User's Manual
Table Of Contents
- Contents
- Chapter 1: Product introduction
- Chapter 2: Hardware information
- Chapter 3: Powering up
- Chapter 4: BIOS setup
- 4.1 Managing and updating your BIOS
- 4.2 BIOS setup program
- 4.3 Main menu
- 4.4 Ai Tweaker menu
- 4.4.1 Ai Overclock Tuner [Auto]
- 4.4.2 CPU Ratio Setting [Auto]
- 4.4.3 FSB Strap to North Bridge [Auto]
- 4.4.4 DRAM Frequency [Auto]
- 4.4.5 DRAM Command Rate [Auto]
- 4.4.6 DRAM CMD Skew on Channel A/B [Auto]
- 4.4.7 DRAM CLK Skew on Channel A/B [Auto]
- 4.4.8 DRAM Timing Control [Auto]
- 4.4.9 DRAM Static Read Control [Auto]
- 4.4.10 DRAM Dynamic Write Control [Auto]
- 4.4.11 Ai Clock Twister [Auto]
- 4.4.12 Ai Transaction Booster [Auto]
- 4.4.13 CPU Voltage [Auto]
- 4.4.14 CPU PLL Voltage [Auto]
- 4.4.15 FSB Termination Voltage [Auto]
- 4.4.16 DRAM Voltage [Auto]
- 4.4.17 NB Voltage [Auto]
- 4.4.18 SB Voltage [Auto]
- 4.4.19 Clock Over-Charging Voltage [Auto]
- 4.4.20 Load-Line Calibration [Auto]
- 4.4.21 CPU GTL Voltage Reference [Auto]
- 4.4.22 NB GTL Voltage Reference [Auto]
- 4.4.23 CPU Spread Spectrum [Auto]
- 4.4.24 PCIE Spread Spectrum [Auto]
- 4.5 Advanced menu
- 4.6 Power menu
- 4.7 Boot menu
- 4.8 Tools menu
- 4.9 Exit menu
- Chapter 5: Software support
- Chapetr 6: ATI® CrossFire™ technology support
- Appendix: CPU features
4-28 Chapter 4: BIOS setup
4.5.3 Onboard Devices Conguration
Select Screen
Select Item
+- Change Option
F1 General Help
F10 Save and Exit
ESC Exit
v02.61 (C)Copyright 1985-2007, American Megatrends, Inc.
Onboard Device Conguraiton
High Denition Audio [Enabled]
Front Panel Type [HD Audio]
Marvell IDE/eSATA [Legacy Mode]
IDE/eSATA Boot ROM [Enabled]
PCIE GigaBit LAN1 [Enabled]
LAN Boot ROM [Disabled]
PCI GigaBit LAN2 [Enabled]
LAN Boot ROM [Disabled]
Fireware 1394 [Enabled]
Serial Port1 Address [3F8/IRQ4]
Enable or Disable
High Denition Audio
Controller
BIOS SETUP UTILITY
Advanced
High Denition Audio [Enabled]
Allows you to enable or disable the High Denition Audio.
Conguration options: [Enabled] [Disabled]
Front Panel Type [HD Audio]
This item appears only when you enable the previous item and allows you
to set the front panel audio connector (AAFP) mode to legacy AC’97 or high-
denition audio depending on the audio standard that the front panel audio
module supports.
Conguration options: [AC97] [HD Audio]
Marvell IDE/eSATA [Legacy Mode]
Set this item to [RAID Mode] to create a RAID set using the EXT_SATA1-2
connectors and the external SATA ports.
Conguration options: [Legacy Mode] [RAID Mode] [Disabled]
IDE/eSATA Boot ROM [Enabled]
This item appears only when you set the previous item to [Legacy Mode] or
[RAID Mode].
Conguration options: [Disabled] [Enabled]
Please install the Marvell
®
Controller driver before using the black Serial ATA
connectors (EXT_SATA1-2). Refer to 5.2.4 Make Disk menu for details.
PCIE GigaBit LAN1 [Enabled]
Conguration options: [Enabled] [Disabled]
LAN Boot ROM [Disabled]
This item appears only when you enable the previous item.
Conguration options: [Disabled] [Enabled]