NOTEBOOK PC USER’S MANUAL
Product Name: Notebook PC Manual Revision: 1.
FCC and DOC Safety Statements Federal Communications Commission Statement This device complies with FCC Rules Part 15. Operation is subject to the following two conditions: • • This device may not cause harmful interference, and This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the Federal Communications Commission (FCC) rules.
Notebook PC with Lithium-Ion Battery Nordic Caution Statements CAUTION! Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions. (English) VORSICHT! Explosionsgetahr bei unsachgemäßen Austausch der Batterie. Ersatz nur durch denselben oder einem vom Hersteller empfohlenem ähnlichen Typ. Entsorgung gebrauchter Batterien nach Angaben des Herstellers.
Contents SECTION 1 INTRODUCTION This Product ........................................................................................................................................ 9 This User’s Manual ............................................................................................................................. 9 Notes Used in This Manual ............................................................................................................ 9 Hardware Features ..........................
Contents (Cont’) Restarting or Rebooting ...................................................................................................................... 26 LED Indicators ..................................................................................................................................... 26 System Status Panel ........................................................................................................................... 27 System Status Panel Descriptions .................
Contents (Cont’) SECTION 5 USING THE NOTEBOOK PC Introduction ......................................................................................................................................... 51 Storage Device Modules ..................................................................................................................... 51 Floppy Drive ........................................................................................................................................
Contents (Cont’) AC Power System ............................................................................................................................... 61 Battery Power System ......................................................................................................................... 61 Inserting the Battery Pack .............................................................................................................. 62 Removing the Battery Pack ...................................
SECTION 1 I. Introduction INTRODUCTION This Product The Notebook PC is the latest in PC technology with features that surpass most desktop PCs. Since the number of features and components are so numerous, there may be different models for your market. Your dealer should provide you with a standard component checklist and a list of optional components for the Notebook PC. Your dealer should also provide you with warrranty and technical support.
Hardware Features I. Introduction The Notebook PC features a wide range of standard features, upgrades, and options. The following gives you all your current choices, many future options are being developed to keep up with the latest PC technologies. 10 • Processor: 233MHz to 300MHz A state-of-the-art Intel Pentium® II MMX Mobile Module supports future processor upgrades from the standard configuration of 233MHz. The Pentium® II has 32KB internal cache and 512KB Pipeline Burst Level-2.
• Fax/Modem: 56K V.90 An optional built-in 56K modem with V.90 compression and 19.2K fax is available on each model. The fax/ modem supports video-conferencing I/F V.80 and host-based digital voice and data. • LCD Status Panel: The LCD status panel displays AC-in, battery charging, battery gauge, hard disk/CD-ROM/floppy access, PC card, suspend, caps lock, scroll lock, and number lock statuses.
Caring Information I. Introduction CAUTION! The following safety precautions will increase the life of the Notebook PC. Follow all precautions and instructions. Except as described in this manual, refer all servicing to qualified personnel. Do not use damaged power cords, accessories, or other peripherals. Do not use strong solvents such as thinners, benzene or other chemicals on or near the surface. Disconnect the AC power and remove the battery pack(s) before cleaning.
Transporting the Notebook PC I. Introduction To prepare the Notebook PC for transport, you should turn it off and disconnect all external peripherals to prevent damage to the connectors. The hard disk drive’s head retracts when the power is turned off to prevent scratching of the hard disk surface during transport. Therefore, you should not transport the Notebook PC while the power is still on.
SECTION 2 COMPONENTS Top Side II.
Top Component Descriptions The following describes the top components of the Notebook PC as shown by the picture on the previous page. Display Panel Latches: The display panel latches lock the display panel in the closed position. Display Panel: The display panel uses active matrix TFT LCD technology and provides viewing like that of desktop monitors. II. Components Microphone: The built-in microphone provides a source for inputting mono audio.
Front/Rear Illustrations Front Side Refer to the diagram below to identify the components on the front side of the Notebook PC. II. Components Infrared Port Power Switch (slides to the right) LED Indicators Rear Side Refer to the diagram below to identify the components on the rear side of the Notebook PC.
Front/Rear Component Descriptions Front Side The following describes the front components to the Notebook PC as shown by the picture on the previous page. Infrared Port: The infrared (IrDA) communication port allows wireless data transfers through the front. LED Indicators: The orange LED will blink when the battery pack is charging. The Green LED will be lit when the power is on and blink when in standby (suspend) mode. II. Components Power Switch: The power switch is used to turn the power ON and OFF.
