User Manual
Table Of Contents
- Safety information
- Chapter 1: Product Introduction
- Chapter 2: Hardware Setup
- 2.1 Chassis cover
- 2.2 Air ducts
- 2.3 Central Processing Unit (CPU)
- 2.4 System memory
- 2.5 Storage devices
- 2.6 Expansion slots
- 2.6.1 Installing an expansion card to the front PCIe riser card bracket (on select models)
- 2.6.2 Installing an ASUS PIKE II card
- 2.6.3 Installing an HBA/RAID card
- 2.6.4 Installing an expansion card to the rear left PCIe expansion card bracket (on select models)
- 2.6.5 Installing an expansion card to the rear right PCIe expansion card bracket (on select models)
- 2.6.6 Installing an OCP 3.0 card to the rear right OCP 3.0 socket board (on select models)
- 2.6.7 (optional) Installing the PFR module
- 2.7 Cable connections
- 2.8 Removable/optional components
- 2.9 Installing GPU cards
- 2.10 Installing Optional Kits
- Chapter 3: BIOS Setup
- 3.1 Managing and updating your BIOS
- 3.2 BIOS setup program
- 3.3 Main menu
- 3.4 Performance Tuning menu
- 3.5 Advanced menu
- 3.5.1 Trusted Computing
- 3.5.2 PSP Firmware Versions
- 3.5.3 Redfish Host Interface Settings
- 3.5.4 AMD CBS
- 3.5.5 APM Configuration
- 3.5.6 Serial Port Console Redirection
- 3.5.7 CPU Configuration
- 3.5.8 PCI Subsystem Settings
- 3.5.9 USB Configuration
- 3.5.10 Network Stack Configuration
- 3.5.11 CSM Configuration
- 3.5.12 NVMe Configuration
- 3.5.13 SATA Configuration
- 3.5.14 AMD Mem Configuration Status
- 3.5.15 Tls Auth Configuration
- 3.6 Chipset menu
- 3.7 Security menu
- 3.8 Boot menu
- 3.9 Tool menu
- 3.10 Save & Exit menu
- 3.11 Event Logs menu
- 3.12 Server Mgmt menu
- Chapter 4: Driver Installation
- Appendix
3-34
Chapter 3: BIOS Setup
The following item appears only when Fan Table Control is set to [Manual].
Low Temperature [0]
Allows you to set the low temperature in °C.
Medium Temperature [0]
Allows you to set the medium temperature in °C.
High Temperature [0]
Allows you to set the high temperature in °C.
Critical Temperature [0]
Allows you to set the critical temperature in °C.
Low Pwm [0]
Allows you to set the low Pwm from 0-100.
Medium Pwm [0]
Allows you to set the medium Pwm from 0-100.
High Pwm [0]
Allows you to set the high Pwm from 0-100.
Temperature Hysteresis [0]
Allows you to set the temperature hysteresis in °C.
Pwm Frequency [25kHz]
Configuration options: [100Hz] [25kHz]
Fan Polarity [Negative]
Configuration options: [Negative] [Positive]
cTDP Control [Manual]
[Auto] Use the fused TDP.
[Manual] User can set customized TDP.
The following item appears only when cTDP Control is set to [Manual].
cTDP [280]
Allows you to customize cTDP.
EfficiencyModeEn [Auto]
[Auto] Use performance optimized CCLK DPM settings.
[Enabled] Use power efficiency optimized CCLK DPM settings.
Power Package Limit Control [Manual]
[Auto] Use the fused PPT.
[Manual] User can set customized PPT.
The following item appears only when Power Package Limit Control is set to [Manual].
Power Package Limit [280]
Allows you to customize PPT.
xGMI Link Width Control [Auto]
[Auto] Use default xGMI link width controller settings.
[Manual] User can set custom xGMI link width controller settings.