® P5S-VM Super7 microATX Motherboard USER’S MANUAL
USER'S NOTICE No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. (“ASUS”).
ASUS CONTACT INFORMATION ASUSTeK COMPUTER INC. (Asia-Pacific) Marketing Address: Telephone: Fax: Email: 150 Li-Te Road, Peitou, Taipei, Taiwan 112 +886-2-2894-3447 +886-2-2894-3449 info@asus.com.tw Technical Support Tel (English): Tel (Chinese): Fax: Email: Newsgroup: WWW: FTP: +886-2-2894-3447 ext. 706 +886-2-2894-3447 ext. 111 +886-2-2895-9254 tsd@asus.com.tw news2.asus.com.tw www.asus.com.tw ftp.asus.com.
CONTENTS I. INTRODUCTION ........................................................................... 7 How this Manual is Organized ........................................................ 7 Item Checklist .................................................................................. 7 II. FEATURES .................................................................................... 8 ASUS P5S-VM Motherboard ..........................................................
CONTENTS Load BIOS Defaults ................................................................... Load Setup Defaults ................................................................... Supervisor Password and User Password .................................. IDE HDD Auto Detection .......................................................... Save & Exit Setup ...................................................................... Exit Without Saving ................................................................
FCC & DOC COMPLIANCE Federal Communications Commission Statement This device complies with FCC Rules Part 15. Operation is subject to the following two conditions: • • This device may not cause harmful interference, and This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
I. INTRODUCTION I. Introduction II. Features III. Installation IV. BIOS Setup V. Software Setup VI. Software Reference VII. Appendix I.
II. FEATURES ASUS P5S-VM Motherboard The ASUS P5S-VM is carefully designed for the demanding PC user who wants advanced features in a small package. II. FEA TURES Features Specifications • SiS AGPset: SiS (Silicon Integrated Systems Corp.) 530 AGPset with support for a 100MHz Front Side Bus (FSB), all current Socket 7 processors and with integrated Super AGP 2D/ 3D VGA controller for high performance hardware 2D/3D VGA acceleration.
II. FEATURES II. FEA TURES Smart Series Special Features • Enhanced ACPI and Anti-Boot Virus BIOS: Features a programmable BIOS, offering enhanced ACPI for Windows 98 compatibility, built-in firmware-based virus protection through Trend ChipAway Virus codes, and autodetection of most devices for virtually automatic setup. • Desktop Management Interface (DMI): Supports DMI through BIOS, which allows hardware to communicate within a standard protocol creating a higher level of compatibility.
II. FEATURES II. FEA TURES Smart Series • Auto Fan Off: The system fans will power off automatically even in sleep mode. This function reduces both energy consumption and system noise, and is an important feature in implementing silent PC systems.
II. FEATURES Parts of the ASUS P5S-VM Motherboard (T): Top (B): Bottom ATX 3 DIMM Power Sockets CPU ZIF Socket 7 ISA Slot Programmable Flash ROM SiS AGPset with Heatsink (not shown) L2 Cache Tag RAM 8MB VGA Memory (optional) PS/2 Mouse (T) PS/2 Keyboard (B) II.
III.
III. HARDWARE SETUP Motherboard Settings 1) 2) 3) 4) 5) 6) 7) 8) VIRQ VEN_DIS LINEOUT_SW AUDIOEN KB_UP FS0, FS1, FS2, FS3 BF0, BF1, BF2 VID0, VID1, VID2, VID3 p. 14 p. 14 p. 15 p. 15 p. 15 p. 16 p. 16 p.
III. HARDWARE SETUP Hardware Setup Steps 1. 2. 3. 4. 5. 6. Check Motherboard Settings Install Memory Modules Install the Central Processing Unit (CPU) Install Expansion Cards Connect Ribbon Cables, Cabinet Wires, and Power Supply Setup the BIOS Software 1. Motherboard Settings This section explains how to change your motherboard’s function settings through the use of switches and/or jumpers. III.
III. HARDWARE SETUP 3. Audio Line Out Setting (LINEOUT_SW) / 4. Audio Setting (AUDIOEN) LINEOUT_SW allows you to set the audio line out settings. The default allows a stereo amplified connection to external speakers through the Line Out jack of the optional GAME/AUDIO connector. Sound quality is better using the Without amplifier setting and an external amplifier or powered speakers. AUDIOEN allows you to enable or disable the onboard audio.
