabled]
This item appears only when you set the Network Stack item to [Enabled]. When this item is
disabled, the IPV6 PXE boot option will not be created. Conguration options: [Disable Link]
[Enabled]