Left/Right Illustrations Left Side Refer to the diagram below to identify the components on the left side of the Notebook PC. Display Latch (slides to the right) 2 PCMCIA Sockets II. Components reset Reset Button Audio Line-Out Audio Line-In Headphone Jack Microphone-In Cooling Fan Volume Knob Floppy Disk Drive Hard Disk Drive Right Side Refer to the diagram below to identify the components on the right side of the Notebook PC.
Left/Right Component Descriptions Left Side The following describes the left-side components to the Notebook PC as shown by the picture on the previous page. reset II. Components PCMCIA: PCMCIA 2.1 compliant sockets for two Type I, Type II, or one Type III PC cards are available on every model.
Bottom Illustration Bottom Side Refer to the diagram below to identify the components on the bottom side of the Notebook PC. CD-ROM Latch (slides toward back) II.
Bottom Component Descriptions Bottom Side The following describes the bottom components to the Notebook PC as shown by the picture on the previous page. CD-ROM Latch: The CD-ROM latch locks the CD-ROM in place when inserted. Slide the latch toward the back of the Notebook PC to release the lock. CD-ROM Drive: (see right side) II. Components Tilting Legs: The two legs on the bottom of the Notebook PC can be flipped out to provide a comfortable typing angle.
(This page was intentionally left blank.) II.
SECTION 3 GETTING STARTED Power Connection Your Notebook PC comes with a universal AC-DC converter. This means that you may connect the power cord to any 110V-120V outlet as well as 220V-240V outlets without setting switches or using power converters. Different countries may require that an adapter be used to connect the provided US-standard AC power cord to a different standard. Most hotels will provide universal outlets to support different power cords as well as voltages.
PS/2 Connection A PS/2 mouse or PS/2 keyboard may be connected to the single PS/2 port. If you wish to connect two PS/2 devices, you need to use the included PS/2 Y-adapter. The following shows both a PS/2 mouse and PS/2 keyboard connected to the Notebook PC simultaneously using the PS/2 Y-adabpter. PS/2 Keyboard (not provided) PS/2 Y-Adapter PS/2 Mouse TV Connection (not provided) III.
Powering On Your Notebook PC Slide the power switch forward momentarily and the Notebook PC’s power-on message will appear on the screen followed by a short beep. If necessary, you may adjust the brightness by using the hot keys. If you need to run the BIOS Setup to set or modify the system configuration, press [F2] upon bootup to enter the BIOS Setup. To turn off the Notebook PC, slide and hold the power switch until the power turns off.
Restarting or Rebooting After installing drivers, installing applications, or making configuration changes, you may be prompted to restart the system to update the operating system and complete the installation process. To restart the system, use the “Restart the computer?” command in Windows “Start | Shut Down.” If this does not restart the Notebook PC, you can reset the Notebook PC by press the [Ctrl] + [Alt] + [Del] keys simultaneously.
System Status Panel Located under the display panel, the System Status Panel informs you of the Notebook PC’s current operating status at a glance. Upon activating a certain function, a symbol or icon corresponding to that function appears in the window indicating that the particular function is engaged. The icon will remain in the window until you deactivate that function. The figure below shows the System Status Panel with all the displayable icons.
Using the Keyboard Specific Hot Keys Some of the Notebook PC’s interface functions can be accessed through the keyboard by simultaneouly pressing the bottom-left “Fn” key and one of the funtions colored in blue. The following table lists the hot key functions for the Notebook PC. Increases display brightness Decreases display brightness Suspend Mode Toggles Embedded keypad lock off and on Toggles display panel off and on III. Starting Toggles between LCD and external CRT/LCD monitors.
Using the Keyboard (Cont’) Keyboard as a Numeric Keypad The embedded numeric keypad consists of 15 keys that make number intensive input more convenient. Like the [Num Lock] key, these keys are labeled in blue on the keycaps. Numeric assignments are located at the upper right hand corner of each key as shown in the figure. .
Using the Keyboard (Cont’) Numeric Keypad as Cursors The numberic keypad can be used as cursors. To enable the cursor keypad, press [ Fn ]+[ ] and then press [ Fn ]+[ NumLk ] to enable the embedded numeric keypad and disable the NumLock. The icon appears on the system status panel. III. Starting TV _ { [ " This is how your keys function under this feature.
SECTION 4 BIOS SETUP Introduction The BIOS (Basic Input and Output System) Setup is a menu driven software utility that enables you to make changes to the system configuration and tailor your Notebook PC to reflect installed hardware, alter performance, and setup power saving functions. It is a ROM-based program and also can be flashed with the latest version update through executing a specific BIOS flashing utility program bundled in the Driver & Utility CD-ROM.