III. HARDWARE SETUP 6. CPU External (BUS) Frequency Selection (FS0, FS1, FS2, FS3) These jumpers tell the clock generator what frequency to send to the CPU, chipset, and AGP. These allow the selection of the CPU’s External frequency (or BUS Clock). The BUS Clock times the BUS Ratio equals the CPU's Internal frequency (the advertised CPU speed). 7.
III. HARDWARE SETUP CPU Model Freq. Mult. BUS F. (BUS Freq.) FS3 FS2 FS1 FS0 (Freq. Mult.) BF2 BF1 BF0 AMD-K6-III/450 AMD-K6-III/400 450MHz 400MHz A-4.5x 100MHz A-4.0x 100MHz [1-2] [2-3] [2-3] [1-2] [1-2] [2-3] [2-3] [1-2] [2-3] [2-3] [2-3] [2-3] [1-2] [2-3] AMD-K6-2/475 AMD-K6-2/450 AMD-K6-2/400 475MHz 450MHz 400MHz A-5.0x 95MHz A-4.5x 100MHz A-4.
III. HARDWARE SETUP Compatible Cyrix CPU Identification The only Cyrix 6x86-PR166+ CPU that is supported on this motherboard must be Revision 2.7 or later. Look on the underside of the CPU for the serial number. The number should read G8DC6620A or later. 8. Voltage Regulator Output Selection (VID0, VID1, VID2, VID3) These jumpers set the VCORE voltage supplied to the CPU. Switching regulators allow some jumper settings to be the same for two voltages of different power planes. III.
VID0 VID1 VID2 VID3 VID0 VID1 VID2 VID3 VID0 VID1 VID2 VID3 VID0 VID1 VID2 VID3 VID0 VID1 VID2 VID3 III. HARDWARE SETUP 2.0Volts 2.1Volts 2.2Volts 2.3Volts 2.4Volts 2.8Volts 2.9Volts 3.0Volts 3.1Volts 3.2Volts 3.3Volts 3.4olts 3.5Volts 3 2 1 01 3 2 1 3 2 1 III.
III. HARDWARE SETUP 2. System Memory (DIMM) This motherboard uses only Dual Inline Memory Modules (DIMMs). Sockets are available for 3.3Volt (power level) unbuffered Synchronous Dynamic Random Access Memory (SDRAM) of either 8, 16, 32, 64, 128MB, or 256MB to form a memory size between 8MB and 768MB. One side (with memory chips) of the DIMM takes up one row on the motherboard.
III. HARDWARE SETUP DIMM Memory Installation Procedures: Insert the module(s) as shown. Because the number of pins are different on either side of the breaks, the module will only fit in the orientation as shown. DRAM SIMM modules have the same pin contacts on both sides. SDRAM DIMMs have different pin contacts on each side and therefore have a higher pin density. Lock III. H/W SETUP System Memory 01 20 Pins 60 Pins 88 Pins P5S-VM 168-Pin DIMM Sockets The DIMMs must be 3.3Volt unbuffered SDRAMs.
III. HARDWARE SETUP 3. Central Processing Unit (CPU) The motherboard provides a 321-pin ZIF Socket 7 that is backwards compatible with ZIF Socket 5 processors. The CPU that came with the motherboard should have a fan attached to it to prevent overheating. If this is not the case then purchase a fan before you turn on your system. WARNING! Without a fan circulating air on the CPU, the CPU can overheat and cause damage to both the CPU and the motherboard. III.
III. HARDWARE SETUP 4. Expansion Cards WARNING! Make sure that you unplug your power supply when adding or removing expansion cards or other system components. Failure to do so may cause severe damage to both your motherboard and expansion cards. Expansion Card Installation Procedure: III. H/W SETUP Expansion Cards 1. Read your expansion card documentation on any hardware and software settings that may be required to setup your specific card. 2. Set any necessary jumpers on your expansion card. 3.
III. HARDWARE SETUP To simplify this process, this motherboard complies with the Plug and Play (PNP) specification which was developed to allow automatic system configuration whenever a PNP-compliant card is added to the system. For PNP cards, IRQs are assigned automatically from those available. If the system has both Legacy and PNP ISA cards installed, IRQs are assigned to PNP cards from those not used by Legacy cards.
