User Manual
Table Of Contents
- Safety information
- Chapter 1: Product Introduction
- Chapter 2: Hardware Setup
- 2.1 Chassis cover
- 2.2 Air ducts
- 2.3 Central Processing Unit (CPU)
- 2.4 System memory
- 2.5 Storage devices
- 2.6 Expansion slots
- 2.6.1 Installing an expansion card to the front PCIe riser card bracket (on select models)
- 2.6.2 Installing an ASUS PIKE II card
- 2.6.3 Installing an HBA/RAID card
- 2.6.4 Installing an expansion card to the rear left PCIe expansion card bracket (on select models)
- 2.6.5 Installing an expansion card to the rear right PCIe expansion card bracket (on select models)
- 2.6.6 Installing an OCP 3.0 card to the rear right OCP 3.0 socket board (on select models)
- 2.6.7 (optional) Installing the PFR module
- 2.7 Cable connections
- 2.8 Removable/optional components
- 2.9 Installing GPU cards
- 2.10 Installing Optional Kits
- Chapter 3: BIOS Setup
- 3.1 Managing and updating your BIOS
- 3.2 BIOS setup program
- 3.3 Main menu
- 3.4 Performance Tuning menu
- 3.5 Advanced menu
- 3.5.1 Trusted Computing
- 3.5.2 PSP Firmware Versions
- 3.5.3 Redfish Host Interface Settings
- 3.5.4 AMD CBS
- 3.5.5 APM Configuration
- 3.5.6 Serial Port Console Redirection
- 3.5.7 CPU Configuration
- 3.5.8 PCI Subsystem Settings
- 3.5.9 USB Configuration
- 3.5.10 Network Stack Configuration
- 3.5.11 CSM Configuration
- 3.5.12 NVMe Configuration
- 3.5.13 SATA Configuration
- 3.5.14 AMD Mem Configuration Status
- 3.5.15 Tls Auth Configuration
- 3.6 Chipset menu
- 3.7 Security menu
- 3.8 Boot menu
- 3.9 Tool menu
- 3.10 Save & Exit menu
- 3.11 Event Logs menu
- 3.12 Server Mgmt menu
- Chapter 4: Driver Installation
- Appendix
3-38
Chapter 3: BIOS Setup
Enable AER Cap [Auto]
Allows you to enable or disable Advanced Error Reporting Capability.
Configuration options: [Enable] [Disabled] [Auto]
Early Link Speed [Auto]
Allows you to set Early Link Speed.
Configuration options: [Auto] [Gen1] [Gen2]
Hot Plug Handling mode [Auto]
Allows you to control the Hot Plug Handling mode.
Configuration options: [OS First] [Firmware First] [Auto]
Presence Detect Select mode [Auto]
Allows you to control the Presence Detect Select mode.
Configuration options: [OR] [AND] [Auto]
Preferred IO [Auto]
Allows you to select the preferred IO select type.
Configuration options: [Bus] [Auto]
Data Link Feature Cap [Auto]
Allows you to set Data Link Feature Capability.
Configuration options: [Enabled] [Disabled] [Auto]]
CV test [Auto]
Set this to [Enabled] to support running PCIECV tool. Selecting [Auto] will preserve h/w
defaults.
Configuration options: [Auto] [Disabled] [Enabled]
SEV-SNP Support [Disable]
Configuration options: [Disabled] [Enabled]
SRIS [Auto]
Configuration options: [Auto] [Disable] [Enable]
Compliance Loopback [Auto]
Configuration options: [Auto] [Disable] [Enable]
FCH Common Options
SATA Configuration Options
SATA Enable [Auto]
Allows you to enable or disable OnChip SATA controller.
Configuration options: [Disabled] [Enabled] [Auto]
The following item appears only when SATA Enable is set to [Enabled].
SATA Mode [AHCI]
Allows you to select the OnChip SATA Type.
Configuration options: [AHCI] [AHCI as ID 0x7904] [Auto]