User Manual
Table Of Contents
- Safety information
- Chapter 1: Product Introduction
- Chapter 2: Hardware Setup
- 2.1 Chassis cover
- 2.2 Air ducts
- 2.3 Central Processing Unit (CPU)
- 2.4 System memory
- 2.5 Storage devices
- 2.6 Expansion slots
- 2.6.1 Installing an expansion card to the front PCIe riser card bracket (on select models)
- 2.6.2 Installing an ASUS PIKE II card
- 2.6.3 Installing an HBA/RAID card
- 2.6.4 Installing an expansion card to the rear left PCIe expansion card bracket (on select models)
- 2.6.5 Installing an expansion card to the rear right PCIe expansion card bracket (on select models)
- 2.6.6 Installing an OCP 3.0 card to the rear right OCP 3.0 socket board (on select models)
- 2.6.7 (optional) Installing the PFR module
- 2.7 Cable connections
- 2.8 Removable/optional components
- 2.9 Installing GPU cards
- 2.10 Installing Optional Kits
- Chapter 3: BIOS Setup
- 3.1 Managing and updating your BIOS
- 3.2 BIOS setup program
- 3.3 Main menu
- 3.4 Performance Tuning menu
- 3.5 Advanced menu
- 3.5.1 Trusted Computing
- 3.5.2 PSP Firmware Versions
- 3.5.3 Redfish Host Interface Settings
- 3.5.4 AMD CBS
- 3.5.5 APM Configuration
- 3.5.6 Serial Port Console Redirection
- 3.5.7 CPU Configuration
- 3.5.8 PCI Subsystem Settings
- 3.5.9 USB Configuration
- 3.5.10 Network Stack Configuration
- 3.5.11 CSM Configuration
- 3.5.12 NVMe Configuration
- 3.5.13 SATA Configuration
- 3.5.14 AMD Mem Configuration Status
- 3.5.15 Tls Auth Configuration
- 3.6 Chipset menu
- 3.7 Security menu
- 3.8 Boot menu
- 3.9 Tool menu
- 3.10 Save & Exit menu
- 3.11 Event Logs menu
- 3.12 Server Mgmt menu
- Chapter 4: Driver Installation
- Appendix
3-32
Chapter 3: BIOS Setup
PMU Mem BIST Test Select [Algorithm #1, #2, #3]
Allows you to select the algorithms to use with PMU Mem BIST.
Algorithm #1: Simple Write-Read Static Refresh test; Algorithm #2: Write/Read/
Write data test; Algorithm #3: Agressor Row stress test
Configuration options: [Algorithm #1] [Algorithm #2] [Algorithm #1, #2]
[Algorithm #1, #3] [Algorithm #2, #3] [Algorithm #1, #2, #3]
NBIO Common Options
IOMMU [Auto]
Allows you to enable or disable IOMMU.
Configuration options: [Disabled] [Enabled] [Auto]
DMAr Support [Auto]
Allows you to enable DMAr system protection during POST.
Configuration options: [Disable] [Enable] [Auto]
DRTM Virtual Device Support [Auto]
Allows you to enable DRTM ACPI virtual device.
Configuration options: [Disable] [Enable] [Auto]
ACS Enable [Auto]
AER must be enabled for ACS enable to work.
Configuration options: [Disable] [Enable] [Auto]
PCIe ARI Support [Auto]
This item enables Alternative Routing-ID Interpretation.
Configuration options: [Disable] [Enable] [Auto]
PCIe ARI Enumeration [Auto]
Allows ARI Forwarding for each downstream port.
Configuration options: [Disable] [Enable] [Auto]
PCIe Ten Bit Tag Support [Auto]
This item enables PCIe ten bit tags for supported devices. [Auto] = [Disabled].
Configuration options: [Disable] [Enable] [Auto]
HD Audio Enable [Auto]
Configuration options: [Disabled] [Enable] [Auto]
SMU Common Options
Determinism Control [Manual]
[Auto] Use the fused Determinism.
[Manual] User can set customized Determinism.
The following item appears only when Determinism Control is set to [Manual].
Determinism Slider [Power]
Configuration options: [Auto] [Power] [Performance]
Fan Control
Fan Table Control [Auto]
[Auto] Use the default fan table.
[Manual] User can set customized fan table.
Determinism Slider [Power]
Configuration options: [Auto] [Power] [ Performance]