III. HARDWARE SETUP 5. External Connectors WARNING! Some pins are used for connectors or power sources. These are clearly separated from jumpers in the Motherboard Layout. Placing jumper caps over these will cause damage to your motherboard. IMPORTANT: Ribbon cables should always be connected with the red stripe to Pin 1 on the connectors. Pin 1 is usually on the side closest to the power connector on hard drives and CD-ROM drives, but may be on the opposite side on floppy disk drives.
III. HARDWARE SETUP 3. Parallel Port Connector (25-pin Female) You can enable the parallel port and choose the IRQ through “Onboard Parallel Port” in Chipset Features Setup of the BIOS SOFTWARE. NOTE: Serial printers must be connected to the serial port. Parallel (Printer) Port (25-pin Female) III. H/W SETUP Connectors 4. Serial Port COM1 (9-pin Male) / 5. COM2 Connectors (10-1 pin Male) The two serial ports can be used for pointing devices or other serial devices.
III. HARDWARE SETUP 6. Monitor (VGA) Output Connector (15-pin Female) This connector is for output to a VGA-compatible device. VGA Monitor (15-pin Female) III. H/W SETUP Connectors 7. Floppy drive connector (FLOPPY, 34-1 pin block ) This connector supports the provided floppy drive ribbon cable. After connecting the single end to the board, connect the two plugs on the other end to the floppy drives.
III. HARDWARE SETUP 9. Joystick/Midi Connector (15-pin Female) (with optional onboard audio) You may connect game joysticks or game pads to this connector for playing games. Connect Midi devices for playing or editing audio. Joystick/Midi (15-pin Female) 10. Universal Serial BUS Ports 1 & 2 (Two 4-pin Female Sockets) Two USB ports are available for connecting USB devices. III.
III. HARDWARE SETUP 11. Primary / Secondary IDE connectors (Two 40-1 pin block) These connectors support the provided IDE hard disk ribbon cable. After connecting the single end to the board, connect the two plugs at the other end to your hard disk(s). If you install two hard disks on the same channel, you must set the second drive to Slave mode. Refer to the documentation of your hard disk for the jumper settings.
III. HARDWARE SETUP 12. ATX Power Supply Connector (ATX, 20-pin block) This connector connects to an ATX power supply. The plug from the power supply will only insert in one orientation because of the different hole sizes. Find the proper orientation and push down firmly making sure that the pins are aligned. IMPORTANT: Make sure that your ATX power supply can supply at least 10mAmp on the 5-volt standby lead (+5VSB).
III. HARDWARE SETUP 14. ATX Power Switch/Soft Power Switch Lead (PWR, 2 pins) The system power can be controlled by a momentary switch connected to this lead. Pushing the button once will switch the system between ON and SLEEP. Pushing the switch while in the ON mode for more than 4 seconds will turn the system off. The system power LED shows the status of the system’s power. 15. IDE Activity LED Lead (IDELED, 2 pins) This connector supplies power to the cabinet’s IDE activity LED.
III. HARDWARE SETUP 21. Wake-on-LAN Activity Connector (3-pin WOLCON) The WOLCON connector allows the system to power up when there is a wakeup packet or signal is received from the network through the ASUS PCI-L101 LAN card (see ASUS LAN CARD). IMPORTANT: This feature requires that the WAKE On LAN Power Up Control is set to Enabled (see Power Management Setup under BIOS SOFTWARE) and that your system has an ATX power supply with at least 720mA +5V standby power.
III. HARDWARE SETUP 24. CPU/Chassis Cooling Fan Connectors (FAN, 3 pins) These connectors support 3-pin cooling fans of 500mA (6W) or less with a minimum of 3,500RPM. Orientate the fans so that the heatsink fins allow airflow to go across the onboard heatsink(s) instead of the expansion slots. Depending on the fan manufacturer, the wiring and plug may be different. The red wire should be positive, while the black should be ground.
III. HARDWARE SETUP (This page was intentionally left blank.
III. HARDWARE SETUP Power Connection Procedures 1. After all jumpers and connections are made, close the system case cover. 2. Be sure that all switches are off (in some systems, marked with ). 3. Connect the power supply cord into the power supply located on the back of your system case according to your system user’s manual. 4. Connect the power cord into a power outlet that is equipped with a surge protector. III. H/W SETUP Power Connections 5.
IV. BIOS SETUP Flash Memory Writer Utility AFLASH.EXE: This is the Flash Memory Writer utility that updates the BIOS by uploading a new BIOS file to the programmable flash ROM chip on the motherboard. To determine the BIOS version of your motherboard, check the last four numbers of the code displayed on the upper left-hand corner of your screen during bootup. Larger numbers represent a newer BIOS file. This file works only in DOS mode.
