User Manual
Table Of Contents
- Safety information
- Chapter 1: Product Introduction
- Chapter 2: Hardware Setup
- 2.1 Chassis cover
- 2.2 Air ducts
- 2.3 Central Processing Unit (CPU)
- 2.4 System memory
- 2.5 Storage devices
- 2.6 Expansion slots
- 2.6.1 Installing an expansion card to the front PCIe riser card bracket (on select models)
- 2.6.2 Installing an ASUS PIKE II card
- 2.6.3 Installing an HBA/RAID card
- 2.6.4 Installing an expansion card to the rear left PCIe expansion card bracket (on select models)
- 2.6.5 Installing an expansion card to the rear right PCIe expansion card bracket (on select models)
- 2.6.6 Installing an OCP 3.0 card to the rear right OCP 3.0 socket board (on select models)
- 2.6.7 (optional) Installing the PFR module
- 2.7 Cable connections
- 2.8 Removable/optional components
- 2.9 Installing GPU cards
- 2.10 Installing Optional Kits
- Chapter 3: BIOS Setup
- 3.1 Managing and updating your BIOS
- 3.2 BIOS setup program
- 3.3 Main menu
- 3.4 Performance Tuning menu
- 3.5 Advanced menu
- 3.5.1 Trusted Computing
- 3.5.2 PSP Firmware Versions
- 3.5.3 Redfish Host Interface Settings
- 3.5.4 AMD CBS
- 3.5.5 APM Configuration
- 3.5.6 Serial Port Console Redirection
- 3.5.7 CPU Configuration
- 3.5.8 PCI Subsystem Settings
- 3.5.9 USB Configuration
- 3.5.10 Network Stack Configuration
- 3.5.11 CSM Configuration
- 3.5.12 NVMe Configuration
- 3.5.13 SATA Configuration
- 3.5.14 AMD Mem Configuration Status
- 3.5.15 Tls Auth Configuration
- 3.6 Chipset menu
- 3.7 Security menu
- 3.8 Boot menu
- 3.9 Tool menu
- 3.10 Save & Exit menu
- 3.11 Event Logs menu
- 3.12 Server Mgmt menu
- Chapter 4: Driver Installation
- Appendix
3-34
Chapter 3: BIOS Setup
The following items appear only when xGMI Link Width Control is set to [Manual].
xGMI Force Link Width Control [Unforce]
[Unforce] Do not force the xGMI to a fixed width.
[Force] Force the xGMI to the user specified width.
The following item appears only when xGMI Force Link Width Control is set to [Force].
xGMI Force Link Width [2]
[0] Force xGMI link width to x2.
[1] Force xGMI link width to x8.
[2] Force xGMI link width to x16.
xGMI Max Link Width Control [Auto]
[Auto] Use default xGMI max supported link width.
[Manual] User can set custom xGMI max link width.
The following item appears only when xGMI Max Link Width Control is set to [Manual].
APBDIS [Auto]
[0] Not APBDIS (mission mode)
[1] APBDIS
[Auto] Auto
DF Cstates [Auto]
Allows you to enable or disable DF C-states.
Configuration options: [Disabled] [Enabled] [Auto]
CPPC [Auto]
Configuration options: [Disabled] [Enabled] [Auto]
HSMP Support [Auto]
This option allows you to enable or disable HSMP support.
Configuration options: [Disabled] [Enabled] [Auto]
DLWM Support [Auto]
This option allows you to enable or disable DLWM support.
Configuration options: [Disabled] [Enabled] [Auto]
BoostFmaxEn [Auto]
[Auto] Use the default Fmax.
[Manual] User can set the boost Fmax.
The following item appears only when Boost FmaxEn is set to [Manual].
BoostFmax [0]
Allows you to specify the boost Fmax frequency limit to apply to all cores
(MHz).
EDC Current Tracking [Disable]
The generation of a correctable MCE when the telemetry current value is over
the set threshold defined by EDC Current Tracking Current Threshold.
Configuration options: [Disable] [Enable]