BIOS Setup Program The Setup program has been designed to make it as easy to use as possible. It is a menu driven program, which means you can scroll through the various sub-menus and make your selections among the various predetermined choices. If you accidentally change a setting and do not know which one to switch back to, the Setup program has a hot key that allows you to return to the previous value. The hot keys are discussed in more detail later in this Section.
BIOS Setup Program (Cont’) Legend Bar At the bottom of the Setup screen you will notice a legend bar. The keys in the legend bar allow you to navigate through the various setup menus. The following table lists the keys found in the legend bar with their corresponding alternates and functions.
BIOS Setup Program (Cont’) General Help In addition to the Item Specific Help window, the BIOS setup program also provides a General Help screen. This screen can be called up from any menu by simply pressing [F1] or the [Alt] + [H] combination. The General Help screen lists the legend keys with their corresponding alternates and functions. Saving Changes and Exiting the Setup Program Refer to the Exit Menu Section of this Section for detailed information on saving changes and exiting the setup program.
Main Menu (Cont’) System Time Sets your system to the time that you specify (usually the current time). The format is hour, minute, second. Insert the appropriate information. Use the [Tab] or [Shift] + [Tab] keys to move between the hour, minute, and second fields. System Date Sets your system to the date that you specify (usually the current date). The format is month, day, year. Type in the appropriate information. Use the [Tab] or [Shift] + [Tab] keys to move between the month, day, and year fields.
Main Sub-Menu IDE Primary Master This field is used to configure the IDE Hard Disk installed in the system. To configure a hard disk drive, move the cursor to highlight the IDE Primary Master field and press the Enter key to enter the sub-menu.
Main Sub-Menu (Cont’) Type Select Auto to automatically detect an IDE type drive. This option only works with standard built-in IDE drives. If automatic detection is successful, the correct values will be filled in for the remaining fields on this sub-menu. To configure a drive, select User. Manually enter the number of cylinders, heads and sectors per track for your drive. Refer to your drive documentation or look on the drive for this information.
Main Sub-Menu (Cont’) LBA (Logical Block Addressing) Mode Control When enabled, this option uses 28-bit addressing of the hard drive without regard for cylinders, heads, or sectors. Note that Logical Block Access may decrease the access speed of the hard disk. However, LBA Mode is necessary for drives with greater than 504MB in storage capacity. NOTE: To make changes to this field, the Type field must be set to User.
Main Sub-Menu (Cont’) IDE Primary Slave In this field, indicate the size of the disk drive or the device type, such as a CD-ROM drive. The arrow head icon indicates that this field contains a sub-menu. The sub-menu is used to configure the IDE Hard Disk installed in the system. To configure a hard disk drive, move the cursor to highlight the IDE Primary Slave field, and press [Enter]. The submenu screen will appear.
Advanced Menu Selecting Advanced from the menu bar displays the Advanced menu. See the figure below.
Advanced Menu (Cont’) TV Mode Specifies the type of TV video output format for connecting to TV sets. Available formats are: [NTSC] [PAL] IR position There is one infrared port in the back and one infrared port in the front of the Notebook PC. Only one port may be used at one time. This field allow you to choose whether you want to use the front or the back infrared port. [Front] [Back] Internal Pointing Device This field allows you to enable or disable the internal pointing device.
Advanced Sub-Menu I/O Device Configuration Main Advanced PhoenixBIOS Setup Utility Security Power Boot I/O Device Configuration Seral port A: Base I/O address: IR Port Base I/O address: Mode: DMA Channel Parallel Port: Mode: Base I/O address: F1 Help Esc Exit Item Specific Help Configure serial port A using options: [User] [3F8 IRQ4] [User] [2F8 IRQ3] [FIR] [DMA 3] [User] [Bi-directionl] [378/IRQ7] Select Item Select Menu Enter Exit Auto [BIOS configuration] User [USER configuration] Disabled [NO
Advanced Sub-Menu (Cont’) When User is selected, the Base I/O address menu item appears. This Mode field allows you to enable or disable the Notebook PC’s Fast Infrared (FIR) communication module. The following configuration options are available: [SIR] [FIR] NOTE! The DMA channel menu item is available only when FIR is selected. The COM2 serial port is available for system use only if the serial IR is Disabled. SIR enables standard IrDA IR support on COM2.