IV. BIOS SETUP 2. Update BIOS Including Boot Block and ESCD This option updates the boot block, the baseboard BIOS, and the ACPI extended system configuration data (ESCD) parameter block from a new BIOS file. See the next page for procedures on downloading an updated BIOS file. To update your current BIOS, type [2] at the Main Menu and then press . The Update BIOS Including Boot Block and ESCD screen appears. Type the filename of your new BIOS and the path and then press . IV.
IV. BIOS SETUP Managing and Updating Your Motherboard’s BIOS Upon First Use of the Computer System 1. Create a bootable system floppy disk by typing [FORMAT A:/S] from the DOS prompt without creating “AUTOEXEC.BAT” and “CONFIG.SYS” files. 2. Copy AFLASH.EXE to the just created boot disk. 3. Run AFLASH.EXE from this new disk and select option 1. Save Current BIOS to File. See 1. Save Current BIOS To File on the previous page for more details and the rest of the steps.
IV. BIOS SETUP 6. BIOS Setup The motherboard supports 5-volt programmable 2-Mbit Flash ROM chips. These memory chips can be updated when BIOS upgrades are released. Use the Flash Memory Writer utility to download the new BIOS file into the ROM chip as described in detail in this section. All computer motherboards provide a Setup utility program for specifying the system configuration and settings. If your motherboard came in a computer system, the proper configuration entries may have already been made.
IV. BIOS SETUP Load Defaults Load BIOS Defaults loads the minimum settings for troubleshooting. Load Setup Defaults, on the other hand, is for loading optimized defaults for regular use. Choosing defaults at this level will modify all applicable settings. A section at the bottom of the preceding screen displays the control keys for this screen. Take note of these keys and their respective uses.
IV. BIOS SETUP Time To set the time, highlight the “Time” field and then press either / or <+>/<–> to set the current time. Follow the hour, minute and second format. Valid values for hour, minute and second are: (Hour: (00 to 23), Minute: (00 to 59), Second: (00 to 59). If you do not want to modify the current time, press three times to go to HARD DISKS. NOTE: You can bypass the date and time prompts by creating an AUTOEXEC.BAT file.
IV. BIOS SETUP Auto detection of hard disks on bootup For each field: Primary Master, Primary Slave, Secondary Master, and Secondary Slave, you can select Auto under the TYPE and MODE fields. This will enable auto detection of your IDE hard disk during bootup. This will allow you to change your hard disks (with the power off) and then power on without having to reconfigure your hard disk type.
IV. BIOS SETUP BIOS Features Setup BIOS Features Setup consists of configuration entries that allow you to improve your system performance, or let you set up some system features according to your preference. Some entries are required by the motherboard’s design to remain in their default settings. IV. BIOS SETUP BIOS Features A section at the lower right of the screen displays the control keys you can use. Take note of these keys and their respective uses.
IV. BIOS SETUP Quick Power On Self Test (Enabled) This field speeds up the Power-On Self Test (POST) routine by skipping retesting a second, third, and forth time. Setup default setting for this field is Enabled. A complete test of the system is done on each test. HDD Sequence SCSI/IDE First (IDE) When using both SCSI and IDE hard disk drives, IDE is always the boot disk using drive letter C (default setting of IDE). This new feature allows a SCSI hard disk drive to be the boot disk when set to SCSI.
IV. BIOS SETUP IV. BIOS SETUP BIOS Features C8000 - CBFFF Shadow to DC000 - DFFFF Shadow (Disabled) These fields are used for shadowing other expansion card ROMs. If you install other expansion cards with ROMs on them, you will need to know which addresses the ROMs use to shadow them specifically. Shadowing a ROM reduces the memory available between 640KB and 1024KB by the amount used for this purpose.
IV. BIOS SETUP Chipset Features Setup Chipset Features Setup controls the configuration of the board’s chipset. Control keys for this screen are the same as in the BIOS Features Setup screen. Chipset Features NOTE: SETUP Defaults are noted in parenthesis next to each function heading. Details of Chipset Features Setup IV. BIOS SETUP Chipset Features SDRAM Configuration (By SPD) This sets the optimal timing for items 2-4. Leave on default setting, depending on the memory modules that you are using.
