User Manual
Table Of Contents
- Safety information
- Chapter 1: Product Introduction
- Chapter 2: Hardware Setup
- 2.1 Chassis cover
- 2.2 Air ducts
- 2.3 Central Processing Unit (CPU)
- 2.4 System memory
- 2.5 Storage devices
- 2.6 Expansion slots
- 2.6.1 Installing an expansion card to the front PCIe riser card bracket (on select models)
- 2.6.2 Installing an ASUS PIKE II card
- 2.6.3 Installing an HBA/RAID card
- 2.6.4 Installing an expansion card to the rear left PCIe expansion card bracket (on select models)
- 2.6.5 Installing an expansion card to the rear right PCIe expansion card bracket (on select models)
- 2.6.6 Installing an OCP 3.0 card to the rear right OCP 3.0 socket board (on select models)
- 2.6.7 (optional) Installing the PFR module
- 2.7 Cable connections
- 2.8 Removable/optional components
- 2.9 Installing GPU cards
- 2.10 Installing Optional Kits
- Chapter 3: BIOS Setup
- 3.1 Managing and updating your BIOS
- 3.2 BIOS setup program
- 3.3 Main menu
- 3.4 Performance Tuning menu
- 3.5 Advanced menu
- 3.5.1 Trusted Computing
- 3.5.2 PSP Firmware Versions
- 3.5.3 Redfish Host Interface Settings
- 3.5.4 AMD CBS
- 3.5.5 APM Configuration
- 3.5.6 Serial Port Console Redirection
- 3.5.7 CPU Configuration
- 3.5.8 PCI Subsystem Settings
- 3.5.9 USB Configuration
- 3.5.10 Network Stack Configuration
- 3.5.11 CSM Configuration
- 3.5.12 NVMe Configuration
- 3.5.13 SATA Configuration
- 3.5.14 AMD Mem Configuration Status
- 3.5.15 Tls Auth Configuration
- 3.6 Chipset menu
- 3.7 Security menu
- 3.8 Boot menu
- 3.9 Tool menu
- 3.10 Save & Exit menu
- 3.11 Event Logs menu
- 3.12 Server Mgmt menu
- Chapter 4: Driver Installation
- Appendix
3-43
ASUS ESC8000A-E11
Soc Miscellaneous Control
ABL Console Out Control [Auto]
[Disable] Disable ConsoleOut Function for ABL.
[Enable] Enable ConsoleOut Function for ABL.
[Auto] Keep default behavior.
The following items are available only when ABL Console Out Control is set to [Enable].
ABL Console Out Serial Port [Auto]
[LPC UART] Enable serial port through LPC UART.
[SOC UART0] Enable serial port through SOC UART0.
[SOC UART1] Enable serial port through SOC UART1.
[Auto] Keep default behavior.
ABL Basic Console Out Control [Enable]
[Enable] Enable Basic ConsoleOut Function for ABL.
[Disable] Disable Basic ConsoleOut Function for ABL.
[Auto] Keep default behavior.
ABL PMU message Control [Auto]
Allows you to control the total number of PMU debug messages. Several major
controls are listed below:
1. Detailed debug messages (e.g., Eye delays)
2. Coarse debug messages (e.g., rank information)
3. Stage completion
4. Firmware completion message only
Configuration options: [Detailed debug message] [Coarse debug messages] [Stage
completion] [Firmware completion message only] [Auto]
Workload Tuning
Workload Profile [Auto]
Allows you to select the profile for different workloads.
[Disabled] Don’t use any workload profile.
[CPU Intensive] Tuned for CPU intensive workloads, providing optimal
integer and floating point performance.
[Java Throughput] Tuned for the highest level of throughput with java
workloads.
[Java Latency] Tuned for the latency sensitive java workloads, to meet
critical SLA’s.
[Power Efficiency] Tuned for optimal power efficiency.
[Memory Throughput Intensive] Tuned for the highest memory throughput available.
[Storage IO Intensive] Tuned for the highest storage IO bandwidth.
[NIC Throughput Intensive] Tuned for maximum TCP/IP and RDMA network
throughput.