User Manual
Table Of Contents
- Chapter 1
- Chapter 2
- Chapter 3
- BIOS setup
- 3.1 BIOS setup program
- 3.2 Main menu
- 3.3 Ai Tweaker menu
- 3.3.1 CPU Power Enhancement
- 3.3.2 CPU Core Ratio
- 3.3.3 DRAM Odd Ratio Mode
- 3.3.4 DRAM Frequency
- 3.3.5 Power-saving & Performance Mode
- 3.3.6 DRAM Timing Control
- 3.3.7 DIGI+ VRM
- 3.3.8 Internal CPU Power Management
- 3.3.9 CPU Core/Cache Current Limit Max.
- 3.3.10 CPU Graphics Current Limit
- 3.3.11 Min. CPU Cache Ratio
- 3.3.12 Max. CPU Cache Ratio
- 3.3.13 Max. CPU Graphics Ratio
- 3.3.14 DRAM Voltage
- 3.3.15 DRAM REF Voltage Control
- 3.4 Advanced menu
- 3.4.1 Platform Misc Configuration
- 3.4.2 CPU Configuration
- 3.4.3 System Agent (SA) Configuration
- 3.4.4 PCH Configuration
- 3.4.5 PCH Storage Configuration
- 3.4.6 PCH-FW Configuration
- 3.4.7 Onboard Devices Configuration
- 3.4.8 APM Configuration
- 3.4.9 Serial Console Redirection
- 3.4.10 PCI Subsystem Settings
- 3.4.11 USB Configuration
- 3.4.12 Network Stack Configuration
- 3.4.13 HDD Secure Erase
- 3.4.14 HDD/SSD SMART Information
- 3.5 Monitor menu
- 3.6 Boot menu
- 3.7 Tool menu
- 3.8 Exit menu
- BIOS setup
- Appendix
3-24
H310A-EM-A
Device Mode [STD Printer Mode]
Allows you to change the Printer Port mode.
Conguration options: [STD Printer Mode] [SPP Mode] [EPP-1.9 and SPP
Mode] [EPP-1.7 and SPP Mode] [ECP Mode] [ECP and EPP 1.9 Mode] [ECP
and EPP 1.7 Mode]
3.4.8 APM Conguration
ErP Ready [Disabled]
Allows BIOS to switch off some power at S5 to get the system ready for ErP
requirement. When set to [Enabled], all other PME options will be switched off.
Conguration options: [Enable(S4+S5)] [Enable(S5)] [Disabled]
CEC Ready [Disabled]
Enable this item to allow your system to comply with CEC (California Energy
Commission) regulations to save some power at S0 state. Conguration options:
[Enable] [Disabled]
Restore AC Power Loss [Power Off]
Allows you to select AC power state when power is re-applied after a power failure.
Conguration options: [S5 State] [S0 State] [Last State]
Power On By PCI-E/PCI [Disabled]
This item allows you to enable or disable the Wake-on-LAN function of the onboard
LAN controller or other installed PCIe LAN cards. Conguration options: [Disabled]
[Enabled]
Power On By Ring [Disabled]
[Disabled] Disables the Ring devices to generate a wake event.
[Enabled] Enables the Ring devices to generate a wake event.
Power On By RTC [Disabled]
This item allows you to enable or disable the RTC (Real-Time Clock) to generate
a wake event and congure the RTC alarm date. When enabled, you can set the
days, hours, minutes, or seconds to schedule an RTC alarm date. Conguration
options: [Disabled] [Enabled]