IV. BIOS SETUP IV. BIOS SETUP Chipset Features Graphics Aperture Size (64MB) Memory-mapped, graphics data structures can reside in a Graphics Aperture. Leave on default setting. Memory Hole At Address (None) This allows you to specify the memory address space to be reserved for ISA expansion cards that specifically require this setting. Setting the address space to a particular setting (available settings: 15M-16M, 14M-16M, 12M-16M) will make that memory space unavailable to the system.
IV. BIOS SETUP IV. BIOS SETUP Chipset Features Parallel Port Mode (ECP+EPP) This field allows you to set the operation mode of the parallel port. The setting Normal, allows normal-speed operation but in one direction only; EPP allows bidirectional parallel port operation at maximum speed; ECP allows the parallel port to operate in bidirectional mode and at a speed faster than the maximum data transfer rate; ECP+EPP allows normal speed operation in a two-way mode.
IV. BIOS SETUP Power Management Setup Power Management Setup allows you to reduce power consumption. This feature turns off the video display and shuts down the hard disk after a period of inactivity. NOTE: SETUP Defaults are noted in parenthesis next to each function heading. Details of Power Management Setup IV. BIOS SETUP Power Management Power Management (User Define) This field acts as the master control for the power management modes.
IV. BIOS SETUP IV. BIOS SETUP Power Management Video Off Method (DPMS OFF) This field defines the video off features. These options are available: DPMS OFF, DPMS Reduce ON, Blank Screen, V/H SYNC+Blank, DPMS Standby, and DPMS Suspend. The DPMS (Display Power Management System) features allow the BIOS to control the video display card if it supports the DPMS feature. Blank Screen only blanks the screen (for monitors without power management or “green” features).
IV. BIOS SETUP ASUS P5S-VM User’s Manual IV. BIOS SETUP Power Management Power Management Wake On LAN (Enable) This allows you to remotely power up your system thorugh your network by sendng a wake-up frame or signal. With this feature, you can remotely upload/download data to/from systems during off-peak hours. Set to Enable to use this feature.
IV. BIOS SETUP PNP and PCI Setup This “PNP and PCI Setup” option configures the PCI bus slots. All PCI bus slots on the system use INTA#, thus all installed PCI cards must be set to this value. NOTE: SETUP Defaults are noted in parenthesis next to each function heading. Details of PNP and PCI Setup IV. BIOS SETUP Plug & Play/PCI PNP OS Installed (No) This field allows you to use a Plug-and-Play (PnP) operating system to configure the PCI bus slots instead of using the BIOS.
IV. BIOS SETUP DMA x Used By ISA (No/ICU) These fields indicate whether or not the displayed DMA channel for each field is being used by a legacy (non-PnP) ISA card. Available options include: No/ICU and Yes. The first option, the default setting, indicates either that the displayed DMA channel is not used or an ICU is being used to determine if an ISA card is using that channel.
IV. BIOS SETUP Load BIOS Defaults This “Load BIOS Defaults” option allows you to load the troubleshooting default values permanently stored in the BIOS ROM. These default settings are non-optimal and disable all high performance features. To load these default settings, highlight “Load BIOS Defaults” on the main screen and then press . The system displays a confirmation message on the screen. Press and then to confirm. Press and then to abort.
IV. BIOS SETUP Supervisor Password and User Password These two options set the system passwords. “Supervisor Password” sets a password that will be used to protect the system and the Setup utility; “User Password” sets a password that will be used exclusively on the system. By default, the system comes without any passwords. To specify a password, highlight the type you want and then press . A password prompt appears on the screen.
IV. BIOS SETUP IDE HDD Auto Detection This “IDE HDD Auto Detection” option detects the parameters of an IDE hard disk drive, and automatically enters them into the Standard CMOS Setup screen. IV. BIOS SETUP Hard Disk Detect Up to four IDE drives can be detected, with parameters for each listed inside the box. To accept the optimal entries, press or else select from the numbers displayed under the OPTIONS field (2, 1, 3 in this case); to skip to the next drive, press .
IV. BIOS SETUP IMPORTANT: If your hard disk was already formatted on an older previous system, incorrect parameters may be detected. You will need to enter the correct parameters manually or use low-level format if you do not need the data stored on the hard disk. If the parameters listed differ from the ones used when the disk was formatted, the disk will not be readable. If the auto-detected parameters do not match the ones that should be used for your disk, do not accept them.
(This page was intentionally left blank.
