User Manual
Table Of Contents
- Safety information
- Chapter 1: Product Introduction
- Chapter 2: Hardware Setup
- 2.1 Chassis cover
- 2.2 Air ducts
- 2.3 Central Processing Unit (CPU)
- 2.4 System memory
- 2.5 Storage devices
- 2.6 Expansion slots
- 2.6.1 Installing an expansion card to the front PCIe riser card bracket (on select models)
- 2.6.2 Installing an ASUS PIKE II card
- 2.6.3 Installing an HBA/RAID card
- 2.6.4 Installing an expansion card to the rear left PCIe expansion card bracket (on select models)
- 2.6.5 Installing an expansion card to the rear right PCIe expansion card bracket (on select models)
- 2.6.6 Installing an OCP 3.0 card to the rear right OCP 3.0 socket board (on select models)
- 2.6.7 (optional) Installing the PFR module
- 2.7 Cable connections
- 2.8 Removable/optional components
- 2.9 Installing GPU cards
- 2.10 Installing Optional Kits
- Chapter 3: BIOS Setup
- 3.1 Managing and updating your BIOS
- 3.2 BIOS setup program
- 3.3 Main menu
- 3.4 Performance Tuning menu
- 3.5 Advanced menu
- 3.5.1 Trusted Computing
- 3.5.2 PSP Firmware Versions
- 3.5.3 Redfish Host Interface Settings
- 3.5.4 AMD CBS
- 3.5.5 APM Configuration
- 3.5.6 Serial Port Console Redirection
- 3.5.7 CPU Configuration
- 3.5.8 PCI Subsystem Settings
- 3.5.9 USB Configuration
- 3.5.10 Network Stack Configuration
- 3.5.11 CSM Configuration
- 3.5.12 NVMe Configuration
- 3.5.13 SATA Configuration
- 3.5.14 AMD Mem Configuration Status
- 3.5.15 Tls Auth Configuration
- 3.6 Chipset menu
- 3.7 Security menu
- 3.8 Boot menu
- 3.9 Tool menu
- 3.10 Save & Exit menu
- 3.11 Event Logs menu
- 3.12 Server Mgmt menu
- Chapter 4: Driver Installation
- Appendix
3-30
Chapter 3: BIOS Setup
The following item appears only when you set PMU Pattern Bits Control to [Manual].
PMU Pattern Bits [0]
Configuration options: [0] - [9]
DRAM Memory Mapping
Chipselect Interleaving [Auto]
Allows you to set interleave memory blocks across the DRAM chip selects for
node 0.
Configuration options: [Disabled] [Auto]
BankGroupSwap [Auto]
Configuration options: [Enabled] [Disabled] [Auto]
BankGroupSwapAlt [Auto]
Configuration options: [Enabled] [Disabled] [Auto]
Address Hash Bank [Auto]
Allows you to enable or disable bank address hashing.
Configuration options: [Enabled] [Disabled] [Auto]
Address Hash CS [Auto]
Allows you to enable or disable CS address hashing.
Configuration options: [Enabled] [Disabled] [Auto]
Address Hash Rm [Auto]
Allows you to enable or disable RM address hashing.
Configuration options: [Enabled] [Disabled] [Auto]
SPD Read Optimization [Auto]
Allows you to enable or disable SPD Read Optimization, if set to [Enabled],
SPD reads are skipped for Reserved fields and most of upper 256 Bytes. If set
to [Disabled], read all 512 SPD Bytes.
Configuration options: [Enabled] [Disabled] [Auto]
NVDIMM
Disable NVDIMM-N Feature [No]
Allows you to disable NVDIMM-N feature for memroy margin tool.
Configuration options: [No] [Yes]
Memory MBIST
MBIST Enable [Disabled]
Allows you to enable or disable Memory MBIST.
Configuration options: [Enabled] [Disabled]
The following items are available only when MBIST Enable is set to [Enabled].
MBIST Test Mode [Auto]
Allows you to select the MBIST Test Mode - Interface Mode (Tests Single and
Multiple CS transactions and Basic Connectivity) or Data Eye Mode (Measures
Voltage vs. Timing).
Configuration options: [Interface Mode] [Data Eye Mode] [Both] [Auto]
MBIST Aggressors [Auto]
Allows you to enable or disable Memory Aggressor test.
Configuration options: [Enabled] [Disabled] [Auto]