User's Manual
Table Of Contents
- Contents
- Chapter 1: Product introduction
- Chapter 2: Hardware information
- Chapter 3: Powering up
- Chapter 4: BIOS setup
- 4.1 Managing and updating your BIOS
- 4.2 BIOS setup program
- 4.3 Main menu
- 4.4 Ai Tweaker menu
- 4.4.1 Ai Overclock Tuner [Auto]
- 4.4.2 CPU Ratio Setting [Auto]
- 4.4.3 FSB Strap to North Bridge [Auto]
- 4.4.4 DRAM Frequency [Auto]
- 4.4.5 DRAM Command Rate [Auto]
- 4.4.6 DRAM CMD Skew on Channel A/B [Auto]
- 4.4.7 DRAM CLK Skew on Channel A/B [Auto]
- 4.4.8 DRAM Timing Control [Auto]
- 4.4.9 DRAM Static Read Control [Auto]
- 4.4.10 DRAM Dynamic Write Control [Auto]
- 4.4.11 Ai Clock Twister [Auto]
- 4.4.12 Ai Transaction Booster [Auto]
- 4.4.13 CPU Voltage [Auto]
- 4.4.14 CPU PLL Voltage [Auto]
- 4.4.15 FSB Termination Voltage [Auto]
- 4.4.16 DRAM Voltage [Auto]
- 4.4.17 NB Voltage [Auto]
- 4.4.18 SB Voltage [Auto]
- 4.4.19 Clock Over-Charging Voltage [Auto]
- 4.4.20 Load-Line Calibration [Auto]
- 4.4.21 CPU GTL Voltage Reference [Auto]
- 4.4.22 NB GTL Voltage Reference [Auto]
- 4.4.23 CPU Spread Spectrum [Auto]
- 4.4.24 PCIE Spread Spectrum [Auto]
- 4.5 Advanced menu
- 4.6 Power menu
- 4.7 Boot menu
- 4.8 Tools menu
- 4.9 Exit menu
- Chapter 5: Software support
- Chapetr 6: ATI® CrossFire™ technology support
- Appendix: CPU features
2-32 Chapter 2: Hardware information
9. CPU, chassis, and power fan connectors
(4-pin CPU_FAN, 3-pin CHA_FAN1-4, 3-pin PWR_FAN)
The fan connectors support cooling fans of 350 mA~2000 mA (24 W max.)
or a total of 1 A~7 A (84 W max.) at +12V. Connect the fan cables to the fan
connectors on the motherboard, making sure that the black wire of each
cable matches the ground pin of the connector.
Do not forget to connect the fan cables to the fan connectors. Insufcient air
ow inside the system may damage the motherboard components. These are
not jumpers! Do not place jumper caps on the fan connectors!
Only the CPU-FAN and CHA-FAN 1-2 connectors support the ASUS Q-FAN 2
feature.
P5E64 WS EVOLUTION
®
P5E64 WS Evolution Fan connectors
CPU_FAN CHA_FAN1
CHA_FAN2
PWR_FAN
GND
CPU FAN PWR
CPU FAN IN
CPU FAN PWM
GND
Rotation
+12V
GND
Rotation
+12V
GND
Rotation
+12V
GND
Rotation
+12V
CHA_FAN3
GND
Rotation
+12V
CHA_FAN4
10. Chassis intrusion connector (4-1 pin CHASSIS)
This connector is for a chassis-mounted intrusion detection sensor or switch.
Connect one end of the chassis intrusion sensor or switch cable to this
connector. The chassis intrusion sensor or switch sends a high-level signal to
this connector when a chassis component is removed or replaced. The signal
is then generated as a chassis intrusion event.
By default, the pin labeled “Chassis Signal” and “Ground” are shorted with
a jumper cap. Remove the jumper caps only when you intend to use the
chassis intrusion detection feature.
P5E64 WS EVOLUTION
®
P5E64 WS Evolution Chassis intrusion connector
CHASSIS
+5VSB_MB
Chassis Signal
GND
(Default)