R SUPPORT CD ASUS P5S-VM User’s Manual 59
V. SOFTWARE SETUP ................................................... 61 Operating Systems ............................................................................ 61 Windows 98 First Time Installation ............................................ 61 P5S-VM Support CD ........................................................................ 62 Installation Menu ........................................................................ 62 LDCM Local Setup .....................................................
V. SOFTWARE SETUP Operating Systems You should always use the latest operating system and updates when using new hardware to ensure full compliancy. For Windows 95, you must use OSR 2.0 or later. For Windows NT 4.0, you must use Service Pack 3.0 or later. Windows 98 First Time Installation When you start Windows for the first time after the installation of your motherboard, Windows 98 will detect the onboard audio and video chips and may attempt to install a driver from its system registry.
V. SOFTWARE SETUP P5S-VM Support CD NOTE: The support CD contents are subject to change at any time without notice. To begin using your support CD disc, just insert it into your CD-ROM drive and the support CD installation menu should appear. If the menu does not appear, double click or run D:\SETUP.EXE (assuming that your CD-ROM drive is drive D:). Installation Menu • • • • • V.
V. SOFTWARE SETUP LDCM Local Setup Insert the Support CD that came with your motherboard into your CD-ROM drive or double-click the CD drive icon in My Computer to bring up the setup screen. NOTE: LDCM will not run if ASUS’ PC Probe utility is installed. To uninstall PC Probe, see section on Uninstalling Programs. 1. Click here. 2. Click here. 4. Click here. V. S/W SETUP Windows 98 3. Click here. 5. Click here. 6. Select the components you want to install and then click here.
V. SOFTWARE SETUP 7. Click here. 8. Click here. 9. Click here. V. S/W SETUP Windows 98 11. Click here and then click Finish to restart. 64 ASUS P5S-VM User’s Manual 10. Click here.
V. SOFTWARE SETUP LDCM Administrator Setup Insert the Support CD that came with your motherboard into your CD-ROM drive or double-click the CD drive icon in My Computer to bring up the setup screen. NOTE: LDCM will not run if ASUS’ PC Probe utility is installed. To uninstall PC Probe, see section on Uninstalling Programs. 1. Click here. 2. Click here. 4. Click here. V. S/W SETUP Windows 98 3. Click here. 5. Click here. ASUS P5S-VM User’s Manual 6. Click here and then click Finish to restart.
V. SOFTWARE SETUP ASUS PC Probe Setup Insert the Support CD that came with your motherboard into your CD-ROM drive or double-click the CD drive icon in My Computer to bring up the setup screen. NOTE: ASUS PC Probe will not run if Intel’s LDCM utility is installed. To uninstall Intel’s LDCM utility, see section on Uninstalling Programs. 2. Click here. 1. Click here. 3. Click here. V. S/W SETUP Windows 98 4. Make any desired setting changes and then click here. 5. Click here.
V. SOFTWARE SETUP Adobe Acrobat Reader Insert the Support CD that came with your motherboard into your CD-ROM drive or double-click the CD drive icon in My Computer to bring up the setup screen. 2. Click here. 1. Click here. 4. Click here. 3. Click here. ASUS P5S-VM User’s Manual V. S/W SETUP Windows 98 5. Click here.
V. SOFTWARE SETUP Install IDE Bus Master Driver Insert the Support CD that came with your motherboard into your CD-ROM drive or double-click the CD drive icon in My Computer to bring up the setup screen. This option is available only for Windows NT systems. 2. Click here and then click Next to start the installation. 1. Click here. 3. Select the mode* that you want to install and then click here. 4. Click here and then click OK to restart. *Transfer Modes Supported • V.
V. SOFTWARE SETUP Install Video Driver Insert the Support CD that came with your motherboard into your CD-ROM drive or double-click the CD drive icon in My Computer to bring up the setup screen. Install Video Driver installs the video driver necessary for your card to have higher performance, resolutions, and special features. 1. Click here. 2. Click here. 2. Click here to begin the installation wizard. 4. Click here. V. S/W SETUP Windows 98 3. Click here. 5.
V. SOFTWARE SETUP Install Audio Driver Insert the Support CD that came with your motherboard into your CD-ROM drive or double-click the CD drive icon in My Computer to bring up the setup screen. 2. Click here. 1. Click here. 4. Click here. 3. Click here. 6. Click here to start the installation. 5. Click here. V. S/W SETUP Windows 98 7. Click here. 70 8. Click here and then click Finish to restart.