Advanced Sub-Menu (Cont’) ECP Mode: The port is both software and hardware compatible with existing parallel ports so that it may be used as a standard printer mode if ECP is not required. ECP mode provides an automatic high burst-bandwidth channel that supports DMA for ECP in both the forward (host to peripheral) and reverse (peripheral to host) direction. Options in the field of Base I/O address are used to choose the I/O (port) address for the Parallel port.
Security Menu (Cont’) The Notebook PC’s advanced system of security allows you to set a password to prevent unauthorized access to system resources, data, and the BIOS Setup Program. This Section covers each parameter of the Security Setup. Selecting Security from the menu bar displays the following menu: A Note about Passwords The BIOS Setup program allows you to specify passwords in the Security menu. The passwords control access to the BIOS and certain Security menu options during system startup.
The Power Menu The Power menu of the Setup program allows you to enable and adjust the advanced features of the Notebook PC, which are designed to conserve power. Enabling these features will extend the life of the battery pack between charges. To make changes to power management settings, select Power Savings from the menu bar.
Power Menu (Cont’) Standby Timeout This option is only enabled when Customized is selected in the Power Savings field. This field allows you to specify the period of inactivity before the system automatically switches to Standby mode. In Standby mode, various devices including the LCD backlight are powered off and the system enters a low power CPU state.
Boot Menu The Boot menu allows the user to specify the order in which the Notebook PC is to check for a device to boot the system. To make changes, select Boot from the menu bar and the following screen appears: Main Advanced PhoenixBIOS Setup Utility Security Power Boot Exit Item Specific Help 1. [Removable Devices] 2. [Hard Drive] 3. [ATAPI CD-ROM Drive] IV.
Exit Menu Once you have made all of your selections from the various menus in the Setup program, you should save your changes and exit Setup. Select Exit from the menu bar to display the following menu: Main Advanced PhoenixBIOS Setup Utility Security Power Boot Exit Item Specific Help Exit Saving Changes Exit Discarding Changes Load Setup Defaults Discard Changes Save Changes Select Item Select Menu Enter Change Values Select Sub-Menu F9 Setup Defaults F10 Save and Exit IV.
Exit Menu (Cont’) Exit Saving Changes Once you are finished making your selections, choose this option from the Exit menu to ensure the values you selected are saved to the CMOS RAM. The CMOS RAM is sustained by an onboard backup battery and stays on even when the Notebook PC is turned off. Once this option is selected, a confirmation is asked. Select Yes to save changes and exit.
SECTION 5 USING THE NOTEBOOK PC Introduction This Section describes the basic features and procedures for using your Notebook PC. Topics covered include the floppy drive, CD-ROM drive, pointing device, and other input and output devices. Storage Device Modules Data storage and retrieval are two of the most fundamental tasks you will perform when working with your computer. The Notebook PC is equipped with a 3.5” floppy drive, a hard disk drive, and a CD-ROM drive.
CD-ROM Drive The Notebook PC comes in two models, a CD-ROM model and a DVD model. The DVD model allows the use of both CD-ROM and DVD discs. CD-ROM disks can store a large variety of information, including audio and video data, as well as text files and programs with a maximum of 650MB.
DVD/MPEG2 Option DVD, short for digital versatile disc or digital videodisc, is a new type of CD-ROM that holds a minimum of 4.7GB, enough for a full-length movie or hours of music. The DVD specification supports discs with capacities from 4.7GB to 17GB and access rates up to 22.16MBps. With these capacities and access rates, DVD discs can provide you with a dramatically-enhanced high-color, full-motion video, better graphics, sharper pictures, and Dolby® Digital Surround for a theater-like experience.
Pointing Device The Notebook PC’s integrated Touchpad pointing device is fully compatible with the two-button PS/2 mouse. The Touchpad is pressure sensitive and contains no moving parts; therefore, mechanical failures are unlikely. A device driver is still required for working with some application software. See the Driver & Utility Guide for information on drivers and utilities for the Touchpad.
Pointing Device (Cont’) Double-clicking/Double-tapping - This is a common skill for launching a program directly from the corresponding icon you select. Move the cursor over the icon you wish to execute, press the left button or tap the pad twice in rapid succession, and the system launches the corresponding program. If the interval between the clicks or taps is too long, the operation will not be executed. You can set the double-click speed using the Windows Control Panel “Mouse.
Display Panel The Notebook PC comes with a 14.1” color Thin-Film-Transistor (TFT) Active Matrix display panel that outputs XGA 1024 x 768 resolution with 262,000 colors (32-bit true color). You can also hook up an external CRT or LCD monitor through the VGA connector or just connect a video device such as a TV set through the Video out connector. Display Panel Care The LCD screen is very delicate and requires careful handling.
