User Manual
Table Of Contents
- Safety information
- Chapter 1: Product Introduction
- Chapter 2: Hardware Setup
- 2.1 Chassis cover
- 2.2 Air ducts
- 2.3 Central Processing Unit (CPU)
- 2.4 System memory
- 2.5 Storage devices
- 2.6 Expansion slots
- 2.6.1 Installing an expansion card to the front PCIe riser card bracket (on select models)
- 2.6.2 Installing an ASUS PIKE II card
- 2.6.3 Installing an HBA/RAID card
- 2.6.4 Installing an expansion card to the rear left PCIe expansion card bracket (on select models)
- 2.6.5 Installing an expansion card to the rear right PCIe expansion card bracket (on select models)
- 2.6.6 Installing an OCP 3.0 card to the rear right OCP 3.0 socket board (on select models)
- 2.6.7 (optional) Installing the PFR module
- 2.7 Cable connections
- 2.8 Removable/optional components
- 2.9 Installing GPU cards
- 2.10 Installing Optional Kits
- Chapter 3: BIOS Setup
- 3.1 Managing and updating your BIOS
- 3.2 BIOS setup program
- 3.3 Main menu
- 3.4 Performance Tuning menu
- 3.5 Advanced menu
- 3.5.1 Trusted Computing
- 3.5.2 PSP Firmware Versions
- 3.5.3 Redfish Host Interface Settings
- 3.5.4 AMD CBS
- 3.5.5 APM Configuration
- 3.5.6 Serial Port Console Redirection
- 3.5.7 CPU Configuration
- 3.5.8 PCI Subsystem Settings
- 3.5.9 USB Configuration
- 3.5.10 Network Stack Configuration
- 3.5.11 CSM Configuration
- 3.5.12 NVMe Configuration
- 3.5.13 SATA Configuration
- 3.5.14 AMD Mem Configuration Status
- 3.5.15 Tls Auth Configuration
- 3.6 Chipset menu
- 3.7 Security menu
- 3.8 Boot menu
- 3.9 Tool menu
- 3.10 Save & Exit menu
- 3.11 Event Logs menu
- 3.12 Server Mgmt menu
- Chapter 4: Driver Installation
- Appendix
3-35
ASUS ESC8000A-E11
The following items appears only when EDC Current Tracking is set to [Enable].
EDC Tracking Current Threshold [0]
The current threshold in AMPs for EDC Current Tracking feature.
EDC Tracking Report Interval [1]
Reporting interval. Every nth observed excursion results in SMU logging a
correctable MCE.
LCLK Frequency Control
Root Complex 0x00 LCLK Frequency [Auto]
Set Root Complex LCLK Frequency (Bus range 0x00-0x1F).
[Auto] Dynamic Frequency Control (Enhanced PIO setting will be
in effect).
[593MHz] Set LCLK Frequency at 593MHz (Overrides Enhanced PIO
setting).
Root Complex 0x20 LCLK Frequency [Auto]
Set Root Complex LCLK Frequency (Bus range 0x20-0x3F).
[Auto] Dynamic Frequency Control (Enhanced PIO setting will be
in effect).
[593MHz] Set LCLK Frequency at 593MHz (Overrides Enhanced PIO
setting).
Root Complex 0x40 LCLK Frequency [Auto]
Set Root Complex LCLK Frequency (Bus range 0x40-0x5F).
[Auto] Dynamic Frequency Control (Enhanced PIO setting will be
in effect).
[593MHz] Set LCLK Frequency at 593MHz (Overrides Enhanced PIO
setting).
Root Complex 0x60 LCLK Frequency [Auto]
Set Root Complex LCLK Frequency (Bus range 0x60-0x7F).
[Auto] Dynamic Frequency Control (Enhanced PIO setting will be
in effect).
[593MHz] Set LCLK Frequency at 593MHz (Overrides Enhanced PIO
setting).
Root Complex 0x80 LCLK Frequency [Auto]
Set Root Complex LCLK Frequency (Bus range 0x80-0x9F).
[Auto] Dynamic Frequency Control (Enhanced PIO setting will be
in effect).
[593MHz] Set LCLK Frequency at 593MHz (Overrides Enhanced PIO
setting).
Root Complex 0xA0 LCLK Frequency [Auto]
Set Root Complex LCLK Frequency (Bus range 0xA0-0xBF).
[Auto] Dynamic Frequency Control (Enhanced PIO setting will be
in effect).
[593MHz] Set LCLK Frequency at 593MHz (Overrides Enhanced PIO
setting).