User Guide

ASUS MEL User’s Manual 13
III. HARDWARE SETUP
Motherboard Settings
1) KBPWR p. 14 Keyboard Power Up (Enable/Disable)
2) DIP5, REQ5, GNT5 p. 15 Onboard Audio Settings
3) DIP6 p. 15 VIO Setting
4) DIP1,2,3 p. 16 CPU Bus Frequency
5) DIP7,8,9,10 p. 16 CPU Core:Bus Frequency Multiple
Expansion Slots
1) DIMM1,2,3,4 p. 17 168-Pin DIMM Memory Support
2) Socket 370 p. 19 Central Processing Unit (CPU) Socket
3) SLOT1, SLOT2 p. 21 16-bit ISA Bus Expansion Slots
*
4) PCI1,2,3,4,5 p. 21 32-bit PCI Bus Expansion Slots
5) AGP p. 22 Accelerated Graphics Port
Connectors
1) PS2KBMS p. 23 PS/2 Mouse Connector (6-pin female)
2) PS2KBMS p. 23 PS/2 Keyboard Connector (6-pin female)
3) USB p. 24 Universal Serial BUS Ports 1 & 2 (Two 4-pin female)
4) PRINTER p. 24 Parallel Port Connector (25-pin female)
5) COM1, COM2 p. 24 Serial Port COM1 and COM2 Connectors (9-pin male)
6) GAME_AUDIO p. 25 Joystick/Midi Connector (15-pin female) (optional)
7) GAME_AUDIO p. 25 Audio Port Connectors (Three 1/8” female) (optional)
8) ATXPWR p. 25 ATX Power Supply Connector (20 pins)
9) PRIMARY/SECONDARY IDE p. 26 Primary/Secondary IDE Connectors (Two 40-1pins)
10) FLOPPY p. 26 Floppy Disk Drive Connector (34-1pins)
11) CHA_, CPU_, PWR_FAN p. 27 Chassis, CPU, Power Supply Fan Connectors (Three 3-pin)
12) WOL_CON p. 27 Wake-On-LAN Connector (3 pins)
13) WOR p. 28 Wake-On-Ring Connector (2 pins)
14) IR p. 28 IrDA-Compliant Infrared Module Connector (5 pins)
15) IDELED p. 29 IDE LED Activity Light (2 pins)
16) SBLINK p. 29 SB-Link
TM
Connector (6-1 pins)
17) MODEM p. 29 Modem Card Voice In Connector (4 pins)
18) SMB p. 30 SMBus Connector (5-1 pins)
19) AUX/CD1/CD2 p. 30 Stereo Audio In Connectors (Three 4-pin)
20) MSG.LED (PANEL) p. 31 System Message LED (2 pins)
21) SMI (PANEL) p. 31 SMI Switch Lead (2 pins)
22) PWR.SW (PANEL) p. 31 ATX Power & Soft-Off Switch Lead (2 pins)
23) RESET (PANEL) p. 31 Reset Switch Lead (2 pins)
24)
PWR.LED ( PANEL ) p. 31 System Power LED Lead (3-1 pins)
25)
KEYLOCK ( PANEL ) p. 31 Keyboard Lock Switch Lead (2 pins)
26) SPEAKER (PANEL) p. 31 System Warning Speaker Connector (4 pins)
27) CHASIS p. 32 Chassis Intrusion Sensor Lead (4-1 pins)
*
The onboard hardware monitor uses the address 290H-297H so legacy ISA cards
must not use this address; otherwise, conflicts will occur.
Layout Contents
III. H/W SETUP