User's Manual
Table Of Contents
- Contents
- Chapter 1: Product introduction
- Chapter 2: Hardware information
- Chapter 3: Powering up
- Chapter 4: BIOS setup
- 4.1 Managing and updating your BIOS
- 4.2 BIOS setup program
- 4.3 Main menu
- 4.4 Ai Tweaker menu
- 4.4.1 Ai Overclock Tuner [Auto]
- 4.4.2 CPU Ratio Setting [Auto]
- 4.4.3 FSB Strap to North Bridge [Auto]
- 4.4.4 DRAM Frequency [Auto]
- 4.4.5 DRAM Command Rate [Auto]
- 4.4.6 DRAM CMD Skew on Channel A/B [Auto]
- 4.4.7 DRAM CLK Skew on Channel A/B [Auto]
- 4.4.8 DRAM Timing Control [Auto]
- 4.4.9 DRAM Static Read Control [Auto]
- 4.4.10 DRAM Dynamic Write Control [Auto]
- 4.4.11 Ai Clock Twister [Auto]
- 4.4.12 Ai Transaction Booster [Auto]
- 4.4.13 CPU Voltage [Auto]
- 4.4.14 CPU PLL Voltage [Auto]
- 4.4.15 FSB Termination Voltage [Auto]
- 4.4.16 DRAM Voltage [Auto]
- 4.4.17 NB Voltage [Auto]
- 4.4.18 SB Voltage [Auto]
- 4.4.19 Clock Over-Charging Voltage [Auto]
- 4.4.20 Load-Line Calibration [Auto]
- 4.4.21 CPU GTL Voltage Reference [Auto]
- 4.4.22 NB GTL Voltage Reference [Auto]
- 4.4.23 CPU Spread Spectrum [Auto]
- 4.4.24 PCIE Spread Spectrum [Auto]
- 4.5 Advanced menu
- 4.6 Power menu
- 4.7 Boot menu
- 4.8 Tools menu
- 4.9 Exit menu
- Chapter 5: Software support
- Chapetr 6: ATI® CrossFire™ technology support
- Appendix: CPU features
5-38 Chapter 5: Software support
Creating a RAID 1 set (mirrored)
To create a RAID 1 set:
1. From the utility main menu, select 1. Create RAID Volume, then press
<Enter>. This screen appears.
2. Enter a name for the RAID 1 set, then press <Enter>.
3. When the RAID Level item is highlighted, press the up/down arrow key to
select RAID 1(Mirror), then press <Enter>.
4. When the Capacity item is highlighted, key in the RAID volume capacity that
you want, then press <Enter>. The default value indicates the maximum
allowed capacity.
5. Press <Enter> when the Create Volume item is highlighted. This warning
message appears.
Intel(R) Matrix Storage Manager Option ROM v5.0.0.1032 ICH7R wRAID5
Copyright(C) 2003-05 Intel Corporation. All Rights Reserved.
[ CREATE ARRAY MENU ]
[ DISK/VOLUME INFORMATION ]
Enter a string between 1 and 16 characters in length that can be used
to uniquely identify the RAID volume. This name is case sensitive and
cannot contain special characters.
[↑↓]-Change [TAB]-Next [ESC]-Previous Menu [Enter]-Select
Name:
RAID Level:
Disks:
Strip Size:
Capacity:
Volume1
RAID1(Mirror)
Select Disks
N/A
XX.X GB
Create Volume
WARNING: ALL DATA ON SELECTED DISKS WILL BE LOST.
Are you sure you want to create this volume? (Y/N):
6. Press <Y> to create the RAID volume and return to main menu or <N> to go
back to Create Volume menu.