V. SOFTWARE SETUP Install PC-Cillin Insert the Support CD that came with your motherboard into your CD-ROM drive or double-click the CD drive icon in My Computer to bring up the setup screen. 2. Click here. 1. Click here. 3. Enter the necessary information and then click here. 4. Click here. 6. Insert a floppy disk and then click here. V. S/W SETUP Windows 98 5. Click Express Install and then click here. 7. Once the Emergency Clean disk is created, click here.
V. SOFTWARE SETUP Uninstalling Programs Add/Remove Programs is a basic component within Windows. You may use this function if a program does not provide its own uninstallayyytion program. 1. Double-click here to open the Add/Remove Programs Properties dialog box. 2. Select the program you wish to remove and click here. V. S/W SETUP Windows 98 3. Click here.
VI. SOFTWARE REFERENCE VI. S/W REFERContents ENCE Intel LANDesk Client Manager With the growth of the computer industry, computer systems have become more complex and difficult to manage. Intel LANDesk Client Manager is a computer management application that simplifies many aspects of managing a computer and assists in troubleshooting common computer problems.
VI. SOFTWARE REFERENCE VI.
VI. SOFTWARE REFERENCE VI.
VI. SOFTWARE REFERENCE VI. S/W REFERIntelENCE LDCM To select a computer 1. From the main Client Manager window, click File | Select Computer. 2. In the Select Computer dialog box, click the computer you want to view. 3. Click the Select button. To discover new computers • In the Select Computer dialog box, click the Discover button on the toolbar or press +.
VI. SOFTWARE REFERENCE VI. S/W REFERIntelENCE LDCM After you attempt to wake up a computer, the status of that computer changes in the list view to a Wake Pending status. If the attempt to wake up a computer is successful, the Wake Pending status changes to a status reflecting the computer’s health (such as Normal, Warning, or Critical). If the computer does not wake up after five minutes, a message box appears stating possible reasons why the computer did not respond.
VI. SOFTWARE REFERENCE VI. S/W REFERIntelENCE LDCM Understanding the Computer Status Icons When you open the Select Computer dialog box, each computer in the list displays an icon indicating the current status of that computer. The table below describes the seven states a computer may be in. 78 Unavailable The computer is currently in a powered-down state. Wakeable The computer is currently in a powered-down state but supports Remote Wakeup technology.
VI. SOFTWARE REFERENCE VI. S/W REFERIntelENCE LDCM ASUS PC Probe ASUS PC Probe is a convenient utility to monitor the computer system’s vital components: fan rotations, voltages, and temperatures. Starting ASUS PC Probe When ASUS PC Probe starts, a splash screen appears allowing you to “Show Monitor” or “Hide”. You can select whether you want the splash screen to show the next time it opens.
VI. SOFTWARE REFERENCE VI.
VI. SOFTWARE REFERENCE VI. S/W REFERASUS ENCE PC Probe Using the ASUS PC Probe PC Probe System Info. Get information on your mainboard and BIOS from this screen. PC Probe Settings Change PC Probe refresh times here Click here to start PC Probe each time you enter Windows. Click the items you wish to reset to its default values and click this button. PC Probe Task Bar Icon Right clicking the PC Probe icon will bring up a menu to turn on, off, or exit ASUS PC Probe.
VI. SOFTWARE REFERENCE VI. S/W REFERSiS 530ENCE Properties SiS 530 Display Properties The built-in 2D/3D AGP VGA on the SiS 530 AGPset supports professional graphics design, gaming, learning, and business applications. To open the SiS 530 Properties dialog box, click Start, point to Settings, click Control Panel, double-click Display, click the Settings tab, and then the Advanced button. 82 General Adapter This displays the current font size of the selected monitor.
Performance Video Setting Specifies the degree of acceleration you want for your graphics hardware. Full acceleration is the fastest and is recommended for most computers. If your ocmputer is having problems and you suspect graphics acceleration to be the cause, use the highest setting at which you do not have problems. Allows you to adjust the brightness and contrast of the screen output.
VI. SOFTWARE REFERENCE VI. S/W REFERCreative Multimedia ENCE Decks Creative Multimedia Decks Creative Multimedia Decks is a collection of players that allows you to independently or concurrently control multimedia devices such as your CD-ROM drive and MIDI device. It consists of Creative Remote and other players such as Creative CD, Creative Wave, and Creative MIDI.
