Manual
Table Of Contents
- P7P55D-E Premium specifications summary
- About this guide
- Safety information
- Notices
- Chapter 1: Product introduction
- Chapter 2: Hardware information
- Chapter 3: BIOS setup
- 3.1 Knowing BIOS
- 3.2 Updating BIOS
- 3.3 BIOS setup program
- 3.4 Main menu
- 3.5 Ai Tweaker menu
- 3.5.1 Ai Overclock Tuner [Auto]
- 3.5.2 CPU Ratio Setting [Auto]
- 3.5.3 Intel(R) SpeedStep(TM) Tech [Enabled]
- 3.5.4 Intel(R) TurboMode Tech [Enabled]
- 3.5.5 Xtreme Phase Full Power Mode [Auto]
- 3.5.6 DRAM Frequency [Auto]
- 3.5.7 QPI Frequency [Auto]
- 3.5.8. DRAM Timing Control [Auto]
- 3.5.9 CPU Differential Amplitude [Auto]
- 3.5.10 CPU Clock Skew [Auto]
- 3.5.11 CPU Voltage Mode [Offset]
- 3.5.12 IMC Voltage [Auto]
- 3.5.13 DRAM Voltage [Auto]
- 3.5.14 CPU PLL Voltage [Auto]
- 3.5.15 PCH Voltage [Auto]
- 3.5.16 DRAM DATA REF Voltage on CHA/B [Auto]
- 3.5.17 DRAM CTRL REF Voltage on CHA/B [Auto]
- 3.5.18 Load-Line Calibration [Auto]
- 3.5.19 CPU Spread Spectrum [Auto]
- 3.5.20 PCIE Spread Spectrum [Auto]
- 3.6 Advanced menu
- 3.7 Power menu
- 3.8 Boot menu
- 3.9 Tools menu
- 3.10 Exit menu
- Chapter 4: Software support
- Chapter 5: Multiple GPU technology support

ASUS P7P55D-E Premium 4-17
Chapter 4
Deleting a RAID set
Take caution when deleting a RAID set. You will lose all data on the hard disk drives when
you delete a RAID set.
To delete a RAID set
1. From the utility main menu, select 2. Delete RAID Volume and press <Enter>. The
following screen appears.
Intel(R) Matrix Storage Manager option ROM v8.9.0.1014 PCH-D wRAID5
Copyright(C) 2003-09 Intel Corporation. All Rights Reserved.
[ DELETE VOLUME MENU ]
[ HELP ]
Deleting a volume will reset the disks to non-RAID.
WARNING: ALL DISK DATA WILL BE DELETED.
(This does not apply to Recovery volumes)
[↑↓]-Select [ESC]-Previous Menu [DEL]-Delete Volume
Name Level Drives Capacity Status Bootable
Volume0 RAID0(Stripe) 2 298.0GB Normal Yes
Exiting the Intel
®
Matrix Storage Manager
To exit the utility
1. From the utility main menu, select 5. Exit, and then press <Enter>. The following
warning message appears.
2. Press <Y> to exit or press <N> to return to the utility main menu.
Are you sure you want to exit? (Y/N):
[ CONFIRM EXIT ]
2. Use the up/down arrow key to select the RAID set you want to delete, and then press
<Del>. The following warning message appears.
3. Press <Y> to delete the RAID set and return to the utility main menu, or press <N> to
return to the DELETE VOLUME menu.
ALL DATA IN THE VOLUME WILL BE LOST!
(This does not apply to Recovery volumes)
Are you sure you want to delete volume “Volume0”? (Y/N):
[ DELETE VOLUME VERIFICATION ]