A7V600 Motherboard ®
Checklist ii
iii Features
Safeguards ® ® iv
Federal Communications Commission Statement This device complies with FCC Rules Part 15. Operation is subject to the following two conditions: • • This device may not cause harmful interference, and This device must accept any interference received including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
vi
vii
viii
® ( ) ix
* x
1 2 3 4 5 6 7 8 9 18 17 10 11 16 15 14 20 19 13 12 21 22 23 24 29 28 27 26 25
®
24.5cm (9.6in) PS/2KBMS T: Mouse B: Keyboard OVER_VOLT1 CPU_FAN VIA KT600 USB2.
A7V600 SB_PWR ® A7V600 Onboard LED ON Standby Power OFF Powered Off
CPU NOTCH TO INNER CORNER AMD™ CPU A7V600 ® A7V600 Socket A CPU NOTCH LEVER LOCK
® A7V600 184-Pin DDR DIMM Sockets 104 Pins 80 Pins DIMM3 DIMM2 DIMM1 A7V600
A7V600 ® Keyed for 1.
A7V600 ® WIFI A7V600 WIRELESS Connectors
USBPW12 USBPW34 2 3 1 2 +5V (Default) A7V600 +5VSB USBPW78 USBPW56 2 3 1 2 ® A7V600 USB Device Wake Up +5V (Default) +5VSB KBPWR 1 2 +5V (Default) A7V600 ® A7V600 Keyboard Power Setting 2 3 +5VSB
CLRTC A7V600 2 1 Clear CMOS ® 3 2 Normal (Default) A7V600 Clear RTC RAM OVER_VOLT1 1 2 Enable A7V600 ® A7V600 OVER_VOLT Setting 2 3 Disable (Default)
SEC_IDE PRI_IDE A7V600 ® PIN 1 A7V600 IDE Connectors PIN 1 NOTE: Orient the red markings (usually zigzag) on the IDE ribbon cable to PIN 1.
FLOPPY NOTE: Orient the red markings on the floppy ribbon cable to PIN 1.
Rotation +12V GND GND +12V Rotation PWR_FAN CPU_FAN A7V600 Rotation +12V GND CHA_FAN ® A7V600 12-Volt Fan Connectors ATXPWR1 A7V600 ® A7V600 ATX Power Connector +3.3VDC -12.0VDC GND PS_ON# GND GND GND -5.0VDC +5.0VDC +5.0VDC +3.3VDC +3.3VDC GND +5.0VDC GND +5.0VDC GND PWR_OK +5VSB +12.
A7V600 USB 2.
+5V J1B2 J1CY GND GND J1CX J1B1 +5V A7V600 GAME MIDI_IN J2B2 J2CY MIDI_OUT J2CX J2B1 +5V ® A7V600 Game Connector COM2 PIN 1 A7V600 ® A7V600 Serial COM2 Bracket
SPDIFOUT GND A7V600 +5V SPDIF_OUT2 ® BLINE_OUT_L AGND +5VA BLINE_OUT_R A7V600 Digital Audio Connector A7V600 ® A7V600 Front Panel Audio Connector MIC2 MICPWR Line out_R NC Line out_L FP_AUDIO
A7V600 ® IDE_LED SMI Lead A7V600 System Panel Connectors Reset Ground Power LED +5V Ground Ground Speaker GND RSATA_TXP1 RSATA_TXN1 GND RSATA_RXP1 RSATA_RXN1 GND GND RSATA_TXP2 RSATA_TXN2 GND RSATA_RXP2 RSATA_RXN2 GND A7V600 SATA Connectors PLED- PLED+ SATA2 ExtSMI# Ground PWR Ground IDE_LED+ IDE_LED- A7V600 SATA1 ® Speaker Connector Reset SW ATX Power Switch* * Requires an ATX power supply.
ASUS EZ Flash V1.00 Copyright (C) 2002, ASUSTeK COMPUTER INC.
[BIOS Information in File] BIOS Version: A7V600 Boot Block WARNING! Continue to update the BIOS (Y/N)? _ Flash Memory: SST 49LF004 1. Update Main BIOS area 2.
\ \ \ \
\ \ \
Bad BIOS checksum. Starting BIOS recovery... Checking for floppy... Bad BIOS checksum. Starting BIOS recovery... Checking for floppy... Floppy found! Reading file “A7V600.rom”. Completed. Start flashing...
Bad BIOS checksum. Starting BIOS recovery... Checking for floppy... Bad BIOS checksum. Starting BIOS recovery... Checking for floppy... Floppy not found! Checking for CD-ROM... CD-ROM found. Reading file “A7V600.rom”. Completed. Start flashing...
CD ON/OFF PLAY/PAUSE Esc F1 STOP/EJECT F2 PREVIOUS NEXT F3 F4 VOL. DOWN VOL. UP F5 F6 F7 CAPS LOCK LED CD ON/OFF PLAY/PAUSE STOP/EJECT PREVIOUS VOL. DOWN NEXT VOL.
®
® • • ®
® VIA Tech. RAID BIOS Ver 0.96 Create Array Delete Array Create/Delete Spare Select Boot Array Serial Number View Channel Channel0 Channel0 Channel1 Channel1 ↑ ↓ Drive Name Master Slave Master Slave XXXXXXXXXX XXXXXXXXXX No Drive No Drive Create a RAID array with the hard disk attached to VIA IDE controller F1 : , : Enter: ESC : Array Name View Array/Disk Status Move to next item Confirme the selection Exit Mode Size(GB) xxxxx xxxxx xxx.xx xxx.
VIA Tech. RAID BIOS Ver 0.
4K 8K 16K 32K 64K The data on the selected disks will be destroyed.
The data on the selected disks will be destroyed.
The data on the selected disks will be destroyed. Continue? Press Y/N “Y” “N” The selected array will be destroyed. Are you sure? Continue? Press Y/N “Y” “N” ESC Channel [ ]Channel0 Master [ ]Channel0 Slave Channel1 Master Channel1 Slave Drive Name XXXXXXXXXX XXXXXXXXXX No Drive No Drive Array Name : Exit Mode xxxxxxx xxxxxxx Size(GB) Status xxx.xx xxx.
VIA Tech. RAID BIOS Ver 0.96 Create a RAID array with the hard disk attached to VIA IDE controller Create Array Delete Array Create/Delete Spare Select Boot Array Serial Number View Channel Channel0 Channel0 Channel1 Channel1 F1 : , : Enter: ESC : Drive Name Master Slave Master Slave Serial Number: XXXXXXXXXX XXXXXXXXXX No Drive No Drive VJF41646 Array Name View Array/Disk Status Move to next item Confirme the selection Exit Mode Size(GB) xxxxx xxxxx xxx.xx xxx.
®
