User Manual
Table Of Contents
- Safety information
- Chapter 1: Product Introduction
- Chapter 2: Hardware Setup
- 2.1 Chassis cover
- 2.2 Air ducts
- 2.3 Central Processing Unit (CPU)
- 2.4 System memory
- 2.5 Storage devices
- 2.6 Expansion slots
- 2.6.1 Installing an expansion card to the front PCIe riser card bracket (on select models)
- 2.6.2 Installing an ASUS PIKE II card
- 2.6.3 Installing an HBA/RAID card
- 2.6.4 Installing an expansion card to the rear left PCIe expansion card bracket (on select models)
- 2.6.5 Installing an expansion card to the rear right PCIe expansion card bracket (on select models)
- 2.6.6 Installing an OCP 3.0 card to the rear right OCP 3.0 socket board (on select models)
- 2.6.7 (optional) Installing the PFR module
- 2.7 Cable connections
- 2.8 Removable/optional components
- 2.9 Installing GPU cards
- 2.10 Installing Optional Kits
- Chapter 3: BIOS Setup
- 3.1 Managing and updating your BIOS
- 3.2 BIOS setup program
- 3.3 Main menu
- 3.4 Performance Tuning menu
- 3.5 Advanced menu
- 3.5.1 Trusted Computing
- 3.5.2 PSP Firmware Versions
- 3.5.3 Redfish Host Interface Settings
- 3.5.4 AMD CBS
- 3.5.5 APM Configuration
- 3.5.6 Serial Port Console Redirection
- 3.5.7 CPU Configuration
- 3.5.8 PCI Subsystem Settings
- 3.5.9 USB Configuration
- 3.5.10 Network Stack Configuration
- 3.5.11 CSM Configuration
- 3.5.12 NVMe Configuration
- 3.5.13 SATA Configuration
- 3.5.14 AMD Mem Configuration Status
- 3.5.15 Tls Auth Configuration
- 3.6 Chipset menu
- 3.7 Security menu
- 3.8 Boot menu
- 3.9 Tool menu
- 3.10 Save & Exit menu
- 3.11 Event Logs menu
- 3.12 Server Mgmt menu
- Chapter 4: Driver Installation
- Appendix
2-11
ASUS ESC8000A-E11
2.4.2 Memory Configurations
You may install 16GB, 32GB, 64GB, and 128GB RDIMMs into the DIMM sockets. If you
are not sure on which slots to install the DIMMs, you can use the recommended memory
configuration in this section for reference.
• Refer to ASUS Server AVL for the updated list of compatible DIMMs.
• Always install DIMMs with the same CAS latency. For optimum compatibility, it is
recommended that you obtain memory modules from the same vendor.
• All memory modules for 2DPC should be the same.
Recommended dual CPU configuration
DIMMs
2 4 8 16 32
DIMM_H2 • • •
DIMM_H1 •
DIMM_G2 • • •
DIMM_G1 •
DIMM_F2 • •
DIMM_F1 •
DIMM_E2 • •
DIMM_E1 •
DIMM_A1 •
DIMM_A2 • •
DIMM_B1 •
DIMM_B2 • •
DIMM_C1 •
DIMM_C2 • • • • •
DIMM_D1 •
DIMM_D2 • • • •
DIMM_P2 • • •
DIMM_P1 •
DIMM_O2 • • •
DIMM_O1 •
DIMM_N2 • •
DIMM_N1 •
DIMM_M2 • •
DIMM_M1 •
DIMM_I1 •
DIMM_I2 • •
DIMM_J1 •
DIMM_J2 • •
DIMM_K1 •
DIMM_K2 • • • • •
DIMM_L1 •
DIMM_L2 • • • •