VI. SOFTWARE REFERENCE VI. S/W REFERCreativeENCE CD Player Creative CD Player Creative CD operates like a home CD player, letting you play audio CDs from CDROM drives on your PC.
VI. SOFTWARE REFERENCE VI. S/W REFERCreative ENCE MIDI Player Creative MIDI Player Creative MIDI is the player in the Multimedia Decks suite of players that lets you play MIDI files.
VI. SOFTWARE REFERENCE VI. S/W REFERCreative Remote ENCE Creative Remote Creative Remote is the main component of the Creative Multimedia Decks group of players. Like a home remote control, it lets you control different Creative Multimedia Decks players from a single control interface. If you require more control over a player, you can also invoke the player from Creative Remote.
VI. SOFTWARE REFERENCE VI. S/W REFERCreative ENCE Wave Player Creative Wave Player Creative Wave is the player in the Creative Multimedia Decks suite of players that lets you play wave files.
VI. SOFTWARE REFERENCE VI. S/W REFERAudio Mixer ENCE SB AudioPCI 64V Mixer A mixer has been included for Sound Blaster AudioPCI 64V. This mixer accommodates some features found on the AudioPCI card. These features are unavailable through the Windows 95/98 mixer. Real-Time Effects AudioPCI supports real-time effects. In addition to the effects described below, more effects may be available in the future. This effect provides a surround-sound effect.
VI. SOFTWARE REFERENCE VI. S/W REFERCreative ENCE WaveStudio Creative WaveStudio WaveStudio is a Windows-based application that allows you to perform the following sound editing functions easily: • • • • Play, edit, and record 8-bit (tape quality) and 16-bit (CD quality) wave data. Enhance your wave data or create unique sounds with various special effects and editing operations such as rap, reverse, echo, mute, pan, cut, copy, and paste. Open and edit several wave files at the same time.
VI. SOFTWARE REFERENCE VI. S/W REFERDIMENCE Utility Desktop Management Interface (DMI) Introducing the ASUS DMI Configuration Utility This motherboard supports DMI within the BIOS level and provides a DMI Configuration Utility to maintain the Management Information Format Database (MIFD). DMI is able to auto-detect and record information pertinent to a computer’s system such as the CPU type, CPU speed, and internal/external frequencies, and memory size.
VI. SOFTWARE REFERENCE VI. S/W REFERDMIENCE Utility Using the ASUS DMI Configuration Utility NOTE: The following screen displays are provided as examples only and may not reflect the screen contents on your system. Edit DMI (or delete) Use the ←→ (left-right) cursors to move the top menu items and the ↑↓ (up-down) cursor to move between the left hand menu items. The bottom of the screen will show the available keys for each screen. Press enter at the menu item to enter the right hand screen for editing.
VI. SOFTWARE REFERENCE VI. S/W REFERDIMENCE Utility Save MIFD You can save the MIFD (normally only saved to flash ROM) to a file by entering the drive and path here. If you want to cancel save, you may press ESC and a message “Bad File Name” appears here to show it was not saved. Load MIFD You can load the disk file to memory by entering a drive and path and file name here. Load BIOS Defaults You can load the BIOS defaults from a MIFD file and can clear all user modified and added data.
(This page was intentionally left blank.
VII. APPENDIX VII. APPENDIX ASUS LAN Card ASUS PCI-L101 Fast Ethernet Card LEDs LAN Activity Output Signal Intel Chipset RJ45 Wake on LAN Output Signal ASUS Motherboard type Other If you are using the ASUS PCI-L101 on an ASUS motherboard, leave the jumper on its defaut setting of “ASUS.” If you are using another brand of motherboard, set the jumper to “Other.” Connect the Wake on LAN (WOL) output signal to the motherboard’s WOL_CON in order to utilize the wake on LAN feature of the motherboard.
VII. APPENDIX Features VII. APPENDIX ASUS LAN Card • • • • • • • • • • • • Intel 82558 Ethernet LAN Controller (Fully integrated 10BASE-T/100BASE-TX) Wake-On-LAN Remote Control Function Supported PCI Bus Master Complies to PCI Local Bus Rev. 2.1 specifications Consists of MAC & PHY (10/100Mbps) interfaces Complies to IEEE 802.3 10BASE-T and IEEE 802.3u 100BASE-TX interfaces Fully supports 10BASE-T & 100BASE-TX operations through a single RJ45 port Supports 32-bit Bus Master Technology / PCI Rev. 2.
