User Manual
Table Of Contents
- Safety information
- Chapter 1: Product Introduction
- Chapter 2: Hardware Setup
- 2.1 Chassis cover
- 2.2 Air ducts
- 2.3 Central Processing Unit (CPU)
- 2.4 System memory
- 2.5 Storage devices
- 2.6 Expansion slots
- 2.6.1 Installing an expansion card to the front PCIe riser card bracket (on select models)
- 2.6.2 Installing an ASUS PIKE II card
- 2.6.3 Installing an HBA/RAID card
- 2.6.4 Installing an expansion card to the rear left PCIe expansion card bracket (on select models)
- 2.6.5 Installing an expansion card to the rear right PCIe expansion card bracket (on select models)
- 2.6.6 Installing an OCP 3.0 card to the rear right OCP 3.0 socket board (on select models)
- 2.6.7 (optional) Installing the PFR module
- 2.7 Cable connections
- 2.8 Removable/optional components
- 2.9 Installing GPU cards
- 2.10 Installing Optional Kits
- Chapter 3: BIOS Setup
- 3.1 Managing and updating your BIOS
- 3.2 BIOS setup program
- 3.3 Main menu
- 3.4 Performance Tuning menu
- 3.5 Advanced menu
- 3.5.1 Trusted Computing
- 3.5.2 PSP Firmware Versions
- 3.5.3 Redfish Host Interface Settings
- 3.5.4 AMD CBS
- 3.5.5 APM Configuration
- 3.5.6 Serial Port Console Redirection
- 3.5.7 CPU Configuration
- 3.5.8 PCI Subsystem Settings
- 3.5.9 USB Configuration
- 3.5.10 Network Stack Configuration
- 3.5.11 CSM Configuration
- 3.5.12 NVMe Configuration
- 3.5.13 SATA Configuration
- 3.5.14 AMD Mem Configuration Status
- 3.5.15 Tls Auth Configuration
- 3.6 Chipset menu
- 3.7 Security menu
- 3.8 Boot menu
- 3.9 Tool menu
- 3.10 Save & Exit menu
- 3.11 Event Logs menu
- 3.12 Server Mgmt menu
- Chapter 4: Driver Installation
- Appendix
3-29
ASUS ESC8000A-E11
Common RAS
Data Poisoning [Auto]
Configuration options: [Enabled] [Disabled] [Auto]
DRAM Post Package Repair [Disable]
Allows you to enable or disable DRAM POST Package Repair.
Configuration options: [Enable] [Disable]
RCD Parity [Auto]
Configuration options: [Enabled] [Disabled] [Auto]
DRAM Address Command Parity Retry [Auto]
Configuration options: [Enabled] [Disabled] [Auto]
Max Parity Error Replay [8]
The values in hex, 1, 2, or 3 is invalid.
Configuration options: [0] – [39]
Write CRC Enable [Auto]
Configuration options: [Enabled] [Disabled] [Auto]
DRAM Write CRC Enable and Retry Limit [Auto]
Configuration options: [Enabled] [Disabled] [Auto]
Max Write CRC Error Replay [8]
The values in hex, 1, 2, or 3 is invalid.
Configuration options: [0] – [39]
Disable Memory Error Injection [True]
Configuration options: [False] [True]
ECC Configuration
DRAM ECC Symbol Size [Auto]
Configuration options: [x4] [x8] [x16] [Auto]
DRAM ECC Enable [Auto]
This option allows you to enable or disable DRAM ECC. Auto will set
ECC to enable.
Configuration options: [Disabled] [Enabled] [Auto]
DRAM UECC Retry [Auto]
This option allows you to enable or disable DRAM UECC Retry.
Configuration options: [Disabled] [Enabled] [Auto]
Security
TSME [Auto]
Configuration options: [Disabled] [Enabled] [Auto]
Data Scramble [Auto]
Configuration options: [Disabled] [Enabled] [Auto]
Phy Configuration
PMU Training
DFE Read Training [Auto]
Perform 2D Read Training with DFE on.
Configuration options: [Disabled] [Enabled] [Auto]
FFE Write Training [Auto]
Perform 2D Read WriteTraining with FFE on.
Configuration options: [Disabled] [Enabled] [Auto]
PMU Pattern Bits Control [Auto]
Configuration options: [Auto] [Manual]