User's Manual
Table Of Contents
- Contents
- Chapter 1: Product introduction
- Chapter 2: Hardware information
- Chapter 3: Powering up
- Chapter 4: BIOS setup
- 4.1 Managing and updating your BIOS
- 4.2 BIOS setup program
- 4.3 Main menu
- 4.4 Ai Tweaker menu
- 4.4.1 Ai Overclock Tuner [Auto]
- 4.4.2 CPU Ratio Setting [Auto]
- 4.4.3 FSB Strap to North Bridge [Auto]
- 4.4.4 DRAM Frequency [Auto]
- 4.4.5 DRAM Command Rate [Auto]
- 4.4.6 DRAM CMD Skew on Channel A/B [Auto]
- 4.4.7 DRAM CLK Skew on Channel A/B [Auto]
- 4.4.8 DRAM Timing Control [Auto]
- 4.4.9 DRAM Static Read Control [Auto]
- 4.4.10 DRAM Dynamic Write Control [Auto]
- 4.4.11 Ai Clock Twister [Auto]
- 4.4.12 Ai Transaction Booster [Auto]
- 4.4.13 CPU Voltage [Auto]
- 4.4.14 CPU PLL Voltage [Auto]
- 4.4.15 FSB Termination Voltage [Auto]
- 4.4.16 DRAM Voltage [Auto]
- 4.4.17 NB Voltage [Auto]
- 4.4.18 SB Voltage [Auto]
- 4.4.19 Clock Over-Charging Voltage [Auto]
- 4.4.20 Load-Line Calibration [Auto]
- 4.4.21 CPU GTL Voltage Reference [Auto]
- 4.4.22 NB GTL Voltage Reference [Auto]
- 4.4.23 CPU Spread Spectrum [Auto]
- 4.4.24 PCIE Spread Spectrum [Auto]
- 4.5 Advanced menu
- 4.6 Power menu
- 4.7 Boot menu
- 4.8 Tools menu
- 4.9 Exit menu
- Chapter 5: Software support
- Chapetr 6: ATI® CrossFire™ technology support
- Appendix: CPU features
ASUS P5E64 WS Evolution 5-39
Creating a RAID 10 set
To create a RAID 10 set:
1. From the utility main menu, select 1. Create RAID Volume, then press
<Enter>. This screen appears.
Intel(R) Matrix Storage Manager Option ROM v5.0.0.1032 ICH7R wRAID5
Copyright(C) 2003-05 Intel Corporation. All Rights Reserved.
[ CREATE ARRAY MENU ]
[ DISK/VOLUME INFORMATION ]
Enter a string between 1 and 16 characters in length that can be used
to uniquely identify the RAID volume. This name is case sensitive and
cannot contain special characters.
Name:
RAID Level:
Disks:
Strip Size:
Capacity:
Volume10
RAID10(RAID0+1)
Select Disks
128KB
XXX.X GB
Create Volume
2. Enter a name for the RAID 10 set, then press <Enter>.
3. When the RAID Level item is highlighted, press the up/down arrow key to
select RAID 10, then press <Enter>.
4. When the Stripe Size item is highlighted, press the up/down arrow key to
select the stripe size for the RAID 10 array, then press <Enter>. The available
stripe size values range from 4 KB to 128 KB. The default stripe size is 64
KB.
TIP: We recommend a lower stripe size for server systems, and a higher stripe
size for multimedia computer systems used mainly for audio and video editing.
5. Key in the RAID volume capacity that you want then press <Enter> when
the Capacity item is highlighted. The default value indicates the maximum
allowed capacity.
[
↑↓
]-Change [TAB]-Next [ESC]-Previous Menu [Enter]-Select