PC Cards The Notebook PC has two PC Card sockets designed to interface with two Type I or Type II cards, or stacked to accommodate one Type III card. It allows you to expand and customize your computer to meet a wide range of application needs. The PC Card standard accommodates a number of function, communication or data storage expansion options, such as Memory/Flash Cards, FAX/Modems, Hard Disks, and Networking Adapters. The Notebook PC fully supports PCMCIA 2.1, 32-bit CardBus, and Zoomed Video Port.
PC Cards (Cont’) Inserting and Removing a PC Card Follow these instructions, referring to the illustration to insert a PC Card: 1. Insert the PC Card, with the connector side first and label side up, into the socket until it locks firmly into place. The eject lever protrudes out when the card is correctly inserted. 2. The eject lever can be tucked in by pushing it to the right, preventing breakage or accidental ejection. 3. Carefully connect any cables or adapters needed by the PC card.
Multimedia Sound System The Notebook PC’s built-in audio capabilities allow you to take advantage of a wide range of education and entertainment multimedia software available on today’s growing market. The multimedia sound system features an integrated digital audio controller that produces rich, vibrant sound in high quality 16-bit stereo.
IR Wireless Communication The Notebook PC is equipped with an Infrared (IR) Communication Port located on the rear side. The IR port comes with IrDA Serial Infrared Data Link Version 1.1 compliance, which allows you to perform point-to-point wireless communications. You can use a SIR/FIR-specified application to transmit or receive data files with other systems equipped with an infrared port. The following table briefly describes each of the IR modes available.
AC Power System The Notebook PC power is comprised of two parts, the AC Adapter and the battery power system. The AC Adapter converts AC power from a wall outlet to the DC power required by the Notebook PC. The battery pack consists of a set of Lithium-Ion (Li-Ion) battery cells or Nickel-Metal Hydride (NiMH) housed together. There is one battery pack inserted in the Notebook PC. The AC Adapter’s primary function is to provide power to the Notebook PC which also charges the battery pack.
Battery Power System (Cont’) Inserting the Battery Pack Follow these instructions, referring to the illustration to insert a battery pack: 1. Pull open the battery compartment door and pull out the battery lock. 2. Gently slide the battery pack into the bay with the connector facing in and the cloth tab facing out and downward. 3. Lock the battery pack by pressing the battery lock in, and then close the battery compartment door.
Battery Power System (Cont’) Warm-swapping the Battery Packs The Notebook PC’s battery power system supports “Warm-swapping” of battery packs. “Warm-swapping” works with only the Save-to-Disk suspend mode. (A Save-to-Disk partition is required when using Save-to-Disk). To swap the battery when an AC power adapter is not plugged in, place the Notebook PC in suspend mode, swap the battery within 50 minutes, and then press any key to wake up the system.
Battery Power System (Cont’) Battery Gauge & Charging Status The battery status icon on the system status panel indicates the approximate amount of battery remaining through the bars in the four-level-bar gauge and also indicates when the battery is being charged by a blinking outline. When the lowest bar of the four-level-bar gauge starts to flash and you can hear an audible beep. The signal alerts you that the battery is very low.
Power Management Modes (Cont’) Full Power Mode & Maximum Performance The Notebook PC operates in Full Power mode when the power management function is disabled by configuring the BIOS Setup. When the Notebook PC is operating in Full Power Mode, the Power LED remains ON. If you are conscious of both system performance and power consumption, select “Maximum Performance” instead of disabling all power management features.
Power Management Modes (Cont’) A Customized Power-saving Example The timeout settings for System Standby, Auto Suspend, Hard Disk Off, and Video Off specify the amount of time the system must be inactive before the next power management level is enabled. The example below demonstrates this function. If the Hard Disk Timeout is set to 2 minutes, the Standby Timeout to 8 minutes, and Auto Suspend Timeout to 10 minutes, the following power management events will take place: 1. 2. 3.
APPENDIX Appendix DVD Option The following information pertains to the optional DVD drive module. The following specifications are for general reference only and may change without notice.
APPENDIX Data Transfer Rates Appendix CD: Avg. Sustained: CAV mode (8.6x to 20X) DVD: Normal Speed (1X): Partial CAV mode: 647-1500 blocks/sec 1293-3000 kB/sec (mode1), 1474-3429 kB/sec (mode2) 11.08Mbits/sec 11.08-22.16Mbits/sec Data Burst Rates PIO: mode4 (16.67MB/sec) Multiword DMA: mode2 (16.
