Manual
Table Of Contents
- P7P55D-E Premium specifications summary
- About this guide
- Safety information
- Notices
- Chapter 1: Product introduction
- Chapter 2: Hardware information
- Chapter 3: BIOS setup
- 3.1 Knowing BIOS
- 3.2 Updating BIOS
- 3.3 BIOS setup program
- 3.4 Main menu
- 3.5 Ai Tweaker menu
- 3.5.1 Ai Overclock Tuner [Auto]
- 3.5.2 CPU Ratio Setting [Auto]
- 3.5.3 Intel(R) SpeedStep(TM) Tech [Enabled]
- 3.5.4 Intel(R) TurboMode Tech [Enabled]
- 3.5.5 Xtreme Phase Full Power Mode [Auto]
- 3.5.6 DRAM Frequency [Auto]
- 3.5.7 QPI Frequency [Auto]
- 3.5.8. DRAM Timing Control [Auto]
- 3.5.9 CPU Differential Amplitude [Auto]
- 3.5.10 CPU Clock Skew [Auto]
- 3.5.11 CPU Voltage Mode [Offset]
- 3.5.12 IMC Voltage [Auto]
- 3.5.13 DRAM Voltage [Auto]
- 3.5.14 CPU PLL Voltage [Auto]
- 3.5.15 PCH Voltage [Auto]
- 3.5.16 DRAM DATA REF Voltage on CHA/B [Auto]
- 3.5.17 DRAM CTRL REF Voltage on CHA/B [Auto]
- 3.5.18 Load-Line Calibration [Auto]
- 3.5.19 CPU Spread Spectrum [Auto]
- 3.5.20 PCIE Spread Spectrum [Auto]
- 3.6 Advanced menu
- 3.7 Power menu
- 3.8 Boot menu
- 3.9 Tools menu
- 3.10 Exit menu
- Chapter 4: Software support
- Chapter 5: Multiple GPU technology support
ASUS P7P55D-E Premium 3-33
Chapter 3
3.8.2 Boot Settings Conguration
Quick Boot [Enabled]
[Disabled] When set to [Disabled], BIOS performs all the POST items.
[Enabled] When set to [Enabled], BIOS skips some power on self tests (POST) while
booting to decrease the time needed to boot the system.
Full Screen Logo [Enabled]
[Disabled] Disables the full screen logo display feature.
[Enabled] Enables the full screen logo display feature.
Set this item to [Enabled] to use the ASUS MyLogo 2™ feature.
AddOn ROM Display Mode [Force BIOS]
[Force BIOS] The third-party ROM messages will be forced to display during the boot
sequence.
[Keep Current] The third-party ROM messages will be displayed only if the third-party
manufacturer had set the add-on device to do so.
Bootup Num-Lock [On]
[Off] Sets the power-on state of the NumLock to [Off].
[On] Sets the power-on state of the NumLock to [On].
Wait For ‘F1’ If Error [Enabled]
[Disabled] Disables this function.
[Enabled] The system waits for the <F1> key to be pressed when error occurs.
Hit ‘DEL’ Message Display [Enabled]
[Disabled] Disables this function.
[Enabled] The system displays the message “Press DEL to run Setup” during POST.
POST State LEDs [Enabled]
[Enabled] Turn on onboard device LEDs in the order of the device POST sequence.
[Disabled] Disables this function.
Boot Settings Conguration
Quick Boot [Enabled]
Full Screen Logo [Enabled]
AddOn ROM Display Mode [Force BIOS]
Bootup Num-Lock [On]
Wait For ‘F1’ If Error [Enabled]
Hit ‘DEL’ Message Display [Enabled]
POST State LEDs [Enabled]
BIOS SETUP UTILITY
Boot
Allows BIOS to skip
certain tests while
booting. This will
decrease the time
needed to boot the
system.